Kim, Jin-Hwan;Choe, Hyeon-Gwang;Kim, Jong-Yeol;Im, Gi-Hong;Jeon, Min-Hyeon
Proceedings of the Korean Vacuum Society Conference
/
한국진공학회 2014년도 제46회 동계 정기학술대회 초록집
/
pp.271-271
/
2014
본 연구에서는 최근 다양한 전자 소자로써의 연구가 진행되고 있는 그라핀을 SiO2/Si 기판 위에 전자빔 식각(Electron-Beam Lithography)을 이용하여 후면 게이트 전극 구조의 그라핀 채널을 갖는 삼단자 소자를 형성하고 가스 유입이 가능한 진공 Probe Measurement System을 이용하여 금속 전극과 그라핀 간의 접촉저항 (Rc) 및 길이가 다른 채널저항(Rch)를 구하고, 채널 길이, 가스 유량, 온도, 게이트 전압에 따른 I-V 변화를 측정함으로써, 후면 게이트 전극 구조의 그라핀 채널을 갖는 삼단자 소자의 가스 센서로서의 가능성을 연구하였다. 후면 게이트 전극 구조의 그라핀 채널을 갖는 삼단자 소자는 전자빔 식각(Electron-Beam Lithography)에 의해 패턴을 제작하고 Evaporator를 이용하여 전극을 증착 하였다. 소자의 소스 (Source)와 드레인 (Drain)은 TLM (Transfer Length Method)패턴을 이용하여 인접한 두 개의 전극간 범위를 변화시키는 형태로 제작함으로써 소스-드레인간 채널 길이가 다르게 하였다. 이 때 전극의 크기는 가로, 세로 각각 $20{\mu}m$, $40{\mu}m$이며 전극간 간격은 $20/30/40/50/60{\mu}m$로 서로 다르게 배열 하였다. 제작된 그라핀 소자는 진공 Probe Measurement System 내에서 게이트 전압(VG)를 변화시킴으로써 VG 변화에 따른 소자의 특성을 평가하였는데, mTorr 상태의 챔버 내로 O2 가스를 주입하여 그라핀의 Dangling bond 및 Defect site에 결합 된 가스로 인한 전기적 특성의 변화를 측정하고, 이 때 가스의 유량을 50 sccm에서 500 sccm 까지 변화시킴으로써 전기적 특성 변화를 측정하여 센서 소자의 민감도를 평가하였다. 또한, 서로 다르게 배열한 소스-드레인 간의 채널 길이로 인하여 채널과의 접촉 면적에 따른 센서 소자의 민감도 또한 평가할 수 있었다. 그리고 챔버 내 온도를 77 K에서 400 K까지 변화시킴으로써 온도에 따른 소자의 작동 범위를 확인하고 소자의 온도의존성을 평가하였다.
In the present study, measurements of thermal contact resistance (TCR) were conducted for joints of brass and aluminium cylinders of 30 mm in diameter, 45 mm in length, when their interfaces were; ⅰ) under vacuum, ⅱ) charged with a pure silicone grease and ⅲ) charged with a mixture of silicone grease and powder of aluminium (#325). Also the data were compared with analytical calculations using Fouche's model. The data of TCR for joints under vacuum state varied in the range of (2∼100)${\times}$10$\^$-5/(㎡$^{\circ}C$/W) depending on their surface roughness. When the contact surfaces were carefully ground, a reduction of 30∼50% in TCR was obtained. But the surface treatment with silicone grease gave rise to a reduction of about 5∼10 times more than that of vacuum state. The analytical prediction by Fouche's model showed a good agreement within 10~30%, for the case of contact surface charged with silicone grease.
Proceedings of the Korean Society Of Semiconductor Equipment Technology
/
한국반도체및디스플레이장비학회 2007년도 춘계학술대회
/
pp.203-206
/
2007
연속 전자 모델과 결합된 종래의 분자 동역학 방법은 원자 사이의 힘과 원자의 전기용량에 의해 야기되는 탄소 나노튜브의 구부러지는 성질의 특성을 해석하였다. 탄소 원자의 전기 용량은 탄소 원자의 길이에 따라 변하였다. 본 연구는 11.567nm($L_{CNT}$)의 길이와 $0.9{\sim}1.5nm(H)$의 안쪽 깊이를 가진 (5,5) 탄소 나노튜브 브리지로 MD 시뮬레이션을 수행하였다. 탄소 나노튜브는 금 표면에 부딪힌 후 탄소 나노튜브 브리지는 약 ${\sim}1{\AA}$의 크기로 금 표면에서 진동하며, 크기는 차츰 감소하였다. $H{\leq}1.3nm$일 때, 탄소 나노튜브 브리지는 첫 번째 충돌 후에 금 표면과 계속 접촉해 있었고, $H{\leq}1.4nm$일 때, 탄소 나노튜브 브리지는 몇 번의 충돌 후에 금 표면과 안정한 접촉상태가 되었다. $H/L_{CNT}$가 0.13보다 작을 때, 탄소 나노튜브 초소형 전자기기 메모리는 반영구적인 비활성의 메모리 장치가 되는 반면에 $H/L_{CNT}$가 0.14보다 클 때 탄소 나노튜브 초소형 전자기기 메모리는 휘발성이거나 스위치 장치로 동작할 수 있다.
