• Proceedings of the KIEE Conference
• /
• 1993.07a
• /
• pp.24-26
• /
• 1993

The dielectric properties of pressboard depend on the chemical and fine structures as well as on the macroscopic structure of pressboard. The investigate on the dielectric characteristics of pressboard therefore, provides an important approach to an understanding of the correlation between the characteristics and the structure of pressboard. The purpose of this research is to investigate the dielectric properties of pressboard.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.1983-1985
• /
• 2005

This paper describes moisture content, dielectric strength and dielectric properties of thermally accelerating aged insulating paper as varnish treatment. Kraft, nomex paper were impregnated with diluted varnish, varnish and solvent were diluted in the ratio of 40wt%, in vacuum condition, and then completely dried. To analysis of papers were influenced by varnish treatment, we applied thermal stress, and then measured moisture content, dielectric strength and relative permittivity, $tan{\delta}$ as varnish impregnated papers.

• Proceedings of the KIEE Conference
• /
• 1993.07b
• /
• pp.558-560
• /
• 1993

The dielectric properties of pressboard depend on the chemical and fine structures as well as on the macroscopic structure of pressboard. The investigate on the dielectric characteristics of pressboard, therefore, provides an important approach to an understanding of the correlation between the characteristics and the structure of pressboard. The purpose of this research is to investigate the dielectric properties of pressboard.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.449-452
• /
• 2004

The life of power transformer is basically dependent on the aging deterioration of insulating paper. Analysis of insulating paper for its DP value or tensile strength requires removal of a few strips of paper but direct measurement of this properties is not practical for in-service transformers. For this reason furfural analysis by HPLC has gained increasing favor as a means of estimating degradation of insulating papers in power transformers and this paper reports on the analysis of data on the concentration of furfural in oil samples from about 50 power transformers and the case study. The data showed that furfural content can estimate more accurately aging characteristics compared to concentration of CO, $CO_2$. We expect that these results can be useful to predict the aging characteristics and life diagnosis of power transformers and further the study must be continued.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2004.07a
• /
• pp.465-468
• /
• 2004

In this paper, the properties of temperature dependence and voltage dependence of Aramid paper were studied to understand electrical characteristics, to be regarded as the excellent insulation. Aramid paper and pressboard had being applied various motor, generator. We used to Finite Elemental Method of simulation tool, and improved optimal insulating design of insulating Aramid according to calculated those.

• Progress in Superconductivity and Cryogenics
• /
• v.12 no.1
• /
• pp.52-55
• /
• 2010

A sub-cooled liquid nitrogen system is known as a promising method to develop high voltage superconducting apparatuses such as superconducting fault current limiters (SFCLs) and superconducting cables. To develop a high voltage superconducting machine adopting the sub-cooled liquid nitrogen system with a constant pressure. injecting a non-condensable gas is indispensable. In this study. the dielectric characteristics of insulation gases are investigated and analyzed by using electric utilization factors ($\xi$). It is found that the maximum electric field at sparkover that occurs with 50 % probability. $E_{MAX.50%}$ exponentially decreases as the S increases. This means that the $E_{MAX.50%}$ at sparkover can be estimated with the $E_{MAX.50%}$

• The Transactions of the Korean Institute of Electrical Engineers C
• /
• v.53 no.10
• /
• pp.523-529
• /
• 2004

Faults of cellulosic insulations greatly affect the life span of oil immersed transformers because their performance recovery is impossible. Therefore, the reliable diagnosis technologies are needed for detection of the faults. Dissolved gas analysis technologies using CO and $CO_2$ gases have been widely used for fault diagnosis of cellulosic insulations. In this research, we described Degradation diagnosis of insulation paper CO and $CO_2$ gases in oil immersed Transformers using. We considered the distribution characteristics of CO, $CO_2$ gases' concentrations and ratios of $CO_2$/CO not only in serviced transformers but in experiments with typical fault causes such as heat, partial discharge and moisture. As result, the reliability of diagnosis results for the cellulosic insulations can be improved when the concentrations of CO, $CO_2$ and the ratio of CO/$CO_2$ satisfy each diagnosis criterion at a tim

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.65 no.9
• /
• pp.1518-1523
• /
• 2016

In this study, in order to understand the degradation characteristics of oil-paper insulation for power transformers and OF cables, tan delta was measured using cable model specimens with long-term accelerated thermal and electrical aging. In addition, to find out the degradation level due to the accelerated aging, tensile strengths of aged papers were measured. As a result, tan ${\delta}$ showed the characteristics of slight decrease at the first stage and then increase with the aging time, which could be analyzed due to the evaporation of remaining moisture and the change of aging rate with time. Also, the trend of tensile strengths with aging temperature and time was appeared to be exponentially decreased and by use of these data equivalent calculated lifetimes and accelerated aging factors were derived for each aging temperatures. After then, tan ${\delta}$ was analyzed with the equivalent operating years. For all different aging temperatures, the aged data were very well fit to the equivalent operating years and it is shown that tan ${\delta}$ was increased with the decrease of tensile strength.

• Journal of the Korea Convergence Society
• /
• v.11 no.1
• /
• pp.175-180
• /
• 2020

In this study, we developed a micropattern technology in the shape of RFID TAG antenna using ultrasonic micropattern manufacturing system developed to enable micropattern technology. The ultrasonic tool horn in longitudinal vibration mode was installed in the micropattern manufacturing system to develop the ultrasonic press technology for the micropattern antenna shape of the RFID TAG antenna shape on the insulating sheet surface. The ultrasonic shaping technology was manufactured by applying the resonance design technique to a 60kHz tool horn, and by using the micropattern manufacturing system, the coil wire having a thickness of 25㎛ can be ultrasonically press-molded on an insulating sheet of 200㎛ or less. In ultrasonic press technology, the antenna shape having a minimum line width of 150㎛ could be molded without disconnection, peeling, or twisting of the coil wire.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.8 no.2
• /
• pp.413-419
• /
• 2004

This paper describes a technique that can predict electric fires by detection of discharge voltage signals caused by the use of electric facilities. In the experiment, various discharge modes, a flashover or a surface discharge through insulation paper and a line to line short, were simulated to acquire electrical information for predicting electrical fire as discharge modes. From the experimental results, it is hewn that electorial discharges which are ranked as majority causes of electric fires generate characterized signals distinguished from power frequency. Finally. We designed a prototype discharge detector based on the experimental results, and the detector is applied to a power lines. This study showed that the prediction of electric fires is possible by monitoring discharge voltage signals in electric power lines.