• Journal of the Korean Wood Science and Technology
• /
• v.32 no.2
• /
• pp.65-72
• /
• 2004

A melamine-urea-formaldehyde (MUF) resin, based on 5 percent melamine addition of the resin solids weight, was synthesized in the laboratory for particleboard (PB) manufacture. Laboratory PBs were made with the MUF resin at three press times (3, 4, 5 min) and two resin application rates (6, 8 percent). Enclosed caul system was used for collecting the exhaust gases materials generated during the hot-pressing of PBs. Exhaust gases materials generated inside the enclosed caul during the hot-pressing of PBs were collected in a controlled air stream. Formaldehyde from the exhaust gases collected was determined per a chromotropic method of the National Institute of Occupational Safety and Health Method 3500. The measurement results showed that formaldehyde emissions during the hot-pressing of PB significantly increased with increasing press time, and MUF resin application rates. PB' performance test results showed that internal bond (IB) of PB made with 3-minute press time exceeded the minimum requirement for KS F 3104 PB type 8.0.

• Magazine of the Korea Concrete Institute
• /
• v.14 no.2
• /
• pp.45-50
• /
• 2002

근년, 철근 콘크리트조 구조부재의 열화 및 건축물의 용도변경에 따라 건축물의 보수 및 보강에 관한 공법의 개발 및 그 효과를 검증하려는 연구가 활발히 진행되고 있다. 이에 따라, 보강공법으로서는 경제성ㆍ시공성 면에서 우수한 탄소섬유시트, 아라미드섬유 시트, 유리섬유시트 보강공법 및 FRP판 보강공법 등 합성수지 접착제를 사용하는 새로운 보강공법들이 폭넓게 연구되어 현장 실용화되어 사용 중에 있다. 그러나, 이들 보강공법에 관한 연구는 주로 구조적인 내력 보강효과 산정에 관한 것이 대부분이고 보강후의 내화성능 및 내구성능에 관한 연구는 매우 부족한 실정이다. 이들 보강공법은 주로 에폭시수지계 접착제에 의하여 콘크리트와 보강재의 접착력에 의하여 내력이 전달되는 메커니즘으로 되어있어 화재가 발생한 경우 내화피복이 없다면 접착제 자체의 연소에 의하여 유독가스의 발생 및 접착강도가 크게 저하되어 그 구조적인 보강성능은 급속히 저하할 것으로 판단된다. 또한, 현재 이들 보강공사는 내화성능의 검토 없이 실제 시공이 이루어지고 있으므로 화재시에는 대형참사를 일으킬 위험성이 있다.(중략)

• Journal of the Korea Institute of Building Construction
• /
• v.24 no.3
• /
• pp.331-341
• /
• 2024

In this study, the flexural strength and ductility of steel-timber composite beams were evaluated to enhance the structural performance of glued-laminated timber beams. Three specimens were fabricated, including one reference glulam beam and two composite beams. The composite beams were constructed by attaching steel sections to the glulam beam using either liquid adhesive or screws. The experimental results showed that the structural performance of the steel-timber composite beams was approximately 2-3 times higher than the reference glulam beam, indicating that both flexural strength and ductility were sufficiently ensured. Notably, the specimen constructed with liquid adhesive demonstrated superior structural performance compared to the screw-attached specimen.

• Applied Chemistry for Engineering
• /
• v.28 no.4
• /
• pp.454-459
• /
• 2017

In this study, aqueous acrylic emulsion adhesives were prepared using various surfactants and their properties were also investigated. Solids content, conversion, particle size distribution and initial adhesion properties of the prepared adhesives were compared with each other. The solid content of the adhesives was evaluated 60% and the conversion rate of the emulsion polymerization was 97% at 2 wt% concentration of synthesized surfactants. The particle size distribution analysis revealed that the size distribution of adhesive particles was 290~470 nm when the synthesized cationic surfactant was added. The initial adhesion and adhesion time were also improved. The maximum adhesive strength was found to be 2.55 kgf when using a single surfactant (POE 23), and superior to that of using other surfactants. It was confirmed that the corrosion inhibition of the adhesive prepared by adding the cationic gemini surfactant was maintained for 48 hours.

• Polymer(Korea)
• /
• v.31 no.5
• /
• pp.369-373
• /
• 2007

In this study, solvent-free pressure sensitive adhesives (PSA) using acrylic copolymer was prepared by UV radiation to investigate the effect of comonomer on the adhesion properties. Adhesive force value of PSA was increased with the amount of comonomer having shorter side chain due to the enhanced intrinsic surface energy. Peel and shear strength were also influenced by chemical properties of comonomer. The addition of comonomer, ethyl and n-butyl acrylate allows PSA sample with high peel and shear strength. This nay be explained in terms of correlation between loss modulus and glass transition temperature of PSA. As the addition of acrylic comonomers with long side chain length decreases the loss modulus of PSA, the deformation of PSA can not be inhibited.

