• Tunnel and Underground Space
• /
• v.10 no.4
• /
• pp.533-543
• /
• 2000

Deformation behavior and stability of vertical pipeline subjected to underground excavation have been studied by means of numerical analysis. Vortical ground displacements cause the pipe to be compressed, while horizontal ones cause it to be bent. In that region the vertical pipeline meets with the induced compressive stress and bending stress. In addition horizontal rock stress subjected to underground excavation may press the tube in its radial direction and it finally produces the tangential stress of pipe. In this study active gas well system is considered as an example of vertical pipelines. Factor analysis has been conducted which has great influence on the pipeline behavior. Three case studies are investigated which have the different pillar widths and gas well locations in pillar. For example, where overburden depth is 237.5 m and thickness of coal seam is 2.5 m, chain pillar of 45.8 m width in the 3-entry longwall system is proved to maintain safely the outer casing of gas welt which is made of API-55 steel, 10$\frac{3}{4}$ in. diameter and 0.4 in. thickness. Finally an active gas well which was broken by longwall mining is analyzed, where the induced shear stress turn out to exceed the allowable stress of steel.

• Proceedings of the Korean Society of Dyers and Finishers Conference
• /
• 2012.03a
• /
• pp.86-86
• /
• 2012

고속방사소재는 연신공정이 없이 6,000m/min이상의 고속방사공정만이 있으므로 원가절감이 되고, 빠른 냉각, 높은 변형속도 등으로 섬유의 결정화도, 분자와 결정의 배향 및 모폴로지(morphology) 변화 등의 기계적 및 섬유상의 특성이 종래의 원사와는 다르게 된다. 방사속도가 증가함에 따라 배향도가 증가하면서 결정영역 또한 증가한다. 또한 기존 연신사에 비해 큰 결정크기를 갖는데 방사속도에 에 따른 방사응력의 증가가 응력유도 결정화도를 유발하여 결정크기 및 결정화도를 증가시키고,따라서 고분자의 용융점도를 고온측으로 이동시키는 현상을 나타내게 한다. 즉, 고속방사에 있어서는 연신에 필요한 임계응력 이상의 과도한 응력이 가해짐으로 인해 결정구조가 일반 연신사에 비해 현저히 발달한다는 것을 알 수 있다. 고속방사 원사를 통일한 조건으로 염색하는 경우 기존의 연신사보다 염착량이 많아 농색으로 염색이 가능하고 염착속도도 빠른 특징을 갖는 데이는 고속방사 원사의 비결정 배향이 낮고 느슨한 구조를 갖기 때문에 염료의 침투가 용이한 것으로 해석되고 있다. PET 섬유는 방사 후 형태안정성을 부여하기 위해서 염색 전처리 공정에서 열을 가하게 된다. 이런 과정에서 섬유의 미세구조가 변하게 되는데,특히 고속방사의 경우 섬유 형성과정이 연신사와는 다르므로 열에 의한 구조 변화와 이에 따른 염색성 변화에 대해 검토해 보는 것은 고속방사의 응용면에서 꼭 필요하다. 본 연구에서는 고속방사소재의 가장 단점인 잔류신도, 저수축현상, stiff감을 보완하면서 고속방사소재의 장점인 심색성을 부각시켜 차별화된 복합사 제조기술을 개발하기 위해 그 기술개발이 기초 연구로서 일반 일반 DTY사와 고속방사소재인 HOY사를 이용한 DTY사의 물성 및 염색 특성을 비교분석 하고자 한다.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.35 no.7
• /
• pp.601-611
• /
• 2007

Most of mechanically jointed aircraft structures are always encountered the fretting damages on the contact surfaces between two jointed structural members or at the edges of fastener holes. The partial slip and contact stresses associated with fretting contact can lead to severe reduction in service lifetime of aircraft structures. Thus a critical need exists for predicting fretting crack initiation in mechanically jointed aircraft structures, which requires characterizing both the near-surface mechanics and intimate relationship with fretting parameters. In this point of view, a series of fretting fatigue specimen tests for 2024-T351 Al-alloy, have been conducted to validate a mechanics-based model for predicting fretting fatigue life. And included in this investigaion were elasto-plastic contact stress analyses using commercial FEA code to quantify the stress and strain fields in subsurface to evaluate the fretting fatigue crack initiation.

• Journal of the Korea Concrete Institute
• /
• v.19 no.3
• /
• pp.253-263
• /
• 2007

Previous researches showed that confined concrete with Fiber-Reinforced Plastic (FRP) sheets significantly improves the strength and ductility of concrete compared with unconfined concrete. However, the retrofit design of concrete with FRP materials requires an accurate estimate of the performance enhancement due to the confinement mechanism. The object of this research is to predict the compressive strength and strain of concrete confined with FRP wraps. For the purpose of this research, 102 test specimens were fabricated and loaded statically under uniaxial compression. Axial load, axial and lateral strains were investigated to predict the ultimate stress and strain. Also, to achieve reliability of proposed strength and strain models for FRP-confined concrete, another series of uniaxial compression test results were used. This paper presents strength and strain models for FRP-confined concrete. The proposed models to estimate the ultimate stresses and failure strains produce satisfactory predictions as compared to current design equations. In conclusion, it is proposed that the modified stress-strain model of concrete cylinders could be effectively used for the repair and retrofit of concrete columns.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.34 no.1
• /
• pp.53-59
• /
• 2014