Transactions of the Korean Society of Mechanical Engineers
/
제10권6호
/
pp.870-875
/
1986
In this study, full-rounded tip curve of rack and its mating fillet curve of pinion in Involute-circular arc composite tooth profile are derived. Mechanical characteristics are calculated analytically, i.e., Specific sliding, Nominal bending stress at working root circle and the Contact factor of the arc of contact in circular arc part to the arc of double contact. These characteristics compared with standard involute tooth profile are improved in circular arc part of composite tooth profile. To obtain more efficient composite tooth profile, we studied these characteristics with regard to the changes of unwound angle and radius of circualr arc. And a design method of composite tooth profile is suggested. Composite tooth profile are compared with standard involute tooth profile.
Na, Ho-Kyun;Kim, Tae-Il;Lim, Sang-Hoon;Cho, Ki-Young;Chung, Chong-Pyoung;Han, Soo-Boo;Ku, Young
Journal of Periodontal and Implant Science
/
제35권1호
/
pp.153-161
/
2005
파이브로넥틴은 세포외기질에 존재하는 당단백질로 세포의 부착, 이동, 성장 및 분화에 관여하며, 섬유아세포 성장인자는 세포의 증식 이동 및 분화에 영향을 주는 중요한 성장인자로 알려져 있다. 최근 연구에 의하면, 파이브로넥틴은 조골세포의 타이태늄 임플란트 표면으로 이주와 증식 및 골생성을 촉진하며, 섬유아세포 성장 인자는 파이브로넥틴에 상승작용을 한다고 보고된 바 있다. 이 실험의 목적은 파이브로넥틴 및 섬유아세포 성장인자의 복합 단백질을 이용하여 타이태늄 임플란트의 골 반응을 알아보는 것이다. 체중 2.5 kg 내외의 건강한 18 마리의 웅성가토를 준비하여 무균 사육하였고, 순수 타이태늄을 절삭가공하여 직경 3.5mm, 길이 6mm 의 machined surface를 지니는 screw type 의 임플란트를 준비하였다. 사람의 유전자를 기초로, 유전자 재조합법을 통해, 적절한 primer를 이용하여 얻은 섬유아세포 성장인자를 파이브로넥틴 III 형 분절의 9-10 번 도메인에 결합시켜 얻은 복합 단백질을 준비된 임플란트에 표면처리하여 실험군으로 하였고, 표면처리하지 않은 임플란트를 대조군으로 하여, 가토의 좌우 경골에 각각 2 개씩의 임플란트를 식립하였다. 4주 후, 가토를 희생시켜 각 경골 당 한 개의 임플란트에서 뒤틀림 제거력을 측정하였고 나머지 임플란트 식립 부위 에서는 경골을 포함하는 조직표본을 제작하였다. 조직표본상에서 골접촉이 가장 좋은 3 개의 나사산의 길이를 측정하고, 나사와 접촉하는 골의 길이를 측정하여 골-임플란트 접촉도를 구하고, 같은 부위에서 나사산 사이의 면적과 골이 차지하는 면적을 비교하여 골생성률을 얻었다. 실험군과 대조군의 결과는 Student t-test 를 이용하여 신뢰도 95% 수준에서 통계학적 유의성을 검정하였다. 파이브로넥틴과 섬유아세포 성장인자의 복합 단백질로 표면처리된 임플란트와 표면처리를 하지 않은 임플란트는 뒤틀림 제거력에서는 통계적 유의성이 나타나지 않았으나, 골-임플란트 접촉도와 골생성률에서 복합 단백질로 처리된 임플란트가 통계적으로 유의하게 높은 결과를 보였다. 이상의 연구결과로, 섬유아세포 성장인자와 파이브로넥틴 복합 단백질로 처리한 타이태늄 임플란트가 주변 골 형성을 촉진시켜, 골유합을 증진시킴을 알 수 있었다. 따라서, 복합 단백질이 타이태늄 임플란트의 성공률을 높이기 위한 표면개질 물질로 이용될 가능성을 확인할 수 있었다.
