• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.35 no.7
• /
• pp.709-715
• /
• 2011

Harmonic drives have been widely used in combination with joint torque sensors in order to facilitate accurate manipulator control. A harmonic drive causes a torque ripple because of its structural characteristics, and this torque ripple tends to deteriorate the performance of a controller or observer that uses torque sensors. This paper proposes a switching notch filter for reducing the torque ripple caused by a harmonic drive in a joint torque sensor; the functioning of this filter is based on the relationship between the frequency components of the torque ripple and the rotational velocity of the harmonic drive. The proposed switching notch filter is advantageous in that it requires less computational load and does not necessitate additional circuits or structures. Various experiments demonstrate that the proposed filter has good filtering performance, fast response, and good switching stability.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2010.11a
• /
• pp.233-234
• /
• 2010

• Composites Research
• /
• v.14 no.2
• /
• pp.13-21
• /
• 2001

Substituting composite structures for conventional metallic structures has many advantages because of higher specific stiffness and specific strength of composite materials. In this work, one-piece driveshafts composed of carbon/epoxy and glass/epoxy composites were designed and manufactured for a rear wheel drive automobile satisfying three design specifications, such as static torque transmission capability, torsional buckling and the fundamental natural bending frequency. Single lap adhesive joint was used to join the composite shaft and the aluminum yoke. The torque transmission capability of the adhesively bonded composite shaft was calculated with respect to bonding length and yoke thickness by finite element analysis and compared with the experimental result. Torque transmission capability was based on the Tsai-Wu failure index fur composite shaft and the failure model which incorporated the nonlinear mechanical behavior of aluminum yoke and epoxy adhesive. From the experiments and the finite element analyses, it was found that the static torque transmission capability of the composite driveshaft was highest at the critical yoke thickness, and saturated beyond the critical length. Also, it was found that the one-piece composite driveshaft had 40% weight saving effect compared with a conventional two-piece steel driveshaft.

• Journal of Institute of Control, Robotics and Systems
• /
• v.4 no.1
• /
• pp.10-18
• /
• 1998

불확실한 변수와 비선형성을 가지는 유연조인트 로봇의 견실제어 방안을 제시한다. 그리고 본 시스템에서 불확실구조는 일치성을 유지하지 않는 불일치성 불확실 시스템이다. 제어기는 리아노프의 방안에 근거를 두고있다. 견실제어는 연산토크법을 사용하고 삽입제어기법을 통하여 좌표변환을 통해 구성된다. 제어기 설계과정은 우선 연산토크방법에 의해 시스템 동역학에서 정격부분을 선형으로 2개의 부분시스템으로 구성한다. 이후 좌표변환을 이용하여 각 부분시스템에 제어기를 구축한다. 이 방안을 통하여 관성 행렬이 알려진 값인 경우 이 행렬의 상위한계 조건없이 제어기를 설계할 수 있다. 따라서 임의의 형태의 로봇에도 적용 가능한 제어알고리즘이 된다. 설계된 견실제어는 변환된 시스템이나 원시스템 모두 실용적 안정성을 보장한다. 이 변환은 단지 불확실변수의 최대 한계값의 정보만을 요구한다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.281-282
• /
• 2011

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.2
• /
• pp.515-522
• /
• 1991

Determining the motion using optimal technique about traveling time and trajectory planning has been studied often in recent years, but the study of determining the optimal robot dimensions is rare, the authors attempt to find out the least driving torques and energy as the optimization of link length ratio referred to 2R SCARA and 3R robot manipulators. For the given linear path with triangular velocity profile, the inverse kinematic and dynamic problems are examined in order to lead into solution of problem, which is suggested for optimal design of link lengths. Accordingly, optimal link length ratio is obtained with respect to each case.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.17 no.8
• /
• pp.1980-2000
• /
• 1993

The stresses and torque transmission capabilities of adhesively bonded circular, hexagonal and elliptical lap joints were analyzed by the finite element and compared with the experimental results. The adherends of the joints were composed of carbon fiber/epoxy composite shafts and steel shafts. In calculating the torque transmission capabilities, the linear laminate properties of the composite material and the nonlinear shear properties of the adhesive were used. Using this method, the torque transmission capabilities of adhesively bonded lap joints could be obtained within 10% error compared to the experimental results except some single lap joints. The experiments revealed that the hexagonal joint had the best torque transmission capability from the single lap joints and the double lap joint had better torque transmission than the single lap joint.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.9
• /
• pp.869-876
• /
• 2017

Analysis of actuating forces and joint reaction forces are essential to determine the capacity of actuators, to control the mechanical system and to design its components. This paper presents an algorithm that calculates actuating forces(or torques), depending on the various types of driving constraints, in order to produce a given system motion in the joint coordinate space. The joint coordinates are used as the generalized coordinates of a kinematic system. System equations of motion and constraint acceleration equations are transformed from the Cartesian coordinate space to the joint coordinate space using the velocity transformation method. A numerical example is carried out to verify the algorithm proposed.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.19 no.7
• /
• pp.1651-1656
• /
• 1995

The adhesively bonded tubular single lap joint shows large nonlinear behavior in the loaddisplacement relation, because structural adhesives for the joint are usually rubber toughened, which endows adhesives with nonlinear shear properties. since the majority of load transfer of the adhesively bonded tubular single lap joint is accomplished by the nonlinear behavior of the adhesive, its torque transmission capability should be calculated incorporating nonlinear shear properties. However, both the analytic and numerical analyses become complicated if the nonlinear shear properties of the adhesive are included during the calculation of torque transmission capabilities. In this paper, in order to obtain the torque transmission capabilities easily, an iterative solution which includes the nonlinear shear properties of the adhesive was derived using the analytic solution with the linear shear properties of the adhesive. Since the iterative solution can be obtained very fast due to its simplicity, it has been found that it can be used in the design of the adhesively bonded tubular single lap joint.

• Composites Research
• /
• v.19 no.3
• /
• pp.29-36
• /
• 2006

Since composite materials have anisotropic properties that depend on their stacking angle and sequence, the analysis of joints with isotropic adherends is limited in describing the behavior of the adhesive Joint with composite adherends. In this study, the nonlinear solution for adhesive joints with composite adherends was derived by incorporating the nonlinear behavior of the adhesive into the analysis. The behavior of the laminated composite tube was first analyzed, and the stress distributions of the composite tubular adhesive joint were calculated by including the nonlinear properties of the adhesive. The effect of the stacking sequence of composite adherends and bonding length on torque capacities of joints was examined, and results of the nonlinear analysis were also compared with those of the linear analysis.