• Journal of Aerospace System Engineering
• /
• v.7 no.4
• /
• pp.18-26
• /
• 2013

The technique of sliding mode control has been introduced and designed for jet engine controller. For designing the controller for controlled element, the state space model of the turbojet engine is derived in advance from the perturbation of non-linear engine dynamic equation at operation point. Based upon the jet engine model, the robust sliding mode controller is proposed associated with the optimum sliding mode function. The numerical simulation demonstrates that the designed sliding mode controller proves its effectiveness for the jet engine by showing superior control performances over the conventional PI controller with fast responses and robustness to disturbance.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.5 no.1
• /
• pp.107-115
• /
• 2002

In this paper, spray and combustion characteristics of a liquid-fueled ramjet engine were experimentally investigated. The spray penetrations were measured to clarify the spray characteristics of a liquid jet injected transversely into the subsonic vitiated airstream, which Is maintained a high velocity and temperature. The spray penetrations are increased with decreasing airstream velocity, increasing airstream temperature, and increasing air-fuel momentum ratio. To compensate our results of penetrations, the new experimental equation were modified from Inamura's equation. In the case of insufficient penetration, the combustion phenomenon in ram-combustor were unstable. Therefore, the sufficient penetration must be considered to make a stable flame.

• Journal of ILASS-Korea
• /
• v.24 no.3
• /
• pp.130-136
• /
• 2019

Spray visualization of a vaporizer fuel injection system of a micro turbo jet engine was experimentally studied. The fuel heating by combustion was simulated by the high pressure steam generator and combustor inlet air from the centrifugal compressor was simulated by compressed air stored in the high pressure air tank. Spray visualization was performed with single vaporizer, and then six vaporizers which are same number of micro turbojet engine were used. As a results, the spray characteristics of the vaporizer were understood with pressure difference of the combustor inlet air and the fuel supply pressure. Spray angles with three types of vaporizer configuration were measured. In the results, guide vane configuration has a wider spray angle than the straight tube and smooth curve tube with a swirler, so it is expected that the fuel will be effectively distributed inside the combustor flame tube.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.3 no.2
• /
• pp.18-24
• /
• 1999

Liquid ramjet combustor is closely connected with complex phenomena due to a series of processes such as intake air, spray, mixing, and combustion. The present numerical experiments were peformed to investigate these flow characteristics for two and three dimensional liquid ramjet combustor. Grid system was made with three domains: intake region where air is supplied and fuel is injected, combustor and nozzle region, and exit atmosphere region. The numerical results showed that two and three dimensional flow patterns in recirculation region of combustor were significantly different each other and spray model was necessary to predict correctly the chemical reaction flow characteristics. Numerically examined for two different location of fuel injector, one is located on the bottom position of curved intake and the other is located on the top position. We found that bottom position of fuel injector is better than top position because fuel influx to the recirculation region which is need to sustain chemical reaction is more than the latter.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.39 no.4
• /
• pp.321-331
• /
• 2011

The present work is aimed to analyze the creep characteristics of a turbojet engine turbine blade using the theta projection method. The theta projection method has been widely used due to its advantages and flexibility. For the creep characteristic analysis of the turbine blade, tests are performed considering the operating conditions and the non-linear material properties. Results from the creep test are fitted using the four theta model. The predicted proprieties using the four theta model are compared with the prediction model and creep test results. To obtain an optimum value of the four theta parameters in non-linear square method, a number of computing processes in the non-linear least square method were carried out to obtain full creep curves. Results using the theta model has more than 0.95 value of $R^2$. The results between the experimental values and predicted four theta model has about 90.0% accuracy. The theta projection method can be utilized for a design purpose to predict the creep behavior.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.25 no.2
• /
• pp.42-54
• /
• 2021

The Aft-deck is being applied to the latest unmanned aircraft for the purpose of shielding the gas turbine exhaust plume or spreading jets to increase the mixing rate with the ambient air, thereby reducing the temperature of exhaust gases. In this study, we would like to find out how the performance of the nozzle is affected by the design variables of the Aft-deck. The design variables of aft-deck are selected as length, expansion angle and upper deck shape. The correlation between thrust and plume shielding rate with the length variable is presented. And the correlation between the thrust and the jet diffusion range is presented according to the expansion angle. In addition, the thrust increase effect is confirmed by the removal of the upper deck and the characteristics of transverse velocity vector determined mixing performance with external flow.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.2 no.2
• /
• pp.14-23
• /
• 1998