Journal of the Korean Institute of Intelligent Systems
/
제8권3호
/
pp.95-103
/
1998
This paper deals with a problem occuring in recognition of tactile images due to the effects of imposed force at a me urement moment. Tactile image of a contact surface, used for recognition of the surface type, varies depending on the forces imposed so that a false recognition may result in. This paper fuzzifies two parameters of the contour of a tactile image with the membership function formed by considering the imposed force. Two fuzzifed paramenters are fused by the average Minkowski's dist; lnce. The proposed algorithm was implemented on the multisensor system cnmposed of an optical tact le sensor and a 6 axes forceltorque sensor. By the experiments, the proposed algorithm has shown average recognition ratio greater than 869% over all imposed force ranges and object models which is about 14% enhancement comparing to the case where only the contour information is used. The pro- ~oseda lgorithm can be used for end-effectors manipulating a deformable or fragile objects or for recognition of 3D objects by implementing on multi-fingered robot hand.
Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
/
제23권1호
/
pp.69-77
/
2009
Recently, As increasing cleanroom size, Stocker system is trending the large size and long distance for LCD material transfer system. In order to rise a rate of production, the manufacturer are on the decrease of total tact time with Stocker system. And the manufacturer are requested to high speed of next generation Stocker system. Therefore, this paper propose Contactless Power Supply(CPS) system about high speed of next generation Stocker system. This paper proposes CPS system is applied in the long distance and straight section with Stocker system. The test results of input/output characteristic and efficiency of CPS system on operating pattern of Stocker system were analyzed, and proved the applicability on commercial use.
Kim, Hyang-Kon;Gil, Hyoung-Jun;Kim, Dong-Ook;Kim, Dong-Woo;Choi, Hyo-Sang
Proceedings of the KIEE Conference
/
대한전기학회 2011년도 제42회 하계학술대회
/
pp.2138-2139
/
2011
본 논문에서는 44V AC 및 DC전원에서 직렬아크에 의한 전선 접속부에서의 산화물 성장 특성에 대하여 실험, 분석하였다. 실험에 사용된 전선은 동전선과 황동선으로 각각 지름 1.0mm을 사용하였으며, 교류의 경우 3가지 접속조건, 직류의 경우 4가지의 접속 조건으로 하여 전선 접촉면에서 직렬아크가 발생하였을 때 2A, 3A, 4A의 전류에서 산화물의 성장 특성과 접촉면 양단의 전압강하 변화, 산화물의 성장 길이 및 방향, 온도 분포 등에 대하여 분석하였다. 실험, 분석결과, 동전선과 동전선의 접속에서 가장 산화물의 성장이 잘 이루어짐을 볼 수 있었으며, 교류에서는 접촉면을 중심으로 좌우로, 직류에서는 접촉면을 중심으로 +극(양극) 방향으로만 산화물이 성장함을 볼 수 있었다. 본 연구 결과는 AC 및 DC 전원에서의 전기안전을 위한 기술 자료로 활용할 수 있을 것으로 기대된다.
This paper describes a design method for the corner radius of a contacting body using the theoretical approach of contact mechanics. A complete contact, as in the case of a sharp-cornered punch, produces singular contact traction: whereas, in an incomplete contact, the singular contact traction disappears because of the rounded corners, and the contact edges are within the rounded regions. The design method aims to determine the conditions of the contact force as well as the material properties in an incomplete contact. The incomplete contact changes into the complete contact again when the contact edges exceed the rounded regions owing to either an increased contact force or the compliance of the materials. The contact length of a rounded punch is used as a parameter to derive the required conditions. As a result, a design formula is obtained, which provides a minimum allowable radius when the materials, normal contact force, and the length of a flat region of the punch are predetermined. This work consists of two parts: Part I includes a theoretical background, design method, and formula, and Part II describes the actual process with the investigation of design parameters.
최근 반도체 및 FPD 산업에서 Glass의 사이즈, 무게의 증가함에 따라 물류 이송 장비의 전원장치인 비접촉 전원장치의 크기와 용량이 증가하는 추세이며, 또한, 클린룸의 규모가 커짐에 따라 물류 이송 장비 시스템의 길이가 길어지고 Vehicle의 수가 증가하는 추세이다. 본 논문에서는 여러 대의 Vehicle간 독립제어가 가능하고, 물류 이송 장비의 구조가 직선부분과 곡선부분이 혼용되어진 구조에서도 사용 가능한 정전류 비접촉 전원장치의 주요 전력변환 토플로지 별 해로해석, 제어방법을 제시하였고 특히 직 병렬 공진 컨버터의 회로해석, 특성평가를 행하였다. 이 특성평가를 바탕으로 정전류 비접촉 전원장치의 시제품을 제작하여 저항성 부하와 선형 구동 시스템에 적용한 Vehicle 2대를 부하로 사용하여 실험을 행하여 실제 적용, 가능함을 보이고자 한다.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.