• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.6 no.4
• /
• pp.86-91
• /
• 2007

The heat generated by the brake system of vehicles results in reduction of friction force on the brake surface and vibration when breaking. These problems play essential part in break's performance. To solve these problems, extensive research has been conducted such as drilling cooling holes on the brake pud, accommodating ventilated holes and etc. In this study, we suggest the compression of brake in circumferential direction in order to improve its cooling performance. And we analyzed comparing temperature distribution which is generated accomplishing heat analysis at each disc.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2004.10a
• /
• pp.445-450
• /
• 2004

Recently, many studies have been performed and good results have been reported in literature on the prediction of the brake disk temperature. However, study on the brake fluid temperature is rarely found despite of its importance. In this study, brake fluid temperature is predicted according to material property of brake piston. For the analysis, a typical disk-pad brake system is modeled including the brake disk, pad, caliper, piston and brake fluid. Vehicle deceleration, weight distribution by deceleration, disc-pad heat division and the cooling of brake components are considered in the analysis of heat transfer. Unsteady-state temperature distribution are analyzed by using the finite element method and numerical results are compared with the vehicle test data

• Proceeding of EDISON Challenge
• /
• 2017.03a
• /
• pp.351-357
• /
• 2017

차량용 브레이크의 성능은 브레이크 디스크 로터의 냉각 성능과 밀접한 관련이 있다. 냉각 성능 향상을 위해 디스크 로터에 구멍을 뚫거나 홈을 깎아내어 열 전달면을 극대화 시키거나 열 전도도가 높은 재료에 대한 연구가 활발하게 진행되고 있다. 본 연구에서는 각각 형상이 다른 디스크 브레이크 시스템의 방열 및 제동 성능, 패드 압력에 대한 응력을 분석하고 온도장 근사 및 열전도 해석 프로그램(Heat_transfer, KAIST, EDISON)과 Elastic-Plastic Analysis SW(CSD_EPLAST, 서울과학기술대학교, EDISON) 및 ABAQUS를 이용해 각각의 냉각 성능 및 응력 분포를 비교 분석한다.

• Proceedings of the KSR Conference
• /
• 2003.10c
• /
• pp.383-388
• /
• 2003

This study investigates the change of the temperature and mechanical properties of the braking disk for the railway vehicle. The average temperature is measured about $100^{\circ}C$ and the maximum temperature is measured over $200^{\circ}C$ by non-contact sensor from Seoul to Chunan. In the $20^{\circ}C-300^{\circ}C$, the $0.2\%$ offset yield strengths of the disk (GC25-30 material) are a little down to the reference value, but the linear relation of tensile test result is not find from the linear change of temperature. However, $J_{IC}$ values have the inverse proportion to the temperature, and the $J_{IC}$ value at $200^{\circ}C$ decrease $30.55\%$ from the $J_{IC}$. value of the room temperature. This result means that the crack length on the braking disk is rapidly increase at $200^{\circ}C$

• Journal of Advanced Marine Engineering and Technology
• /
• v.25 no.4
• /
• pp.809-816
• /
• 2001

This is a fundamental study to improve the performance of the LPG engine. The result were summarized as followed. 1. The measured torque and power on the fuel of LPG were indicated about 8% lower than those on gasoline with the same compression ratio. 2. In the case of LPG, BSFD at compression ratio of 9.7 was about 5% lower than that of 8.3 at 3,000ppm 3. HC and CO concentrations of the LPG were lower about 53%, 35% than those of gasoline

• Journal of Energy Engineering
• /
• v.25 no.2
• /
• pp.21-28
• /
• 2016

This research was conducted for the optimal design of large commercial gas oven system. Equivalent ratio was determined through a numerical analysis and experiments on the combustion condition of the combustor. After reviewing the supply capacity of burner(20,000 kcal) and control method of convection fan, two types of heat exchangers designed. In order to maintain a uniform temperature inside the oven is required convection fan braking system. The center temperature in the oven rises more rapidly when the convectional fan is rotated in the counterclockwise direction than the counter-clockwise direction. And The efficiency of the system by installing a large heat transfer area was higher.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.41 no.1
• /
• pp.21-30
• /
• 2017

The surface temperature of disc brakes varies during braking, which can affect the friction and wear behavior of braking systems. In order to develop an efficient braking system, the friction and wear behaviors of brake materials need to be clearly understood. In this work, the friction and wear behavior of the C/C-SiC-Cu composite and the Al/SiC composite, which are used in disc braking systems, were investigated. Both the surface temperature and contact pressure were studied. A pin-on-reciprocating tribotester was used for this purpose, in order to control temperature and load. Results showed that the friction varied significantly with temperature and sliding distance. It was found that a transfer layer of compacted wear debris formed on the wear track of the two materials. These layers caused the surface roughness of the wear track to increase. The outcome of this work is expected to serve as a basis for the development of braking systems under various operating conditions.

• Journal of the Korean Institute of Gas
• /
• v.13 no.5
• /
• pp.1-6
• /
• 2009

This paper presents the fuel consumption effects of LPG vehicle depending on the atmospheric temperature, LP gas leakage of vaporizer, viscosity of engine oil and engine load conditions. The fuel consumption test results show that when the temperature of engine temperature rises, the fuel consumption efficiency increases in general. The fuel consumption efficiency for an atmosphere temperature of $24.2^{\circ}C$ is 13.6% high compared to that of $1^{\circ}C$. No leak vaporizer on fuel consumption efficiency is 5.3% high compared to that of the LP gas leak vaporizer. The fuel economy of new engine oils is just 1.1% high compared to that of used oils with a LPG vehicle mileage of 9,500km. This is not an influential factor compared with an atmospheric temperature and a LP gas leakage. The more important factors on the fuel consumption efficiency are driving conditions such as a rapid braking, abrupt start and fast acceleration. The test results indicate that the normal start is 32.3% high compared to that of an abrupt start and the fast acceleration is 10.8% high compared with that of an abrupt start. And the fuel consumption efficiency for a rapid braking is 18.3% higher than that of an abrupt start. These indicate that the driving condition is very important to reduce the fuel consumption rate.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.17 no.4
• /
• pp.23-30
• /
• 1980

All the resistors in the active RC filter networks cab be replaced by the switched capaciters, The swiftched capacitor is much bet tar than a resistor in temperature and linearity characteristics, and the former can be fabricated on the much smaller silicon area than the latter. In this paper, it is given the generaliged design method of the active SC filter from the active RC filter using Bilinear Z-transformatirm. SC filtering techniques using Bilinear Z-transform enable us to realize the FDNR and Gyrator filters which could not be realized by the exsisting designs 1 and to utilize the processing of signals at much higher frequencies than the conventional design method. Experiments show that the response of the active SC filter is similiar to that of its prototype active RC filler.

• Transactions of the Korean hydrogen and new energy society
• /
• v.28 no.1
• /
• pp.92-97
• /
• 2017

Kerosene (Coal oil) is a particularly attractive fuel because it is widely used to power jet engines of aircraft as jet fuel and some rocket engine. This paper describes the performance and emission characteristics according to the collant temperature of combustion chamber head of spark ignition engine fuelled with kerosene. As a result, the following knowledge is obtained. As the collant temperature of combustion chamber head is decreased, torque, volumetric efficiency and brake specific fuel consumption have been increased. When coolant temperature of combustion chamber lower, THC emission increased but CO and $NO_x$ emission decreased.