• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 1995.10a
• /
• pp.160-164
• /
• 1995

정보통신 시스템의 고속/고밀도화 요구에 따라 개발되고 있는 ATM(Asynchronous Transfer Mode) 교환기 시스템은 팬을 이용한 강제대류냉각 방식의 채택과 시스템이 설치되는 장소에 따른 여러 환경조건에 의한 진동 문제가 발생될 수 있다. 시스템의 진동으로 인한 피해중 커넥터 접촉부에서 전기적 특성의 변화는 고속으로 전송되는 신호의 왜곡을 유발시킬 수 있어 시스템 개발시 이에 대한 충분한 연구 및 시험이 요구되고 있다. 진동환경에서 커넥터 접촉부는 접촉면의 상대운동으로 인한 접촉저항의 증가와 순간적인 신호전달 중단을 가져오게 되며, 특히 PCB/Connector Assembly에서 커넥터 접촉부는 PCB(Printed Circuit Board)의 장착 조건 및 동적 거동에 따라 전기적 특성이 변할 수 있다. 시스템에서 커넥터의 동적 거동을 이해하기 위해서는 PCB를 포함하는 시스템내 여러 요소의 동적 특성 이해와 복잡한 해석과정이 요구되며, 시스템 개발자는 진동 환경에서 이것의 시험 결과에 따라 커넥터의 사용을 결정해야 할 것이다. 커넥터의 전기적 특성 시험법은 IEC, EIA드 여러 국제 규격에 제시되어 있으며, 본 연구의 대상이 된 ATM교환기 시스템에서 PCB/Connector Assembly의 진동환경에서 접촉저항 측정과 관련된 접촉저항 임계치 및 측정법은 IEEE 규격 및 Bellcore 규격에 규정되어 있다. Bellcore에는 주어진 진동시험주기 전후에 IEC 규격의 LLCR(Low Level Contact Resistance) 측정회로를 이용한 측정법이 규정되어 있고, 냉각팬 및 주위 환경진동이 가해지는 동안의 영향에 대한 시험법은 규정되어 있지 않다. 본 연구에서는 한국통신의 전자장비 운용환경시험 조건의 진동에서 ATM 교환기 시스템에 사용되는 PCB/Connector Assembly 커넥터 접촉부의 접촉저항 변화와 PCB 진동에 의한 영향을 시험하였다.proach)등이 제시되었고 평면파 영역에 한하여 해서되어져 왔다. 본 논문에서는 분할 접근 방법(Segmentation Approach)을 이용하여 다공 요소로 이루어진 소음기를 해석하는데 적용하였다.로 성능 및 안정도에 영향을 미치므로 주의 깊게 선정해야 한다. 방법의 실질적인 적용에는 어려움이 있다. 본 연구에서는 기존의 방법들의 단점을 극복할 수 있는 새로운 회귀적 모우드 변수 규명 방법을 개발하였다. 이는 Fassois와 Lee가 ARMAX모델의 계수를 효율적으로 추정하기 위하여 개발한 뱉치방법인 Suboptimum Maximum Likelihood 방법[5]를 기초로 하여 개발하였다. 개발된 방법의 장점은 응답 신호에 유색잡음이 존재하여도 모우드 변수들을 항상 정확하게 구할 수 있으며, 또한 알고리즘의 안정성이 보장된 것이다.. 여기서는 실험실 수준의 평 판모델을 제작하고 실제 현장에서 이루어질 수 있는 진동제어 구조물에 대 한 동적실험 및 FRS를 수행하는 과정과 동일하게 따름으로써 실제 발생할 수 있는 오차나 error를 실험실내의 차원에서 파악하여 진동원을 있는 구조 물에 대한 진동제어기술을 보유하고자 한다. 이용한 해마의 부피측정은 해마경화증 환자의 진단에 있어 육안적인 MR 진단이 어려운 제한된 경우에만 실제적 도움을 줄 수 있는 보조적인 방법으로 생각된다.ofile whereas relaxivity at high field is not affected by τS. On the other hand, the change in τV does not affect low field profile but strongly in fluences on both inflection fie이 and the maximum relaxivity value. The results shows a fluences on both inflection field and the maximum relaxivity v

• Journal of the Korean Society of Radiology
• /
• v.11 no.2
• /
• pp.79-85
• /
• 2017

