• 한국융합학회논문지
• /
• 제9권1호
• /
• pp.283-289
• /
• 2018

자동차 디스크 브레이크시스템에서는 열유속 및 열변형 등과 같은 이유로 마찰열이 균일하게 분산되지 않는다. 마찰열에 의한 열탄성 변형이 접촉압력 분포에 영향을 미치게 되고, 접촉하중이 디스크 브레이크 표면상의 작은 영역에 집중되어 열탄성 불안정성을 초래 할 수 있다. 본 연구에서는 실험적 계산식과 Kao 제안한 디스크와 패드의 접촉압력에 대한 해석방법을 참고로 하여 3차원 축대칭 모델을 통하여 실제로 제동 시 발생되는 디스크와 패드의 접촉을 고려한 온도해석 및 열변형 해석을 하였다. ANSYS를 사용하여 디스크와 패드의 접촉면에서 발생하는 열탄성 불안전성 문제를 열하중과 기계적 하중으로 동시에 고려하여 해석하였다. 디스크와 패드가 직접 접촉하는 3차원 축대칭 모델을 구성하여 디스크의 마찰면 온도, 열변형, 접촉 열응력을 관찰함으로써 디스크에서 일어나는 열적 거동을 보다 정확하게 관찰하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 춘계학술대회논문집
• /
• pp.861-864
• /
• 2005

Brake noise has been one of the most difficult concerns in the automotive industry. Although substantial research has been conducted to predict and eliminate brake noise, there is yet no method to completely suppress brake noise. Furthermore, little effort has been made to improve noise and vibration characteristics of the railway brake system. The amount of sound energy radiated from the railway brake system is much larger than that from the automobile, and it causes discomfort of passengers in the station. In this paper, noise and vibration caused by the braking force of the KTX vehicle have been measured and analysed. Results show that noise level increases abruptly right before a train comes to a complete stop. Furthermore, typical characteristics of the disk brake squeal have been observed.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2003년도 추계학술대회 논문집(III)
• /
• pp.383-388
• /
• 2003

This study investigates the change of the temperature and mechanical properties of the braking disk for the railway vehicle. The average temperature is measured about $100^{\circ}C$ and the maximum temperature is measured over $200^{\circ}C$ by non-contact sensor from Seoul to Chunan. In the $20^{\circ}C-300^{\circ}C$, the $0.2\%$ offset yield strengths of the disk (GC25-30 material) are a little down to the reference value, but the linear relation of tensile test result is not find from the linear change of temperature. However, $J_{IC}$ values have the inverse proportion to the temperature, and the $J_{IC}$ value at $200^{\circ}C$ decrease $30.55\%$ from the $J_{IC}$. value of the room temperature. This result means that the crack length on the braking disk is rapidly increase at $200^{\circ}C$

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2006년도 추계학술대회 논문집
• /
• pp.274-280
• /
• 2006

The study is to analyze dynamo test results for various commercial pads in order to verify the performance of brake disk with CV-NCM cast iron. The developed brake disk will apply to 200 km/h tilting trains that is being developed as one part of project for speed-up on Korean existing railroad. The test program is made out suitably for braking condition and performance of test equipment by referring UIC 541-3. Two kinds of resin pad and one kind of foreign sintered pad suitable for 200 km/h trains are used as various commercial pad for the dynamo test. The data aquisition for the maximum and smallest temperature, hot spot, etc. on disk and pad is performed by using the thermocouples and thermal imaging cameras. From this research, we obtained braking characteristics between CV-NCM cast iron disk and pad of various material and will be utilized usefully as basis data of performance optimization of developing sintered pad.

• 한국철도학회논문집
• /
• 제10권3호
• /
• pp.251-256
• /
• 2007

The research analyzed dynamo test results to evaluate compatibility between brake disk made of NCM-CV cast iron and various pads. The dynamo test was executed with one kind of resin pad and three kinds of sintered pads suitable for 200 km/h trains according to a program which refers to UIC 541-3. The thermocouples were established in specific location in order to measure the temperature of disk and pads. In addition, the thermal imaging camera was used for capturing the instantaneous thermal characteristic of disk. The research results may be utilized to use as basis data of pad development for NCM-CV brake disk hereafter.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 추계학술대회 논문집
• /
• pp.1761-1765
• /
• 2008

In the braking of a railroad car, mechanical brake systems using wheel tread and brake disk are applied as well as electrical brake systems by regenerator and rheostat. It is very important to consider the frictional characteristic because kinetic energy of the vehicle is dissipated as converted thermal energy through friction between disk and brake pad during disk braking. A friction coefficient and wear characteristic are decided from the interrelationship of disk and friction material in the disk brake system. Lab-scale dynamometer test on developed brake disk materials for increasing heat resistance was performed in this study. Each candidate material was tested at various braking speeds and pressures and we obtained the friction coefficient and wear characteristic. And we executed comparative evaluation of the result from the test.

• 대한기계학회논문집A
• /
• 제35권4호
• /
• pp.425-431
• /
• 2011

차량 제동시 디스크와 패드사이의 미끄럼 접촉에 의해 발생하는 마찰열은 재질의 열 탄성 변형을 일으키고, 이는 접촉면의 압력 분포에 영향을 끼친다. 이러한 열탄성 불안정성 (Thermo-Elastic Instability, TEI)은 디스크의 고유 진동모드와 결합되어 열섬 현상 및 열간 저더 진동을 발생시킨다. 본 연구에서는 상용 유한 요소 해석 프로그램인 SAMCEF 를 이용하여 자동차용 통풍식 디스크에 대한 3 차원 열간 저더 해석을 수행하였다. Staggered approach 에 의거한 중간 처리기를 이용하여 구조-동역학 해석 결과와 열 전달 해석 결과를 교환하였다. 디스크 표면에 열섬이 발생하는 것을 확인하였고, 이를 디스크 고유 진동 모드와 비교함으로써 모드 형상과 열섬 분포의 관계를 분석하였다.

• Tribology and Lubricants
• /
• 제25권6호
• /
• pp.381-386
• /
• 2009

In general, a brake system of axle for heavy duty machine as a wheel excavator makes use of wettype multiple disk brakes. These disk bakes are very important parts of heavy duty machine because they are dvanced in durability and braking power, and can be designed compactly. Thus, we adesigned and made wettype multiple disk brakes of axle for the wheel excavator to be localization of these imported all. In this study, wet multiple disk brakes were made a comparative test with the 3 types materials of friction disk by the SAE No.2 dynamometer. The friction characteristics were measured and analyzed to decide a suitable material as wear depth of friction disk and dynamic and static friction coefficient on temperature of oil and applied pressure.

• 자동차안전학회지
• /
• 제7권2호
• /
• pp.19-24
• /
• 2015

Ferritic Nitro Carburizing (FNC) cast iron brake discs is known to improve corrosion resistance and brake creep groan noise as well as prevent corrosion-induced pulsation. But, it is necessary to treat honing machining on braking surface to avoid grinding noise during braking.

• Tribology and Lubricants
• /
• 제28권5호
• /
• pp.246-251
• /
• 2012

Disc brakes and brake linings are part of the braking system in automobiles; this system works due to the braking power between the disc and pad. Vehicle braking systems have complex environments due to the geometry of the disk and pad, the material properties, the braking conditions, etc. Braking energy is converted into thermal energy during the braking process, due to the frictional heat between the disc brake and pad. This heat is changed to a heat flux, which affects the thermal stress of the disc. The purpose of this study was to use the fluid dynamics software ANSYS CFX to investigate the inner flow characteristics of the air and the heat transfer of the disc, and to analyze the effects on the thermal stress of the disc brake.