• Restorative Dentistry and Endodontics
• /
• v.32 no.5
• /
• pp.445-458
• /
• 2007

The purpose of this study was to evaluate the bond strength of a new Single step system with different curing mode composites, and to evaluate the effect of the intermediate resins which have different hydrophilicity on bonding ability by means of the micro shear bond testing and TEM examination for the adhesive interface. The adhesive used in this study was an experimental single step system (Bisco Inc., Schaumburg IL). Experimental groups were produced by using six kinds of intermediate resin having different hydrophilicity that was hydrophilic, hydrophobic and most hydrophobic resin and as filled or not after applying adhesive. Each experimental group was further divided into two subgroups whether the adhesive was light cured or not. Dual cured composite (Bis Core, Bisco Ltd., Schaumburg, IL) was placed on the adhesive layer as light cure or self cure mode. The results or bond strength were statistically analyzed using one way ANOVA and multiple comparisons are made using Tukey's test at ${\alpha}\;<\;0.05$ level. The results of this study were as follows ; 1. The application of intermediate resin did not increase the bond strength for light cured composite. 2. The bond strength of an experimental adhesive with self cured composite was significantly increased by the application of intermediate resin layer. 3. The bond strength of adhesive was irrespective of the cure or not of itself before intermediate resin layer applied. 4. As applied hydrophilic resin layer was, the initial bond strength was higher than both hydrophobic and most hydrophobic one used but there was no significance. Using a single step adhesive with dual/self cured composite, the incompatibility between both of them should be solved by the application of intermediate hydrophobic resin to reduce the adhesive permeability. However, Single step adhesive can be used in the light cured composite restoration without any decrease of the initial bond strength.

• Korean Journal of Heritage: History & Science
• /
• v.49 no.4
• /
• pp.114-125
• /
• 2016

Lacquer is one of the most widely used natural resin in East Asia since Neolithic Age. As a major ingredient of lacquerware, lacquer is waterproof, insect-proof and rot-proof to be durable and anti-abrasion, generally utilized for mainly painting purpose. According to lacquerware excavated from several sites of Japan and China, lacquerware seems to appear in Neolithic Age. On the other hand in case of excavation research in Korea, lacquerwares are found after the Bronze Age. The initial purpose of lacquer is estimated to be adhesive, regarding the literatures mentioning bitumen(Yeoksceong ), animal glue(Kyeo) and egg alumen(Nanbaek). Especially piece of jar coffin unearthed in Pyeongtaek Daechu-ri site had trace of restoration by lacquer and hemp as an evidence of lacquer for adhesion in Pre-Three Kingdoms period. Since then a trend to restore the broken ceramics with lacquer and decorate with golden foil lasted especially in Joseon Dynasty. In the field of gold plated lacquer method, mother-of-pearl inlaying technique for lacquerware and restoration of buildings, lacquer is still used as adhesive. Due to matter of reversibility lacquer is being avoided for conservation and restoration of cultural heritage. Lacquer as a traditional material for adhesive since ancient times, however, has advantage in adhesion strength and durability. Because synthetic resin adhesive has problem of emission of volatile organic compounds and aging over time, lacquer receives attention recently. On the contrary, by combination adhesive from mixing lacquer and animal glue, already proved the possibility of applicability and chemical modification. A research to utilize lacquer as modern paint or functional material is also conducted continuously also in China and Japan. To put traditional material into practical use and modernize, chemical research from the molecular level of the lacquer is necessary in the near future.

• Journal of Adhesion and Interface
• /
• v.23 no.4
• /
• pp.137-143
• /
• 2022

In this study, the polyurethane acrylates (PUA) resin with good adhesive and flexibility for adhesive for shoes and clothing were synthesized using that poly(tetramethylene adiphate glycol) (PTAd), poly(tetramethylene ether glycol) (PTMG) as polyester polyol and polyether polyol respectively, including 4,4'-methylene diphenyl diisocyanate (MDI), isophorone diisocyanate (IPDI), 1,4-butandiol (1,4-BD), 2-hydroxyethyl methacrylate (2-HEMA) and dibutyl amine (DBA). The effect of polyol blend in the polyurethane acrylate on thermal and mechanical properties, adhesion strength and flexural strength were studied. The glass transition temperature (T_g) of PUA was confirmed in range of -70~-40 ℃. In addition, the glass transition temperature (T_g), decomposition temperature (T_d), tensile strength adhesion strength and heat resistance were increased as increasing of PTAd amount while the elongation, water resistance and flexural properties were decreased. The synthesized polyurethane acrylate with 5:5 ratio of PTAd and PTMG indicated the highest adhesion strength and flexural properties.

• Journal of Conservation Science
• /
• v.36 no.6
• /
• pp.475-482
• /
• 2020

In this study, we synthesized rosin-based epoxy resin and manufactured two components adhesives and epoxy putty using this epoxy resin. This study manufactured main element of adhesives for enabling it to form epoxide group by letting epichlorohydrin react to maleic anhydride modified rosin, and used room temperature curing type triethylenetetramine for hardener. The ratio between main element and hardener of of manufactured adhesives was 100 : 20, and main element and hardener of filling material were manufactured as clay type by mixing them with filler. Manufactured undiluted adhesives and filling material showed very stable result in the adhesive strength (3.06 MPa) and ultraviolet irradiation, showing outstanding result comparing to existing restoration adhesives. And it is considered a material having reversibility as it was dissolved in organic solvents such as acetone and toluene after being hardened, which showed a result that solved part of possible problems caused by restoration. As a result of use and application of manufactured adhesives and filling material for actual wood crafts, they showed excellent results in workability, stability, removability etc., and this study confirmed that the material can be used for and applied to various fields.

• Proceedings of the Korean Fiber Society Conference
• /
• 1998.04a
• /
• pp.50-53
• /
• 1998

코팅이나 접착제 분야에서 대기 중에서 불안정한 이소시아네이트기를 보호하기 위해 phenol, oxime, caprolactam계 화합물을 사용하는 봉지 방법을 본 연구에서 이용하고자 하였다. 선천적으로 위의 화합물들로 봉지된 이소시아네이트기는 결합쇄로 carbamate를 형성하나 이들은 열에 의해 특정 온도 영역에서 해리 되면서 다시 이소시아네이트기가 재 생성되는 과정을 거친다.(중략)