• Transactions of the Korean Society of Mechanical Engineers
• /
• v.15 no.6
• /
• pp.2147-2159
• /
• 1991

The effects of principal dimensions of internal mixing twin-fluid atomized and operating conditions on the atomizing characteristics are experimentally investigated. The tests are conducted over the wide range of air/liquid ratio to predict influences of the diameter and length of nozzle, contacting angle between air and liquid in the mixing chamber, and air orifice diameter on the mean drop size(SMD), spray angle, distribution of drop size, and spray dispersion, And also, initial distribution of liquid column by air stream within the mixing chamber are observed through the transparent nozzles. A He-Ne laser particle sizer(MALVERN Model 2604) was used to measure the Sauter.s mean diameter( $D_{321}$) and droplet sizes distribution. In this experiment the air/liquid ratio, mixing length and nozzle diameter have a great influence on SMD, spray angle, droplet sizes distribution and spray dispersion.

• Journal of the Korean Society for Precision Engineering
• /
• v.22 no.3 s.168
• /
• pp.86-92
• /
• 2005

In this paper a forward-backward can extrusion process are analyzed by using rigid-plastic FEM simulation. FEM simulation is conducted to investigate forming characteristics such as deformation modes fur different process parameters. Design parameters such as thickness ratio, punch angle, friction factor and diameter ratio are selected to study the effect of them on the pattern of material flow. The analysis is focused mainly on the influences of the design factors on deformation pattern in terms of forming load, extruded length ratio and volume ratio. It is known for the simulation that the forming load, the length ratio and the volume ratio increase as the thickness ratio (TR), the wall thickness in forward direction to that in backward direction, decreases. The various punch angles have slight influence on the forming load. length ratio and volume ratio. However friction factor have little effect on the forming characteristics such as the forming load, volume ratio and so on. In addition the forming load increases as diameter ratio (DR), the outer diameter of a can in forward direction to that in backward direction, increases. Furthermore the extruded length ratio is lowest with a certain value of DR=0.85 among diameter ratios. Pressure distribution exerted on the die-material interface is illustrated schematically.

• Elastomers and Composites
• /
• v.46 no.2
• /
• pp.125-131
• /
• 2011

The effects of chopped kenaf fiber concentration on mechanical property of polypropylene (PP) composite are investigated. The addition of kenaf increased the tensile strength, flexural modulus, impact strength, specific gravity, and HDT, while decreased the elongation%, flexural strength, and melt flow index. The increase of mechanical properties is due to increased surface area contacting between fiber and polymer matrix and fiber-fiber interaction. Volatile extractives in the kenaf seemed to decrease the interfacial adhesion between kenaf surface and PP.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2015.05a
• /
• pp.553-556
• /
• 2015

In almost all of the Hand-made suit plants, while garment cutters are hard to measure the body size by their own, they are not quick. And each of the individual's standard is vague, so it is hard to get a consistency. So it will give the customers some displeasure with the body contact. To improve this kind of problems, in this paper proposes a efficient way that is hard to measure by the general image processing technology to measure when you manufacture a Hand-made suit and measure a body size by wearing a elastic band that has a printed mark that has some information of length and taking a picture of the body by a digital camera.

• Journal of Korea Multimedia Society
• /
• v.8 no.5
• /
• pp.651-659
• /
• 2005

For segmentation of constrained and handwritten Hangul, a new method, which has been not introduced, was proposed and implemented to use virtual network search system in the space between characters. The proposed system was designed to be used in all cases in unconstrained handwritten Hangul by various writers and to make a number of curved segmentation path using a virtual network to the space between characters. The proposed system prevented Process from generating a path in a wrong position by changing search window upon target block within a search process. From the experimental results, the proposed virtual network search system showed segmentation accuracy of $91.4\%$ from 800 word set including touched and overlapped characters collected from various writers.

• Tribology and Lubricants
• /
• v.31 no.4
• /
• pp.177-182
• /
• 2015

Tapered roller bearings are widely used in equipment where high combined thrust and radial loads are experienced. A certain amount of tilting between the tapered rollers and the races always occurs because of bending moment load conditions and shaft deflection. It is now well understood that a coherent elastohydrodynamic lubrication (EHL) film separates the rollers and races. In spite of extensive study on EHL problems for over half a century, relatively few studies have focused on the finite line contacts problem. This study presents a complete numerical analysis of the effects of roller tilting on the EHL characteristics in a tapered roller bearing. We systematically analyze this highly nonlinear problem using finite differences with fully non-uniform grids and the Newton-Raphson method. Detailed EHL pressure distributions and film shapes are presented under moderate loads and material parameters. A very small roller tilting significantly affects the pressure distributions and film shapes near both ends of the roller. Moreover, the effect of tilting on the EHL characteristics at the small end is much greater than that at the large end. Therefore, in designing optimum profiles for tapered roller bearings, the profile radius should be larger at the small end.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.126-126
• /
• 2011

