• Journal of the Korean Institute of Gas
• /
• v.12 no.2
• /
• pp.92-98
• /
• 2008

A combination of the instrumented indentation and 3D morphology measurement has been tried in order to perform a real-time property measurement of degraded materials in gas pipelines; three-dimensional indent morphologies were recorded using a reflective laser scanner after a series of insturmented indentations on three metallic specimens. Dimensions of the permanent deformation zone and contact boundary were analyzed from the cross-sectional profile over an remnant indent and used for estimating yield strength and hardness, respectively. Estimated yield strength was comparable with that from uniaxial tensile test and actual hardness implying material pile-up effects was lower than the calculated value from indentation curve by $20{\sim}30%$. It means that this 3D image analysis can explain the material pile-up effects on the contact properties. Additionally, a combined system of indentation and laser sensor was newly designed by modifying a shape of the indentation loading fixture.

• Journal of the Korean Society of Radiology
• /
• v.17 no.2
• /
• pp.175-184
• /
• 2023

Based on the actual shape of the detector and the data provided by the manufacturer, the shape of the detector was implemented through Penelope simulation and applied to the appropriate four-layer thickness based on the efficiency obtained from the measurements. Efficiency calculations to determine the effect of the simulated number of Full Energy Peak Efficiency(FEPE) channels in the detector and the outside contact layer in the crystal on the Full Energy Peak Efficiency were performed for various four-layer thicknesses of 0.3, 0.5, 0.7, 1.0, 1.2, and 1.4 mm using the Penelope Code. When the thickness of the external contact layer was increased by 5 times, the Full Energy Peak Efficiency decreased by about 36% for 59.50 keV, and the Full Energy Peak Efficiency decreased by 10% for 1836. In addition, as it increased by 10 times, the Full Energy Peak Efficiency decreased by about 20% for 59.54 keV, and 7% for 1836.01 keV. The Penelope simulated Full Energy Peak Efficiency channel decreases exponentially with the increase in the four layers. In addition, it was confirmed that the total effect curve was well matched with a relative difference of less than 3.5% in the 0.3-1.4 mm dead layer thickness region. However, it was found that the inhomogeneous dead layer is still a parameter in the Monte Carlo model.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.33 no.2
• /
• pp.129-137
• /
• 2013

A force calibration of a nanoindenter and a 3D morphology observation of indenters were carried out in this study. A microbalance calibrated with standard weights was used for measuring the loads generated by a nanoindenter. The indentation load could be calibrated from the ratio of measured and generated loads and the first contact load also could be detected from the microbalance data. By analyzing atomic force microscopy images of two indenters, curvature radii of apexes were determined by $19.71{\pm}3.03$ and $1043.94{\pm}50.91$ nm, respectively, for the nearly new indenter A and the severly worn indenter B. Corresponding bluntness depths were estimated by 1.22 and 64.56 nm for the both indenters by overlapping their profiles on the perfect pyramidal shape. In addition, nanoindentation curves obtained from a fused silica reference material with the both indenters showed a depth difference corresponding to the bluntness depth difference along the indentation depth axis. By shifting amounts of the bluntness depths along the horizontal axis, whole nanoindentation curves overlapped on themselves and resulted in nanohardness values consistent within 1.11 % without considering the complex indenter area function of each indenter.

• Journal of the Korean Society for Nondestructive Testing
• /
• v.36 no.4
• /
• pp.266-272
• /
• 2016

This paper presents the investigation of the propagation behavior of bulk longitudinal waves generated by an ultrafast laser system in thin films. A train of femtosecond laser pulses was focused onto the surface of a 150-nm thick metallic (chromium or aluminum) film on a silicon substrate to excite elastic waves, and the change in thermoreflectance at the spot was monitored to detect the arrival of echoes from the film/substrate interface. The experimental results show that the film material characteristics such as the wave velocity and Young's modulus can be evaluated through curve-fitting in numerical solutions. The material properties of nanoscale thin films are difficult to measure using conventional techniques. Therefore, this research provides an effective method for the nondestructive characterization of nanomaterials.

