• Composites Research
• /
• v.20 no.3
• /
• pp.8-16
• /
• 2007

Bending collapse of light-weight square tubes used for vehicle structure components is a dominant failure mode in oblique collision and rollover of vehicles. In this paper bending performances of aluminum-GFRP hybrid tube beams were evaluated in relation with bending deformation behavior and energy absorption characteristics. Aluminum/GFRP hybrid tube beams fabricated by inserting adhesive film between prepreg and metal layer were used in the bending test. Failure mechanisms of hybrid tubes under a bending load were experimentally investigated to analyze the bending performance as a function of ply orientation and composite layer thickness. Ultimate bending moments and energy absorption capacity of hybrid tube beams were obtained from the measured load-displacement corves. It was found that aluminum/GFRP hybrid tubes could be converted to rather stable collapse mode showing excellent energy absorption capacity in comparison to the pure aluminum tube beams. In particular, the hybrid tube beam with $[0^{\circ}/90^{\circ}]s$ composite layer showed a large improvement by about 78% in energy absorption capacity and by 29% in specific energy absorption.

• Horticultural Science & Technology
• /
• v.32 no.2
• /
• pp.184-192
• /
• 2014

Various types of unit packaging methods were applied for 'Fuji' apples during short-term cold storage and export simulation. Gas tightness of the package was controlled stepwise in the successive two-year experiments using different perforation treatments (none, punch hole, or pinhole) and sealing methods (tie v s. heat seal). Risk of tight packaging and effectiveness of macroperforation on weight loss and quality maintenance were analyzed as related to changes in gas concentration inside the packages. Immediately after harvest, each 5 apple units were packaged in $40{\mu}m$ polypropylene (PP) film bags, stored 4 weeks at $0^{\circ}C$, and then put on the shelf for one week at ambient temperature in the preliminary experiment, In the main experiment, export process was imposed after storage simulating 2 week refrigerated container shipment at $0^{\circ}C$ plus one week local marketing at ambient temperature. Non-perforated film packaging with relatively high gas tightness induced flesh browning caused by carbon dioxide accumulation regardless of the sealing methods. Among perforated film packaging, in contrast, atmospheric modification was partly established only in the pinhole treatment and flesh browning symptom was not observed in all the treatments. Even the punch hole perforated film packaging without gas tightness effectively reduced the weight loss, whereas had slight benefits for quality maintenance. Reduced perforation using pinhole treatment seemed to improve sensory texture, while effects on physicochemical quality were insignificant. Overall results suggest the need of more minute perforation treatments on the packaging film to ensure modified atmosphere effects on quality maintenance.

• Composites Research
• /
• v.29 no.5
• /
• pp.249-255
• /
• 2016

The fiber metal laminates have been widely used at aerospace industry due to outstanding fatigue characteristic, corrosion resistance and impact resistance and so forth. The objective of this research is to establish the proper manufacturing variables for enhancing the interfacial energy release rate of fiber metal laminates using Taguchi method. The major variables of the manufacturing process are surface treatment, pre-specified temperature holding time and additional pressure. In order to determine the interfacial adhesive strength, the double cantilever beam and end-notched flexure tests were conducted. Afterward, Mode I and II energy release rates at various conditions were introduced signal-to-noise ratio with respect to each condition. Finally, the most efficient manufacturing variables are recognized using larger-the-better characteristic.

• Journal of Adhesion and Interface
• /
• v.11 no.3
• /
• pp.112-119
• /
• 2010

Poly(methyl methacrylate)/poly(butyl acrylate) PMMA/PBA core-shell composite particles were prepared by the emulsion polymerization of MMA and BA in the presence of different concentration of sodium dodecyl benzene sulfonate (SDBS). The following conclusions are drawn from the measured conversion and particle size distribution, morphology, average molecular weight distribution, observation of film formation and particle formation, glass transition temperature and physical properties of polymerized core-shell composition particles for using adhesive binder. When the concentration of 0.03 wt% surfactant, the conversions of PMMA and PBA core polymerization are excellent as 95.8% for PMMA core and 92.3% for PBA core. Core-shell composite particles are obtained 90.0% for PMMA/PBA core-shell composite particles and 89.0% for PMMA/PBA core-shell composite particles. It is considered that the core and shell particles are polymerized to be confirmed FT-IR spectra and average molecular weight measured with a GPC, formation of the composite particles is confirmed by the film formation from normal temperature, and composition of inside and outside of the composite particle is confirmed by TEM photograph. The synthesized polymer has two glass transition temperatures, suggesting that the polymer is composed of core polymer and shell polymer unlike general copolymers. It is considered that each core-shell composite particle can be used as a high functionality adhesion binder by the measurement of tensile strength and elongation.

• Composites Research
• /
• v.19 no.4
• /
• pp.23-30
• /
• 2006

In the development of a cryogenic propellant tank, the proper selection of adhesives to bond composite and metal liner is important for the safety of operation. In this study, 3 types of adhesives were tested for the ability to bond CFRP composites developed for cryogenic use and aluminum alloy (Al 6061-T6) for lining the tank using double-lap joint specimens. The double-lap joint specimens were tested inside an environmental chamber at room temperature and cryogenic temperature ($-150^{\circ}C$) respectively to compare the bond strength of each adhesive and fracture characteristics. The material properties with temperature of component materials of double-lap joints were measured. In addition, ABAQUS was used for the purpose of analyzing the experimental results.

