• Journal of Korea Foundry Society
• /
• v.27 no.5
• /
• pp.217-220
• /
• 2007

절삭특성은 재료를 원하는 형상으로 가공하기 위해 재료의 불필요한 부분을 제거할 경우 그 가공성이 쉽거나 어려움에 대한 정도로 전의될 수 있는데 동합금 소재의 절삭특성은 절삭시 발생된 칩의 형상이나 길이를 측정하거나 또는 공구계에 부착된 토오크 미터에 의해 절삭력을 간접적으로 측정하는 방법 등이 사용되어 오고 있다. 상기의 평가방 법은 절삭특성의 간접적인 평가방법이라는 한계와 정확도에 문제가 있는 실정이다. 본 연구에서는 압전형 공구동력계(Piezoelectric Tool Dynamometer)를 쾌삭인청동합금 피절삭물에 직접 부착하여 절삭가공시 절삭력은 정량적으로 직접 측정하고자 하였다. 쾌삭인청동합금의 소둔 열처리 시간이 증가할수록 결정립의 성장에 의한 연화현상과 납입자의 군집화(Clustering)는 관찰되었으나 그로 인한 절삭력 및 절삭에 필요한 에너지의 변화는 뚜렷하지 않았다.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.4
• /
• pp.78-87
• /
• 1997

In machine tools, frictional force exists between the table and the guideways, and in ballscrews. In this paper, feed motor current measured by a hall sensor is used to calculate the motor torque. Some frictional phenomena are studied in feed drive systems, such as the relationship between feedrate and frictional torque, and chip cover effects on frictional torque. Considering frictional phenomena, the relation- ship between the feed froce and the feed motor current id obtained. Feed force can be well estimated by feed motor current measurement considering frictional behavior. The relationship between the cutting force and the feed motor current is slightly different between up milling and down milling due to the effect of y direc- tional cutting force on frictional torque.

• Journal of the Korean Society for Precision Engineering
• /
• v.13 no.2
• /
• pp.133-145
• /
• 1996

This paper presents an indirect cutting force measuring system, which uses the current signals from the AC servo drive units of the horizontal machining center, with its applications to the adaptive regulation of the cutting forces in various milling processes and to the on-line monitoring of tool breakage. A typical model for the feed-drive control system of a horizontal machining center is developed to analyze cutting force measurement from the drive motor. The pulsating milling forces can be measured indirectly within the bandwidth of the current feedback control loop of the feed-drive system. It is shown that the indirectly measured cutting force signals can be used in the adaptive controller for cutting force regulation. The whole scheme has been embedded in the commercial machining center and a series of cutting experiments on the face cutting processes are performed. The adaptive controller reveals reliable cutting force regulating capability against the various cutting conditions. It is also shown that the tool breakage in milling can be detected within one spindle revolution by adaptively filtering the current signals. The effect of the cutter run-out has been considered for the reliable on-line detection of tool breakage.

• Journal of the Korean Society for Precision Engineering
• /
• v.14 no.10
• /
• pp.15-27
• /
• 1997

Quasti-static cutting force variations in milling process are measured indirectly using spindle motor current. Quasi-static sensitivity of the spindle motor current is higher than that of the feed motor current. Magnitude of the spindle motor current is independent of cutting direction. The linear relationship between the cutting force and the spimdle motor RMS current at various spindle rotational speed is obtained. Frequency/ Voltage(F/V) converter voltage is measured to identify the spindle speed and to determine the cutting force at various spindle speeds. Overload on the tool during milling process can be detected using the proposed indirect cutting force measurement. Based on these measurements, cutting force is regulated at a constant level by feedrate control.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1995.10a
• /
• pp.1054-1058
• /
• 1995

There have been many research works for the indirect cutting force measurement in machining process, which deal with the case of one-axis cutting process. In multi-axis cutting process, the main difficulties to estimate the cutting forces occur when the feed direction is reversed. This paper presents the indirect cutting force measurement method in contour NC milling processes by using current signals of servo motors. An artificial neural network (ANN) system are suggested. An artificial neural network(ANN) system is also implemented with a training set of experimental cutting data to measure cutting force indirectly. The input variables of the ANN system are the motor currents and the feedrates of x and y-axis servo motors, and output variable is the cutting force of each axis. A series of experimental works on the circular interpolated contour milling process with the path of a complete circle has been performed. It is concluded that by comparing the ANN system with a dynamometer measuring cutting force directil, the ANN system has a good performance.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.8
• /
• pp.1173-1182
• /
• 2001

