• Journal of IKEEE
• /
• v.24 no.2
• /
• pp.392-402
• /
• 2020

This paper proposes a solar tracking system without photo-sensors. The system can be classified into four modules: Solar Tracking, MPPT, ESS, and Real-Time Monitoring. Nine solar panels, as a basic unit, are adopted with grid structures of different heights to reduce wind influence and to enable solar tracking without photo-sensors. The low-cost MCU implements MPPT method which generates PWM switching signal for boost converter. The unit of ESS consists of three-series and four-parallel lithium-ion batteries in order to enable monitoring for abnormalities in temperature and electrical characteristics of battery. Four MCUs used in the system consists of two AVR Atmega128, and two Raspberry PI, and they exchanges operation informations. Experimental results of the proposed system show the solar tracking performance, the possibility of on-site and remote monitoring and the convenience of maintenance based on IoT technology.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.39 no.12
• /
• pp.1062-1070
• /
• 2002

In this paper, variable radix-two multibit coding algorithm is presented and applied in the implementation of discrete cosine transform(DCT) and inverse discrete cosine transform(IDCT). Variable radix-two multibit coding means the 2k SD (signed digit) representation of overlapped multibit scanning with variable shift method. SD represented by 2k generates partial products, which can be easily implemented with shifters and adders. This algorithm is most powerful for the hardware implementation of DCT/IDCT with constant coefficient matrix multiplication. This paper introduces the suggested algorithm, it's proof and the implementation of DCT/IDCT The implemented IDCT chip with 8 PEs(Processing Elements) and one transpose memory runs at a tate of 400 Mpixels/sec at 54MHz frequency for high speed parallel signal processing, and it's verified in HDTV and MPEG decoder.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.13 no.3
• /
• pp.11-15
• /
• 1976

한국산 천연수정은 보석장식용으로서는 그 품질이 이미 알려져 있으나 수정진동자로서의 특성에 관해서는 아직 보고된 바가 없다. 본 연구는 특히 경상도일대에서 채굴되고 있는 천연수정을 채집, 선별, 가공하여 그 수정진동자로서의 사용가능성을 실험을 통하여 검토한 것이다. 필자들은 채굴현장 근처에서 채집한 원석을 특별히 고안제작된 검사경을 이용하여 분석선별하였으며 X-ray를 사용하여 AT-cut로 orientation 한후 시판을 절단하였다. 다음 적용하여 전기적, 광학적 쌍수상태를 검토하고 다시 선별하였다 Dimensioning은 5MHz를 목표로 하였는데 연잠제를 사용하여 5MHz의 조도까지 연마하고 전극으로서 표준형의 은막을 부착하여 시판을 완성하였다. 시판을 대한 측정결과는 모든 등가정수가 대표적인 수입수정판의 것과 대등하였으며 특히 Q는 모두 105를 넘었다. 온도특성도 AT-cut의 이론치와 대차가 없었으며 -20℃-+100℃ 범위에서 최대 20PPM 이내의 편차를 보였다. 즉, 한국산 천연수정은 적절히 선별, 가공 한다면 부유한 수정진동자의 원재로서 사용할수 있음이 증명되었다. Samples of domestic natural quartz were collected and screened optically and chemically, and, after weeding out portions unfit for electrical resonator, were cut into AT-cut wafers, which in turn were dimensioned, trimmed and lapped into 5MHz resonator units. The results of measurements obtained from the specimens indicated excellent electrical characteristics of domestic natural quartz with the average Q quotient of 10s or higher. Temperature characteristics also showed typical AT-cut corves with the frequency deviation of 20PPM at maximum throughout the range of -20 to 100℃. The experiment on the initial batch of samples amply indicates the excellent electrical quality of domestic natural quartz as quartz resonator units.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.48 no.7
• /
• pp.76-81
• /
• 2011

A new via cutting structure in 2-layer DRAM package substrate has been fabricated to lower its power distribution network(PDN) impedance. In new structure, part of the via is cut off vertically and its remaining part is designed to connect directly with the bonding pad on the package substrate. These via structure and substrate design not only provide high routing density but also improve the PDN impedance by shortening effectively the path from bonding pad to VSSQ plane. An additional process is not necessary to fabricate the via cutting structure because its structure is completed at the same time during a process of window area formation. Also, burr occurrence is minimized by filling the via-hole inside with a solder resist. 3-dimensional electromagnetic field simulation and S-parameter measurement are carried out in order to validate the effects of via cutting structure and VDDQ/VSSQ placement on the PDN impedance. New DRAM package substrate has a superior PDN impedance with a wide frequency range. This result shows that via cutting structure and power/ground placement are effective in reducing the PDN impedance.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.5
• /
• pp.962-969
• /
• 2006

