• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1993.10a
• /
• pp.556-560
• /
• 1993

최근 모든 산업에 있어서 자동화에 대한 요구가 높아지고 있다. 모든 자동화는 힘들고 어려운 작업을 기계가 인간을 대신하여 수행하며 품질 및 생산성을 향상시킨다는 관점에서 끊임없이 추구되고 있다. 용접 자동화도 그 예외는 아니어서 용접 구조물 제작의 경우, 임의의 용접 경로를 추적하는 방법과 공정 변수의 제어법 등이 현재 연구되고 있다. 특히 용접 공정중 용접선 경로 변화를 측정할 수 있는 센서가 용접 공정의 자동화에 필수적이다. 이러한 센서중에는 아크센서, 시각센서, 초음파센서, 레이저센서가 있으며, 이중 널리 이용되고 있는 것은 팁-모재간의 거리변화에 따른 전류 또는 전압 변화를 모델링하여 위치 정보로 이용하는 아크센서와, 카메라를 이용한 영상 정보를 처리함으로써 토치가 이동해야 항 위치를 찾는 시각센서가 있다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.166-166
• /
• 2004

운전자 보조시스템에는 적응순항제어 (adaptive cruise control), 차선변경 (lane change), 충돌경고 (collision warning), 충돌회피 (collision avoidance), 및 자동주차 (automatic parking) 등이 있다. 이런 운전자 보조시스템은 어떤 목적을 가지고 있다. 운전자의 부담을 줄이고 안전을 위하여 차량의 주행방향에 있는 장애물이나 차량을 감지하여 차량간의 안전거리론 유지하고 자동차가 일정 속도를 유지하도록 한다. 운전자 보조시스템의 효율은 센서들로부터 얻어진 정보의 해석에 달려있다.(중략)

• Journal of the Korean Society for Precision Engineering
• /
• v.17 no.1
• /
• pp.45-51
• /
• 2000

In this Paper a basic technique of gantry robot control system has been developed to weld the curved part of a large structure. A welding robot is designed to rotate torch and make the torch angle normal to the welding surface. The Kalman filter is applied to obtain the smooth welding path signal from the noised Sensing data. A welding path finding algorithm has been developed in Turbo-C language.

• Journal of the Korean Society for Precision Engineering
• /
• v.31 no.1
• /
• pp.51-57
• /
• 2014

This paper presents a synchronizing adaptive feedforward control for clamping servomechanism of injection molding machines. Based on MBS, virtual design model has been developed for a direct forcing clamping mechanism. A synchronizing controller is designed and combined with adaptive feedforward control to accommodate mismatches between the real plant and the linear plant model used. From tracking control simulations, it is shown that significant reduction in position tracking error is achieved through the use of proposed control scheme.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.6
• /
• pp.176-182
• /
• 1999

In this paper, we consider a decoupling control and a servo control for the JINAMCHA of which the cart and the pointer is coupled very strongly. The right eigenstructure assignment(i.e. simultaneous assignment of eigenvalues and right eigenvectors) is used for decoupling the motions of the cart and the pointer. The CGT(Command Generator Tracker) is used for a servo control of the JINAMCHA. The performance of the proposed control scheme, that is the combination of the right eigenstructure assignment and the CGT, is evaluated by simulations. The results show that the proposed controller has better performance than the LQR with limiting properties and the conventional LQ servo.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.1105-1109
• /
• 1995

A CCD-camera, which is structured with vision system, was used to realize automatic seam-tracking system and 3-D information which is needed to generate torch path, was obtained by using laser-slip beam. To extract laser strip and obtain welding-specific point, Adaptive Hough-transformation was used. Although the basic Hough transformation takes too much time to process image on line, it has a tendency to be robust to the noises as like spatter. For that reson, it was complemented with Adaptive Hough transformation to have an on-line processing ability for scanning a welding-specific point. the dead zone,where the sensing of weld line is impossible, is eliminated by rotating the camera with its rotating axis centered at welding torch. The camera angle is controlled so as to get the minimum image data for the sensing of weld line, hence the image processing time is reduced. The fuzzy controller is adapted to control the camera angle.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.664-669
• /
• 2003

This paper proposes a swing-arm type dual-stage actuator, which consists of a PZT actuator for fine motion and a VCM(Voice Coil Motor) for coarse motion, for SFF ODD(Small Form Factor Optical Disk Drive), in order to achieve fast access speed and precise track following control. We focus our attention on the design and control of the PZT actuator, because there have been a lot of previous researches related to the VCM and dual-stage actuators. Due to the dual cantilever structure, the PZT actuator can generate precise translational tracking motion at its tip where optical pickup is attached at, and the effect of hysteric behavior of the PZT element is reduced. The dynamic model of the PZT actuator is derived by using the Hamilton's principle, and verified by comparing with the experimental frequency response. The sliding mode control is designed in order to be robust against modeling uncertainties. Simulations and experimental results confirm the effectiveness of the suggested control scheme.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.1
• /
• pp.26-34
• /
• 1998

In this paper, a force control algorithm for edge following task is suggested. Through the contact state modeling between rigid part and end-effector of robot, contact force and contact angle that are essencial parameters to build the control strategies for following movement of end-effector are derived. From these two parameters, we discriminate the every contact state into 8 cases and calculate the new moving position and direction simply. For the experiment. RX90 robot from Staubli with robot language V$^{+}$ is applied and F/T sensor is attached to the wrist of robot with RCC. Finally, 3 edge following experiments including the following of corner point are executed with successful results.s.

• Journal of the Korean Society for Precision Engineering
• /
• v.21 no.11
• /
• pp.83-90
• /
• 2004

In this paper we present a new real-time visual servoing unit for laparoscopic surgery This unit can automatically control laparoscope manipulator through visual tracking of laparoscopic surgical tool. For the tracking, we present two-stage adaptive CONDENSATION(conditional density propagation) algorithm to extract the accurate position of the surgical tool tip from a surgical image sequence in real-time. This algorithm can be adaptable to abrupt change of laparoscope illumination. For the control, we present virtual damper system to control a laparoscope manipulator safely and stably. This system causes the laparoscope to move under constraint of the virtual dampers which are linked to the four sides of image. The visual servoing unit operates the manipulator in real-time with locating the surgical tool in the center of image. The experimental results show that the proposed visual tracking algorithm is highly robust and the controlled manipulator can present stable view with safe.

• Journal of the Korean Society for Precision Engineering
• /
• v.10 no.4
• /
• pp.73-80
• /
• 1993

There and two important variables in machining process control, which are feed and cutting speed. It is possible to improve the machining accuracy and the productivity by maintaining the optimal feed and cutting speed. In this work, a controller is designed to achieve on-line cutting force control based on the modeling of cutting process dynamics established through step response test. Two schemes are proposed and implemented. The first is feed control under the constant spindle speed and the second is spindle speed control under the constant feed. Finally, both are proved to work properly through simulation and experimentation.