Recent noticeable advances of CNC machine tools have considerably improved productivity and precision in manufacturing processes. However, in the respect of productivity some defects still remain because selection of machining conditions entirely depends on the experiences of programmers. Usually, machining conditions such as feed rate and spindle speed have been selected conservatively by considering the worst cases, and it has brought the loss of machining efficiency. Thus, the improvement of cutting force controller has been done to regulate cutting force constantly and to maximize feedrate simultaneously in case that machining conditions change variously. In this study, sliding mode control with boundary layer is applied to milling process for cutting force regulation and in a commercial CNC machining center data transfer between PC and PMC (programmable machine controller) of CNC machine is done using a standard interface method. And in the cutting force measurement, an indirect cutting force measuring system using current signal of AC servo is adopted in order not to use high-priced equipment like tool dynamometer. The purpose of this study is to maximize the productivity in milling process, thus its results can be applied to cases such as rough cutting process.

• Journal of the Korean Society for Precision Engineering
• /
• v.19 no.9
• /
• pp.66-73
• /
• 2002

Since cross-feed directional cutting force which is normal to machined surface directly influences the machined surface of the workpiece and total force loaded in cutter, it is necessary to estimate this force to control the roughness of the machined surface and total force in cutter. However, there have been difficulties in using the current existing in a stationary motor for cutting state prediction because of some unpredictable behavior of the current. Empirical approach was conducted to resolve the problem. As a result, we showed that the current and its unpredictable behavior are related to the infinitesimal rotation of the motor. Subsequently, the relationship between the current and the cutting force was identified with the error less than 50%. And, the estimation results of the two machine tools with different characteristics were compared to each other to confirm the validity of the presented estimation method and the characteristics of current of the stationary feed motor.

• Journal of the Korean Society for Precision Engineering
• /
• v.15 no.11
• /
• pp.9-20
• /
• 1998

In recent manufacturing process, the increase of productivity has been attempted by reducing machining time with the increase of cutting force. However, the excessive increase of cutting force can cause tool breakage and have a bad effect on both manufacturing machine and workpiece. Thus, it is necessary to estimate and control the cutting force in real time during the process. In this study, use of disturbance observer is proposed for the indirect cutting force estimation. The estimated cutting force is used for the real-time control of feedrate, making the actual cutting force follow the reference force command. Since the suggested method does not need an expensive sensor like a dynamometer, the method is expected to be used practically. Since the actual cutting force follow the reference force, resulting the reducing of the machining time the increase of productivity are also expected, and the quality of cutting surface has been improved due to the adjusted feedrate. Besides, an actual constant cutting force guarantees the prevention of tool breakage. To show the effectiveness of the suggested cutting force control method, an experimental setup has been made without sensor and applied to several workpieces. Experiments show that the suggested method is effective to cutting force control of a CNC machining center.

• Transactions of Materials Processing
• /
• v.15 no.1 s.82
• /
• pp.82-88
• /
• 2006

In this paper, the web-based monitoring system is developed for the effective process monitoring of mold manufacturing using web. In developed system, the cutting force for monitoring the manufacturing condition is measured using hall-sensor that is low cost and useful to be installed in a machine tool indirectly. Specially, the current of main spindle in a machine tool is converted into cutting force by various experiments. For effective web-based monitoring, the program which runs in the local computer of client is made to exchange message between a server and a client by making of ActiveX control and the result of manufacturing is shown on web-browser by Ch language. The developed system in this study is the foundation of establishing E-manufacturing in mold factory.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1996.04a
• /
• pp.276-280
• /
• 1996

This paper presents an indirect method for on-line measuring the cutting forces in contour NC milling processes by using the current signals of the servo drive motors. A Kaluman filler is used for estimating each of the load torques to the x, y-axis servo motors of a horizontal machining center. Then, the load torque induced by the friction force in the guidewayis estimated and subtracted from the total extermal torque, thus resulting in the load torque induced by the cutting force. A series of experimental works on the circular interpolated contour milling process shows good agrement between the cutting forces measured by the dynamometer and those estimated by the method presented in the paper.