• Polymer(Korea)
• /
• v.37 no.3
• /
• pp.373-378
• /
• 2013

The interfacial adhesion strength is very important in $SiO_x$ deposited PC film for the barrier enhanced polycarbonate (PC) flexible substrate. In this study, PC films were treated by undercoating, UV/$O_3$ and low temperature plasma and then the effect of physical and chemical surface modifications on the interfacial adhesion strength between PC film and $SiO_x$ barrier layer were studied. It was found that untreated PC film shows significantly low interfacial adhesion strength due to the smooth surface and low surface free energy of PC. Low temperature plasma treatments resulted in the increase of both surface roughness and surface free energy due to etching and the appearance of polar molecules on the PC surface. However, UV/$O_3$ treatment only shows the increase of surface free energy by developed polar molecules on the surface. These surface modifications caused the enhancement of surface interfacial strength between PC film and $SiO_x$ barrier. In the case of undercoating, it was found that the increase of surface interfacial strength was achieved by adhesion between various acrylic acid on acrylate coated surface and $SiO_x$ without increase of polar surface energy. In addition, the barrier property is also improved by organic-inorganic hybrid multilayer structure.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.6
• /
• pp.272-277
• /
• 2019

In this paper, a manufacturing method of an anti-glare cover glass on LCD for outdoor use is proposed. The main specification of cover glass is hardness and anti-glare. Hardness is achieved by using the tempered glass, and anti-glare(AG) film is laminated to meet anti-glare specification no the tempered glass. However, the AG film is difficult to maintain the AG performance continuously because the abrasion resistance of the PET film itself is as weak as about 3H. Therefore, a novel production procedure using screen printing method is proposed. The proposed coating is implemented by applying $ZnO-B_2O_3-SiO_2$ powder on glass surface and the glass is made with enhanced hardness through tempering process. In order to apply the ZBS powder uniformly on the glass surface, a screen printing process is used. The main parameters to be considered in screen printing are the oil concentration and mesh opening size. Because the amount of ZBS powder applied to the printing process is controlled by these two parameters, the correlativity is confirmed through the experiments. In order to evaluate the performance of the proposed method, the haze, surface roughness and transmittance are selected as the performance index and are compared with the AG film. As a result of comparison, it is verified that the transmittance of the proposed tempered glass is 83.1%, which is slightly lower than 89.5% of AG film, but the hardness is more than double to 7H.

• Polymer(Korea)
• /
• v.34 no.6
• /
• pp.560-564
• /
• 2010

Dimensional stability of LCD polarization film consisted of triacetyl cellulose (TAC) and poly(vinyl alcohol) (PVA) film has been studied and especially, the effect of PVA adhesive on the dimensional stability has been considered as function of deacetylation and molecular weight of PVA adhesive. The maximum adhesion strength between TAC and PVA film was obtained in the laminate using PVA adhesive with 70% of OH content and the effect of molecular weight on the adhesion strength was only pronounced in the laminate using PVA adhesive with OH content above 70%. It was found that the optimum dimensional stability of TAC/PVA/TAC laminate (polarizing film) was obtained when applied PVA adhesive has low molecular weight and it was more dependent upon the OH content than the adhesion strength between TAC and PVA films.

• Journal of the Korean Ceramic Society
• /
• v.39 no.5
• /
• pp.467-472
• /
• 2002

Long Carbon Nanotubes(CNTs) were cut by diamond lapping film followed by observation using SEM. The paste was prepared by mixing shortened CNT powder, ${\alpha}$-terpineol used as a solvent, and ethylcellulose as a binder. This paste was deposited on glass substrate by screen printing and extruded by syringe. After screen printing, several post-treatments were performed to control the alignment of CNTs perpendicular to the substrate. The deposited CNTs were scratched by sand paper or diamond lapping film. It was also treated by attachment followed by an immediate detachment using the adhesive tape. SEM observation indicates that excellent vertical alignment of CNTs could be achieved by simple post-treatments from the screen printed-CNTs paste. Similar alignment of CNTs is also observed in the as-extruded CNTs paste.

• Polymer(Korea)
• /
• v.30 no.1
• /
• pp.70-74
• /
• 2006

Plasticized cellulose diacetate(CDA) was prepared by homogenizing cellulose diacetate(CDA), triacetin(TA) and epoxidized soybean oil (ESO) in a high-speed mixer, then the CDA mixture was mixed with ramie fiber to produce a green composite material. In DMA analysis, the glass transition temperature of plasticized CDA and the composite was observed at $85\;^{\circ}C\;and\;140\;^{\circ}C$, respectively. A composite reinforced with alkali treated ramie fiber exhibited significantly higher mechanical properties, such as $15\;^{\circ}C$ increase in tensile strength as well as $41\;^{\circ}C$ increase in Young's modulus when compared with commercial polypropylene. In the SEM image analysis, much enhanced adhesion between plasticized CDA and alkali treated ramie fiber (AIRa) was observed.