삼차원 구조의 낸드 플래시 메모리 소자는 기존 이차원 구조의 메모리 소자를 비례 축소할 때 발생하는 단채널 효과와 간섭효과를 최소화 하면서 집적도를 높일 수 있는 장점 때문에 많은 연구가 진행되고 있다. 그러나, 삼차원 구조의 낸드 플래시 메모리 소자는 공정 과정이 복잡하고 주변 회로 연결이 어려울 뿐만 아니라 금속 접촉에 필요한 면적이 넓은 단점을 가지고 있다. 이러한 문제점을 해결하기 위해 Vertical-Stacked-Array-Transistor (VSAT) 구조를 갖는 플래시 메모리 소자가 제안되었으나, VSAT 구조 역시 드레인 전류량이 적고 program과 erase 동작 시게이트 양쪽의 전하 트랩층에 전자와 정공을 비효율적으로 포획해야 하는 문제점을 가진다. 본 연구에서는 기존의 VSAT 구조의 문제점을 개선하면서 집적도를 증가한 삼차원 구조의 고집적낸드 플래시 메모리 소자를 제안하였다. 본 연구에서 제안한 플래시 메모리 소자의 구조는 기존 VSAT 구조에서 수직 방향의 두 string 사이에 존재하는 polysilicon을 제거하고 두 string 사이에 절연막을 증착하였다. 삼차원 시뮬레이션 툴인 Sentaurus를 사용하여 이 소자의 동작특성을 시뮬레이션 하였다. 소스와 드레인 사이의 유효 채널 길이가 감소하였기 때문에 기존의 VSAT 구조를 갖는 메모리 소자에 비해 turn-on 상태의 드레인 전류가 증가하였다. 제안한 플래시 메모리 소자의 subthreshold swing (SS)가 기존의 VSAT 구조를 갖는 메모리 소자의 SS 에 비해 낮아, 소자의 스위칭 특성이 향상하였다. 프로그램 전후의 문턱전압의 변화량이 기존의 VSAT 구조를 갖는 메모리 소자에 비해 크기 때문에 멀티 레벨 동작이 가능하다는 것을 확인하였다.

• Journal of Korea Foundry Society
• /
• v.27 no.5
• /
• pp.224-227
• /
• 2007

원자로에 장전되는 $^{99}Mo$ 조사표적을 제조하기 위한 우라늄박판은, 박판 품질, 생산성, 경제성 문제로 인해, 기존의 열간압연방법에 의해 실험실 규모로는 제조가 가능하나, 상용 규모로는 제조되기 어려운 실정이므로, 새로운 제조방법의 개발이 요구되고 있다. 이와 같은 상황에서, $^{99m}Tc$의 모핵종인 방사선 동위원소$^{99}Mo$ 생산하기 위하여 planar flow casting (PFC) 법에 의해 다결정질 우라늄박판에 대한 새로운 제조방법이 연구되었다. $100{\sim}150\;{\mu}m$의 두께 및 너비 약 50mm의 연속적인 다결정질 우라늄박판이 하나의 batch에서 5m 이상의 길이로 제조되었다. 우라늄박판은 불순물이 거의 없었으며 양호한 표면조도를 가지고 있었다. 우라늄박판의 냉각를 접촉표면은 자유표면 보다 매끈한 자유표면을 가지고 있었다. 우라늄박판은 제조공정변수와는 상관없이 ${\alpha}-U$ 상을 가진 약 10 ${\mu}m$ 이하의 미세한 다결정립을 가지고 있었다.

• Korean Chemical Engineering Research
• /
• v.49 no.6
• /
• pp.835-839
• /
• 2011

The characteristics of torch-type atmospheric pressure plasma and its sterilization effects have been analyzed. The length of plasma flame was varied with the level of applied voltage and the mixture gases composed of argon and oxygen. The effect of plasma flame on the temperature increase of surface treated was limited to $43^{\circ}C$ as a maximum temperature under exposing time of 10 min. The sterilization for E. coli was strongly affected by the applied voltage, the oxygen ratio in the mixture gas and the treatment time. At a high concentration of ozone, the increase of treatment time under the direct contact with plasma flame yields to maximize the effect of the sterilization on E. coli.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.6
• /
• pp.1390-1398
• /
• 1988

The purpose of this study was experimentally to investigate the disintegration process and disintegration mechanism when co-axial air flows vertically for the longest smooth liquid jet. These were affected by liquid velocity, air velocity, air-to-liquid diameter ratio, nozzle shape, and air-liquid contacting position. That is, this process of disintegration of the liquid jet was similar to that occurred when liquid pressure was increased. At Reynolds number of 10, 000 and below, the changes in the breakup length represent different tendency according to liquid flow rate. The influence of air flow on the disintegration of liquid jet was different according to air-to-liquid diameter ratio, air orifice diameter, nozzle shape and contacting position of liquid and air. In particular, when the tip of liquid nozzle was inside the air orifice, the effect of air flow was the larger than outside the air orifice. The effect of liquid mass flow rate on the change rate of the breakup length was also different.