Because a molten steel carrier is used in high-temperature and corrosive environments, erosion and corrosion decrease the thickness of the structure and expand the vent hole for emitting gas generated from refractory bricks. This increases the stress throughout the structure and introduces a significant stress concentration around the vent hole. In addition, the high-temperature environment degrades mechanical properties such as the yield and tensile strengths. These problems seriously affect the safety of the structure. In this study, the safety of a 10-year-old structure was evaluated by analyzing the stress distribution and measuring the mechanical properties of the structure. The mechanical properties were directly measured on the structure surface using the instrument indentation technique.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.17 no.4
• /
• pp.365-374
• /
• 2004

Steel bridges, which have been damaged by load and corrosion, need repair or strengthening. That is a cause of decreasing the durability of structure. In order to solve these problems, welding repair and strengthening methods can be considered. In general, cutting and welding procedure is carried out during the repair welding. Therefore, the investigation of the behavior of residual stress and deformation generated by cutting and welding is very important for safety of structure. Residual stress and deformation produced by gas cutting and arc welding were analyzed using 2D and 3D thermal elasto-plastic FEM. According to the results, the magnitude of temperature was analyzed by 2D-FEM is smaller than that was analyzed using the 3D-FEM at the start and end edge of flange. And the magnitude and distribution of residual stress of perpendicular direction of the cutting line and welding line was analyzed by the 2D-FEM was similar to that was analyzed by 3D-FEM. Therefore, it is possible to predict cutting and welding residual stress by 2D and 3D FEM.

• Korean Journal of Materials Research
• /
• v.8 no.12
• /
• pp.1121-1126
• /
• 1998

For vacuum seated panel, stresses and displacements in the glass plate were calculated. The geometric variables for our experiment were the thickness of glass plate, the size of panel and the width of sealing line. The fracture behaviors and displacements of its under the vacuum were measured. From the measurement of strains and fracture, it was considered that the maximum stress acted at the middle of the sides of the panel. The stresses and displacement distribution of manufactured panels were greatly dependent on the width of the sealing line in the panel. The measured values are more similar to the values which were calculated from the condition of built-in edge as the width of the sealing line is larger. The measured displacement of the panel, made of 3mm thick glass plate, with size of $80\Times120\textrm{mm}^2$ and 20mm sealing line was $57\mu\textrm{m}$. This value is similar to calculated value, $54\mu\textrm{m}$, from built- in edge condition in the finite element method.

• Journal of the Microelectronics and Packaging Society
• /
• v.20 no.1
• /
• pp.21-26
• /
• 2013

This study presents new analysis method to predict bending behavior of packaging substrate structure by comparing finite element method simulation and measured curvature using 3D scanner. Packaging substrate is easily bent and deflected while undergoing various processes such as curing of prepreg and copper pattern plating. We prepare specimens with various conditions and measure contours of each specimen and compute the residual stresses on deposited films using analytical solution to find the principle of bending. Core and prepreg in packaging substrate are made up of resin and bundles of fiber which exist orthogonally each other. Anisotropic material properties cause peculiar bending behavior of packaging substrate. We simulate the bending deflection with finite element method and verify the simulated deflection with measured data. The plating stress of electrodeposited copper is about 58 MPa. The curing stresses of solder resist and prepreg are about 13 MPa and 6.4 MPa respectively in room temperature.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.12
• /
• pp.1541-1546
• /
• 2013

The stress concentration of lock-claws, which are one of the important parts for pneumatic fitting for a flexible tube connection, was investigated by finite element simulation. In this study, the generation of the local plastic deformation was predicted when the tube was hooked up to a pneumatic fitting in order to disperse the stress concentration, and design optimization was carried out using the Taguchi method. For the optimization, the outer width, bending angle, and inner radius of the lock-claws are used as main variables. As a result, their respective contribution ratios are revealed as 81.3%, 10.9%, and 1.5%. The ratio of the total stress distribution was improved by 4% compared with the initial design of the lock-claws.

• Korean Journal of Food Science and Technology
• /
• v.19 no.4
• /
• pp.366-370
• /
• 1987

Rheological properties of gelatinized rice starch solutions (5%) were examined with a Brookifield viscometer. Gelatinized rice starch solutions showed pseudoplastic flow having yield stress, i.e., Binghamplastic flow behavior. The yield stress of gelatinized rice starch solutions was reduced by the phosphate. Phosphate increased the pseudoplasticity of gelatinized nonwaxy rice starch solutions. but decreased that of gelatinized waxy rice starch solution. The yield stress of gelatinized nonwaxy rice starch solutions held for one hour at $90^{\circ}C$ was slightly decreased, but that of waxy starch solution was reduced by 10-fold. Phosphate reduced the yield stress for both gelatinized nonwaxy and waxy rice starch solutions. Phosphate decreased the consistency index, but did not affect the flow behavior index of the gelatinized rice starch solutions.