• 한국신재생에너지학회:학술대회논문집
• /
• 2011.05a
• /
• pp.123.2-123.2
• /
• 2011

$ALU^+$ 태양전지는 PN접합을 후면에서 즉, Al을 소성하여 형성시키기 때문에 얼마나 균일하고 두껍게 형성하는 것이 가장 중요하다. 소성(Firing)은 태양전지 제조 과정에서 후면의 접촉을 위한 중요한 공정이다. 본 연구에서는 상업화가 가능한 n-type $ALU^+$ Emitter 태양전지에서 소성 횟수에 따른 특성을 연구 하였다. $ALU^+$ emitter 형성의 최적화를 위해 소성온도를 가변하고, 최적화된 온도에서 소성 횟수에 따른 DIV 측정을 통해 셀을 분석 하였다. 소성 횟수는 1~3회로 하였고, 그 결과 단락전류 밀도(Jsc)가 33.57mA/$cm^2$로 처음보다 15.1%증가 하였고, 곡선인자(Fill Factor)는 3회에서 66.04%로 218%증가 하였다. Al을 짧은 시간 안에 소성을 시키므로 해서 후면의 $P^+$ Emitter가 균일하게 형성되었기 때문에 개방전압(Voc)의 증가를 확인하였다. 본 연구를 통해 $ALU^+$ 태양전지의 후면 Aluminium 소성 조건의 최적화를 통하여 $ALU^+$ emitter가 충분히 형성되지 못하면 누설전류가 발생되고 직렬저항(Rs)이 크게 증가하여 개방전압(Voc) 및 단락전류밀도(Jsc)의 감소가 발생하게 되고, 직렬저항(Rs)의 증가와 병렬저항(Rsh)의 감소는 Fill Factor의 급격한 감소를 초래하게 됨을 알 수 있다. 이를 개선하면 태양전지 효율을 상승시키는 결과를 얻을 수 있음을 확인하였다.

• Analytical Science and Technology
• /
• v.7 no.2
• /
• pp.155-164
• /
• 1994

A conventional Grimm-type glow discharge source was constructed and applied to radio-frequency(13.56MHz) discharge for metal and ceramic analysis. We investigated the emission spectrum for aluminium and aluminium oxide and the influence of discharge operating paramaters including argon pressure, rf-power and DC-bias voltages at the sample-side electrode. Scanning Electron Microscope(SEM) also was used to investigate the effect of rf-sputtering on the microstructure formation of the aluminium oxide. Linear analytical calibration curves were constructed for Manganese and zinc element in samples of low alloy steel(BAS 401-405) and brass(NIST 1108-1117).

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.5 no.1
• /
• pp.144-149
• /
• 2001

There are many types of seam tracking methods actually used in industrial spot. Lately, Non-contact sensor technics are mostly used because non-contact sensor has more advantage than contact sensor in many parts. This paper also concerned about fiber sensor a kind of non-contact sensor. X-Y robot and fiber sensor scan the seam tracking to be weld. After scanning, X-Y robot moves the first working point of being scanned and welding starts automatically. It makes an experiment on some types of Seam tracking like straight line tracking, leaned line tracking and curved line tracking to confirm how well the fibers sensor tracks the seam pass to be weld. And the seam pass that had been tracked was welded by inverter $CO_2$ voiding machine.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2000.10a
• /
• pp.558-561
• /
• 2000

There are many types of seam tracking methods actually used in industrial spot. Lately, Non-contact sensor technics are mostly used because non-contact sensor has more advantage than contact sensor in many parts. This paper also concerned about fiber sensor a kind of non-contact sensor. X-Y robot and fiber sensor scan the seam tracking to be weld. After scanning, X-Y robot moves the first working point of being scanned and welding starts automatically. It makes an experiment on some types of Seam tracking like straight line tracking, leaned line tracking and curved line tracking to confirm how well the fibers sensor tracks the seam pass to be weld. And the seam pass that had been tracked was welded by inverter CO2 welding machine.

• Journal of the Korean Society for Railway
• /
• v.11 no.1
• /
• pp.33-38
• /
• 2008

To reduce the cost and time of transport in Eurasian railroad networks such as TKR, TCR and TSR owing to the problem of different track gauges (narrow/standard/broad gauge), it is important to develop the gauge-adjustable wheelset system to adapt easily to these gauges. Moreover, freight trains having the gauge-adjustable wheelsets should be passing various curved tracks in railroad networks. Therefore, to assure the safety of the gauge-adjustment whellset system, it is necessary to evaluate integrity of locking parts in the system using stress analysis. This study is focused on analyzing contact stress of locking parts by using FEA(finite element analysis) simulation during the gauge changeover operation and freight trains' service in the curved track, respectively.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.19 no.5
• /
• pp.38-44
• /
• 2020

Surface texturing of micro-dimples has been used in many manufacturing industries to reduce friction between two sliding contacted surfaces. Surface texturing decreases the frictional force owing to minimizing of the sliding contact area. In this paper, micro-dimples have been fabricated on an Al6061-T6 surface using a two-frequency elliptical vibration texturing (TFEVT) method. A high-frequency of 18 kHz and low-frequency of 250 Hz were applied to an elliptically-vibrated tool holder. The Stribeck curve was plotted to analyze the friction coefficient trends. Furthermore, the representative wetting index, such as the water contact angle (WCA), was measured by considering the friction coefficient. WCA is associated with micro-dimple density and associated parameters. Consequently, the dimpled surfaces with a low friction coefficient exhibited a relatively high WCA in the feed direction. According to the Stribeck curve, the dimpled surfaces demonstrate superior friction performance for mixed-film lubrication compared to the non-textured surface.