The purpose of this study is to investigate the cause analysis according to the difference between the pre exposure tube voltage and actual exposure tube voltage in mammography in connection with breast pressure thickness, breast size and body mass index and to find the improvement. The study tracked 377 women age 40 and older among the mammography examiners conducted by the National Health Insurance Corporation. It was analyzed that breast pressure thickness, breast size and body mass index according to the difference between the pre exposure tube voltage and actual exposure tube voltage among the parameters of dose report been sent to the picture archiving communication system with reference to the image with cranio-caudal projection in mammography. As are result, it shows that the thicker the breast thickness, smaller the breast size and lower body mass index, the higher the difference of tube voltage. In conclusion, the minimum tube voltage of mammography machine should be reset in order to set the tube voltage according to breast pressure thickness and breast size that are suitable for our country in mammography, in addition, it was considered that radiologist should make an effort to reduce radiation exposure and make a good quality image with reducing the difference of mammography condition by making a correct exposure condition in case of examining the patients with thin breast pressure and small breast size.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.16 no.1
• /
• pp.199-207
• /
• 2016

In this paper, we propose efficient smart indoor emotional lighting control system based on android platform using the biological signal. The proposed smart indoor smart emotional lighting control system were configured as the biological signal measurement device and removable smart wall pad, lighting driver, luminaire. The control system was extracts the emotional language by measured the biological signal, and it was transmitted a control signal to each lighting driver using a bluetooth in the wall pad. The lighting driver were designed to control the lighting device through an expansion board by collected control signal and the illuminance information the surrounding. In this case, the wall pad can be selecting of manual control and the bio signal mode by that indoor emotional lighting control algorithms, and it was implemented the control program that possible to partial control by selecting the wanted light. Experiment results of the proposed smart indoor emotional lighting control system, it were possible to the optional control about the luminaire of required area, and the manual control by to adjustable of color temperature with that the efficiently adjustable of lighting by to biological signal and emotional language. Therefore, were possible to effective control for improvement of concentration and business capability of indoor space business conduct by controlling the color and brightness that is appropriate for your situation. And, was reduced power consumption and dimmer voltage, lighting-current than the existing-emotional lighting control system.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.12
• /
• pp.10-21
• /
• 2015

Cellular Network assisted device-to-device (D2D) communication has been growing to reduce the overload of eNodeB and mitigate the frequency shortage. However, by sharing the uplink frequency resource with the cellular network, the interference between cellular and D2D is increased. In this paper, we propose the advanced receiver based on soft decision to reduce the interference between cellular and D2D. The proposed receiver can suppress and cancel the interference by calculating the unbiased estimation value of interference signal using minimum mean square error (MMSE) or interference rejection combing (IRC) receiver. The interference signal is updated using soft information expressed by log-likelihood ratio (LLR). We perform a system level simulation based on the 20-MHz bandwidth of the 3GPP LTE-A system. Simulation results show that the proposed receiver can improve SINR, throughput and spectral efficiency compared to conventional receivers.

• Journal of Advanced Navigation Technology
• /
• v.18 no.1
• /
• pp.84-89
• /
• 2014

Worldwide Interoperability for Microwave Access (WiMAX) is an efficient technology for 20th century communication system. The technology provides broadband speed without the need for cables and is based on the IEEE 802.16 standard(also called Wireless MAN). Mobile WiMAX is defined as IEEE802.16e which is advanced and efficient technology for mobile telecommunication rather than GSM, CDMA technology. In this work link budget calculation for WiMAX have been done. Cell range have been calculated over digital modulations and they are BPSK, QPSK and QAM. Here different types of models like Cost 231 model have been used for different types of areas like open, rural and urban areas and Erceg-Greenstein model for sub-urban areas. Effect of various parameters like frequency, base station antenna height, transmission power and SNR over cell range have been studied. Analysis have done for both uplink and downlink.

• Journal of Advanced Navigation Technology
• /
• v.13 no.6
• /
• pp.916-925
• /
• 2009

4S (Ship to Ship, Ship to Shore) communication is the key to strategic development of e-navigation, a core element of IT vessel convergence. 4S communication is intended to integrate and standardize various communication infrastructures on land and communication equipment complying with communication equipment equipped in ships. This paper aims to apply the Korean technology IEEE 802.16e adopted as an international standard, to replace and compensate for existing vessel communication media such as low speed HF/MF/VHF to the ocean environment. To this end, various experimental conditions between the coast station where a relay station was installed and related equipment equipped on a ship are set. Communication signals were monitored and the RSSI and CINR were measured. Based on experimental analysis and results, various challenges and solutions which may occur in ocean environment were sought, and communication availability was analyzed through transmission data throughput, at the maximum effective distance range of the signal. It was proven that high speed multimedia data could be exchanged for up to 20 km even among 80km kph ships moving around near the sea, ensuring that this technology could be applied to the ocean environment.

