• The Journal of the Korea institute of electronic communication sciences
• /
• v.17 no.3
• /
• pp.441-448
• /
• 2022

In the distribution system, there are multiple power protection systems such as circuit breakers at substations, and reclosers, minimum circuit ampacities, fault interrupters on distribution lines. They are widely used to prevent partial outages, cascading power failure or blackout so that other healthy systems could maintain the integrity in case of the instant fault or permanent failure on the power lines. However, when a fault happens, it could cause a major black out due to the lack of the protection cooperation between the protection relay of the circuit breaker at a substation and a protection system on the distribution lines. To achieve the power system integrity better, it is required to develop the circuit breaker which can be operational within 1 cycle(16ms). In this study, the high speed circuit breaker which is filled up with eco-friendly gas is developed. This equipment achieved an excellent test results based on IEC 62271-111 standard. It is respected that this equipment would contribute to prevent the wide area blackout by isolating a fault area quicker and faster.

• Proceedings of the Korea Air Pollution Research Association Conference
• /
• 2008.10a
• /
• pp.453-454
• /
• 2008

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2012.06a
• /
• pp.242-242
• /
• 2012

• 프린팅코리아
• /
• v.12 no.3
• /
• pp.92-93
• /
• 2013

작업량과 시간, 기계를 뛰어넘어 수만 번의 출력에도 일관적인 고품질의 인쇄를 유지하는 '오세 다이렉트 프레스' 는 사용자의 신뢰를 얻기에 충분하다. 가변 데이터 처리를 통해 기존 출력 방식의 LED, 정착 온도, 습도, 정전하, 디벨로퍼와 폐토너의 영향을 받지 않는 안정성과 컬이 없는 일관성 있는 출력품질은 오세의 타협 없는 자부심이 낳은 결과다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2011.06a
• /
• pp.1117-1118
• /
• 2011

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.10 no.3
• /
• pp.463-469
• /
• 2009

We performed the experimental study on the control of suspended dust in a cement packaging process for various ventilation systems. To effectively remove the dust generated in the cement packaging process, three different kinds of ventilation system, such as local exhaust ventilation, electrostatic scrubber, and local air supply system, were adopted. Dust concentrations in the packaging process were measured with the variation of the airflow rate of the ventilation systems and then their ventilation performance were evaluated. From the results, we knew that the ventilation performance was the best when the local exhaust ventilation and the electrostatic scrubber were simultaneously operated in the packaging process. In the electrostatic scrubber system, the effect of the airflow rate on the indoor dust removal efficiency was negligible so hat he system ust be operated at $2,700m^3/h$ for saving power consumption.

• KEPCO Journal on Electric Power and Energy
• /
• v.6 no.2
• /
• pp.173-179
• /
• 2020

Electric vehicles (EVs) using lithium secondary batteries (LIBs) with excellent power and long-term cycle performance are gaining interest as the successors of internal combustion engine (ICE) vehicles. However, there are few systematic researches for fast charging to satisfy customers' needs. In this study, we compare the degradation of LIB where its composition is LiNi_0.5Co_0.2Mn_0.3/Graphite with the constant current and constant power-charging method. The charging speed was set to 1C, 2C, 3C and 4C in the constant current mode and the value of constant power was calculated based on the energy at each charging speed. Therefore, by analyzing the battery degradation based on the same charging energy but different charging method; CP charging method can slow down the battery degradation at a high rate of 3C through the voltage curve, capacity retention and DC-IR. However, when the charging rate was increased by 4C or more, the deviation between the LIBs dominated the degradation than the charging method.

• Transactions of the KSME C: Technology and Education
• /
• v.2 no.1
• /
• pp.1-8
• /
• 2014

Recently vehicle development trend changes from machinery vehicle to the electrical and electronic devices. As well the electrical and electronic devices commercial vehicles are increasing more than machinery system. The capacitance fuel sensor is a sensor that, by measuring the capacitance value of fuel level sensor MCU operating for the final voltage value of the signal output. That is increasing durability and fuel measurement accuracy more than conventional ceramic resistor type. For Sensor software verification R-BENCH TOOL generated test case automatically. We make the programmable Capacitor board for test. And it was confirmed that more than 98% of the high reliability of the software.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.17 no.1
• /
• pp.71-76
• /
• 2022

Since brightness is proportional to the operating current, a method of connecting several LEDs in series and driving with a constant current source is widely used for driving circuits of LED lights. Because several LEDs are connected in series, if some LEDs open due to a fault, the current path is broken and all other LEDs connected in series are turned off. In this paper, we designed a circuit to solve this problem by connecting a Zener diode having a breakdown voltage of about 0.4V higher than the LED operating voltage in parallel with each LED to create a current bypass in case of LED failure. Through simulations and experiments, it was confirmed that the current of the Zener diode hardly flows when the LED is operating normally, and that the Zener diode stably operates as a current bypass when the LED fails.

• Annual Conference of KIPS
• /
• 2012.04a
• /
• pp.986-988
• /
• 2012

최적의 식물 생장을 위해서는 적절한 수분의 유지가 필수적이며 넓은 지역, 다양한 종류, 고가의 식물의 경우일수록 적절한 수분의 관리를 위한 시스템의 도움이 필요하다. 이를 위해 저가의 센서노드 시스템이 적절한 해결책이 될 수 있으나 일반적인 배터리 기반의 센서노드 시스템을 적용시 배터리 용량 확인 및 교체 등의 유지보수 문제가 대두된다. 본 논문에서는 이러한 유지보수의 문제를 해결하고 식물재배에 도움을 줄 수 있는 자기유지 지원 방식의 정전용량 센싱기반의 수분 모니터링 센서노드를 설계하였다. UHF 기반의 무선 전력 전송의 자기유지 지원 시스템 및 PCB 패턴기반의 정전용량센싱 수분센서와 초저전력 센서노드 시스템으로 구성된다. 센서노드는 한번 송신시 약 0.24 mJ을 소모하며 에너지획득모듈은 에너지 획득 주기마다 약 4 mJ의 에너지를 공급하도록 설계하여 센서동작을 위한 충분한 에너지 마진을 주도록 설계하였다.