The present study investigates numerically particle laden flow through compressor cascade. In general, a lot of turbine engines are affected by various particles which are suspending in the atmosphere. Especially in the case of aircraft aviating in volcanic, industrial and desert region including many particles, each components of engine system are damaged severely. That damage modes are erosion of compressor binding and rotor path components, partial or total blockage of cooling passage and engine control system degradation.. Initial damages can not be serious but cumulation of damages influences on safety of aircraft control and economical maintenance cost of engine system can be increased. When dust, materials and volcanic particles in the atmosphere flow in the compressor, it is necessary to predict damaged and deposited region of compressor blades. To the various flow inlet angle, predictions of particles trajectory in compressor cascade by Lagrangian method are presented and impulses by impaction of particles at blade surface are calculated. By the definition of particle deposition efficiency, characteristics of particles impact are considered quantitatively. With these prediction and experimental data, erosion rates are predicted for two materials - ceramic, soft metal - on compressor blade surface. Improvements like coating of blade surface could be found, by above prediction.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1998.04a
• /
• pp.17-24
• /
• 1998

압축기의 종류는 크게 dynamic type과 positive displacement type으로 우선 나눌 수 있다. 전자는 제트엔진에 사용되는 압축기에서 보는 바와 같이 기체의 속도를 변화시켜 동압을 정압으로 바꾸어 압력을 얻는 경우이다. 후자는 기체를 둘러싼 체적을 줄여서 압력을 얻는데 가전제품에 쓰이는 냉각용 압축기의 대부분의 종류가 이에 해당된다. 압축 기체의 종류에 따라 공기 압축기, 가스 압축기, 냉각용 압축기로도 나눌 수 있겠다. 냉각용 압축기는 다시 여러 가지 방법으로 분류할 수 있겠지만, 구동 모타의 용량이나 냉각 용량에 따라, 대형, 소형으로 분류하거나, 압축기를 둘러싼 셀의 구조에 따라 밀폐형과 반 밀폐형으로 나눌 수 있다. 밀폐형은 냉매를 반 영구적으로 보충할 필요가 없도록 용접형 셀을 가진 구조로 압축기를 다시 열어서 보수할 수가 없다. 냉장고나 냉방기 같은 가전 제품에 쓰이는 압축기는 대부분 소형 밀폐형이 되겠다. 산업용의 중,대형 압축기는 보수의 목적으로, 자동차 냉방용 압축기는 동력이 엔진축에서 공급되는 구조 상의 이유로 반 밀폐형이 채택된다. 보수가 사실상 불가능한 밀폐형의 구조 상 소형 냉장용 압축기는 거의 무한 수명을 감안한 설계를 요하게 되고, 이것이 압축기의 보수적인 설계 및 개발 성향에 어느 정도 영향을 주었다고 볼 수 있다. 이런 소형 밀폐형 압축기(positive displacement, fractional horsepower, hermetic compressor)에 관한 연구의 소개가 이 글의 주 관심이 되겠다. 압력을 얻기 위해 체적을 변화시키는 mechanism도 여러 가지가 있는 바, 왕복동식 피스톤(reciprocating piston) 압축기가 가장 오랫동안 사용되어 온 구조이다. 회전식으로 압축을 얻는 방식으로는 로타리 피스톤식, 스크류식, 스크롤식 압축기가 있다. 로타리 피스톤(rotary piston)식 압축기는 약 20여년 전 부터 냉방용 압축기에서부터 널리 쓰이게 되었다. 약 10여년전부터 상용화 된 스크롤(scroll) 형 압축기도 현재 상대적으로 용량이 큰 가정용 냉방기를 중심으로 많이 쓰이고 있다. 스크류형 압축기는 보통 중대형 상업용에 주로 쓰인다.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.19 no.4
• /
• pp.61-68
• /
• 2015

Reactive sprays of two propellant combinations(GOx/kerosene and $GN_2O$/ethanol) were observed and compared with each other as a basic research of visualizing supercritical combustion. A shadowgraph imaging method was used to visualize the reactive sprays, and shadowgraph images were converted to density gradient magnitude images to analyse the structure of reactive sprays. The gas-liquid interface of GOx/kerosene spray showed rougher boundary and steeper density gradient near the injector face than the $N_2O$/ethanol at similar combustion chamber pressure. Spray core length was calculated from averaged density gradient magnitude images and it was revealed that spray core length of GOx/kerosene was shorter than that of $GN_2O$/ethanol, although momentum flux ratio of GOx/kerosene propellant combination was lower.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.253-256
• /
• 2009

In the micro turbojet engine less than 350kw power class, it is not easy to find out the good atomization fuel injector with good spray quality. However conceptually, rotating fuel injection system can give high atomization quality by only the centrifugal force of a high speed rotating shaft of the engine without high-pressure fuel pump. With this motivation, we manufactured very small rotating fuel injector of 40 mm diameter and performed under a variety of injection orifices. We measured droplet size, velocity and spray distribution by the PDPA(Phase Doppler Particle Analyzer) system. Also spray was visualized by using high speed camera. From the test results, we could understand that the length of liquid column from the injection orifice is mainly controlled by the rotational speeds. Furthermore, droplet size(SMD) is decreased with the rotational speeds and is influenced by the diameter of the injection orifice and liquid film thickness.