• Journal of Advanced Navigation Technology
• /
• v.22 no.5
• /
• pp.400-408
• /
• 2018

Wide area augmentation system is a system that generates and transmits correction and Integrity information for use in wide area. Typical system is SBAS. In the United States, it operates under the name WAAS, EGNOS in Europe, MSAS in Japan, SDCM in Russia, GAGAN in India. it is developing Korean SBAS which named KASS by 2022 in Korea. SBAS is a standard System that is operated as civil aviation service base and set as international standards by ICAO. So the correction data can only is used for civil SPS receiver. In this paper, we discuss C1P1 DCB estimation which need to use SPS correction service for PPS receiver. Then we analyze C1P1 DCB correction effect under standalone Satellite Navigation and method to use PPS receiver under SPS DGPS. Finally we organize wide area augmentation system for PPS receiver and analysis performance.

• Journal of Navigation and Port Research
• /
• v.33 no.10
• /
• pp.691-697
• /
• 2009

Hardware dedicated off-the-shelf maritime differential GPS RSIM lacks the open architecture to meet all the minimum maritime user requirements and to include future GNSS improvements after recapitalization. This paper carries out a study to replace existing hardware dedicated differential GPS RSIM with software differential GPS RSIM in order to make up the weak point of hardware dedicated off-the-shelf maritime differential GPS RSIM. In this paper, the architecture of software RSIM is proposed for maritime DGPS recapitalization. And the feasibility analysis of the proposed software differential GPS RSIM is performed as the first phase to realize the proposed architecture. For the feasibility analysis, the prototype RF module and DSP module are implemented with properties as wide RF bandwidth, high sampling frequency, and high speed transmission interface. This paper shows that the proposed architecture has the possibility of real time operation of software RSIM functionality onto the PC-based platform through the analysis of computation time. Finally, this paper verifies that the L1/L2 dual frequency software differential RSIM designed according to the proposed method satisfies the performance specifications set out in RTCM paper 221-2006-SC104-STD.

• Journal of Broadcast Engineering
• /
• v.17 no.4
• /
• pp.695-706
• /
• 2012

The purpose of this paper is to propose a service system for a digital hologram video, which has not been published yet. This system assumes the existing service frame for 2-dimensional or 3-dimensional image/video, which includes data acquisition, processing, transmission, reception, and reconstruction. This system also includes the function to service the digital hologram at the viewer's view point by tracking the viewer's face. For this function, the image information at the virtual view point corresponding to the viewer's view point is generated to get the corresponding hologram. Here in this paper, only a prototype that includes major functions of it is implemented, which includes camera system for data acquisition, camera calibration and image rectification, depth/intensity image enhancement, intermediate view generation, digital hologram generation, and holographic image reconstruction by both simulation and optical apparatus. The proposed prototype system was implemented and the result showed that it takes about 352ms to generate one frame of digital hologram and reconstruct the image by simulation, or 183ms to reconstruct image by optical apparatus instead of simulation.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.8
• /
• pp.1507-1514
• /
• 2015

Non-orthogonal multiple access (NOMA) is a promising candidate for 5G networks. NOMA achieves superior spectral efficiency than conventional orthogonal multiple access (OMA), as in NOMA multiple users uses the same time and frequency resources. Multiple-input-multiple-output (MIMO) is one another promising technique that can enhance system performance. In this paper we present a spectral and energy efficient multiple antenna based NOMA scheme, known as spatially modulated NOMA. In the proposed scheme the cell edge users are multiplexed in spatial domain, which means the information to cell edge users is conveyed using the transmit antenna indices. In NOMA the performance of cell edge users are deeply effected as it treats signals of others as noise. The proposed scheme achieves superior spectral efficiency than the conventional NOMA. The number of decoding steps involved in decoding NOMA signal reduces by one as cell edge user is multiplexed in spatial domain. The proposed scheme is more energy efficient as compare to conventional NOMA. All of the three gains high spectral, energy efficiency and one step reduction in decoding comes at cost of multiple transmit antennas at base station.