To address the importance of the process fault detection for productivity, support vector machines (SVMs) is employed to assist the decision to determine process faults in real-time. The reactive ion etching (RIE) tool data acquired from a production line consist of 59 variables, and each of them consists of 10 data points per second. Principal component analysis (PCA) is first performed to accommodate for real-time data processing by reducing the dimensionality or the data. SVMs for eleven steps or etching m are established with data acquired from baseline runs, and they are further verified with the data from controlled (acceptable) and perturbed (unacceptable) runs. Then, each SVM is further utilized for the fault detection purpose utilizing control limits which is well understood in statistical process control chart. Utilizing SVMs, fault detection of reactive ion etching process is demonstrated with zero false alarm rate of the controlled runs on a run to run basis.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.36 no.8
• /
• pp.811-819
• /
• 2012

An air-cooled condenser is a device that is used for converting steam into condensate by using ambient air. The air-cooled condenser is prone to suffer from a serious explosion when the condensate inside the tubes of a heat exchanger is frozen; in particular, tubes can break during winter. This is primarily due to the structural problem of the tube outlet of an existing conventional air-cooled condenser system, which causes the backflow of residual steam and noncondensable gases. To solve the backflow problem in such condensers, such a system was simulated and a new system was designed and evaluated in this study. The experimental results using the simulated condenser showed the occurrence of freezing because of the backflow inside the tube. On the other hand, no backflow and freezing occurred in the advanced new condenser, and efficient heat exchange occurred.

• Archives of design research
• /
• v.14
• /
• pp.283-294
• /
• 1996

This study is one of the many tnals which would prove the need of linguistic approach to the process of making and evaluating design. Also, this study is a suggestion that a concept of metonymy should be applied to the field of desIgn. In ord"r to proceed above thesis, this study, begins with emploY1Og an linguistIc eye isual language, in the fIeld of design. Secondly, the method of exitence and the positive meaning of metonymy wIll be ecplained in the relation to the post-structural and post-modern thinking structure. ThIS IS because through the use of metonymy, people can express theIr concern about particularity and individuality whIch Modernist universality skept over. Finally, this sudy proves the validity of employing the concept of metomyny 10 the field of post-modern design by analizing actual examples.ples.

• Journal of radiological science and technology
• /
• v.39 no.4
• /
• pp.631-636
• /
• 2016

Hitherto, spatial resolution has commonly been evaluated by test patterns or phantoms built on some specific distances (from close to far) between two objects (or double targets). This evaluation method's shortcoming is that resolution is restricted to target distances of phantoms made for test. Therefore, in order to solve the problem, this study proposes and verifies a new method to efficiently test spatial resolution with a single target. For the research I used PSF and JND to propose an idea to measure spatial resolution. After that, I made experiments by commonly used phantoms to verify my new evaluation hypothesis inferred from the above method. To analyse the hypothesis, I used LabVIEW program and got a line pixel from digital image. The result was identical to my spatial-resolution hypothesis inferred from a single target. The findings of the experiment proves only a single target can be enough to relatively evaluate spatial resolution on a digital image. In other words, the limit of the traditional spatial-resolution evaluation method, based on double targets, can be overcome by my new evaluation one using a single target.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.6
• /
• pp.615-620
• /
• 2013

There is considerable interest in developing energy sources capable of larger power densities. In our previous works, we proved that by coupling an exothermic chemical reaction with 1D nanostructures, a self-propagating reactive wave can be driven along its length with a concomitant electrical pulse of high specific power, which we identified as a thermopower wave. Herein, we discuss details about many different aspects of a thermopower wave. Different alignment degree in vertically aligned CNT films is evaluated in the reactive wave speed and correlated with its thermal reaction that affects the change in the magnitude of energy generation. The effects of the temperature-dependent properties of chemical fuels and CNTs are evaluated. Furthermore, we explore the convection and radiation portions in this thermal wave as well as the synchronization between the thermal reaction transfer and the oscillation of the electrical signal.

• Journal of Life Science
• /
• v.9 no.1
• /
• pp.50-57
• /
• 1999

STATs activated by various cytokine and growth factors trigger a quick response in the nucleus and induce changes in gene expression. We have found the sequences homologous to STAT binding site in the 5'-flanking region of the D-raf gene. In this study, we examined role of the STAT binding site in D-raf gene promoter activity in vivo by using transgenic flies. The reporter plasmid pDraf-STATmut-lacZ was constructed by fusing D-raf promoter fragment having the base-substituted STAT binding site with the lacZ gene in a P-element vector. Transgenic flies bearing the Draf-STATmut-lacZ fusion genes were established by P-element mediated transformation. The expression of lacZ in transgenic flies bearing Draf-STATmut-lacZ fusion genes carrying base substitution in STAT site throughout various developmental stages was extensively reduced in comparison with that in transgenic flies bearing wild type Draf-lacZ fusion gene. These results show that the STAT binding site plays an important role in regulation of the D-raf gene.