• 한국기계가공학회지
• /
• 제13권2호
• /
• pp.108-116
• /
• 2014

Considering the run-out effect and cutting force coefficients, the cutting force profile of half immersion end-milling was analyzed in detail. The effects of three specific cutting-force coefficients and three edge-force coefficients are verified. Through a detailed investigation, it is proved that the radial cutting force coefficients and are the major factors which increase the cutting forces Fx and Fy in end-milling. However, the axial cutting force coefficients have no influence on the force Fx and Fy changes in end-milling. Also, the analyzed end-milling force model shows good consistency with the actual measured force with regard to Fx and Fy. Thus, this model can be used for the prediction of the force history in end-milling with run-out, and it incurs a different force history with different start and exit immersion angles as well as holding effects.

• 한국기계가공학회지
• /
• 제18권10호
• /
• pp.75-82
• /
• 2019

Few studies have been conducted regarding theoretical turning force modelling while considering cutting constant. In this paper, a new cutting force modelling technique was suggested which considers the specific cutting force coefficients for turning. The specific cutting force is the multiplication of the cutting force coefficient and uncut chip thickness. This parameter was used for experimental modelling and prediction of theoretical cutting force. These coefficients, which can be obtained by fitting measured average forces in several conditions, were used for the formulation of three theoretical cutting forces for turning. The cutting force mechanism was verified in this research and its results were compared with each of the experimental and theoretical forces. The deviation of force was incurred by a small amount in this model and the predicted force considering feed rate, nose radius, and radial depth shows a physical behavior in main force, normal force, and feeding force, respectively. Therefore, this modelling technique can be used to effectively predict three turning forces with different tool geometries considering cutting force coefficients.

• 대한기계학회논문집
• /
• 제15권6호
• /
• pp.2048-2061
• /
• 1991

본 연구에서는 이와 같은 구비조건과 문제점들을 해소하기 위하여 Fig.1과 같 이 볼 엔드 밀링의 절삭성과 경제적 절삭 속도식을 실용식의 형태로 표현하여 절삭조 건의 최적화를 위한 구속조건으로 설정하였고, 이를 자유곡면의 절삭경로 산출과정에 서 구속조건을 만족하면서 부품당의 생산비를 최소로 하는 스핀들속도와 이송속도를 결정하는 데에 적용하였다. 그리고 이는 실험모형에의 적용예를 통해 계산시간과 정 확도 및 절삭효과 등에 있어서 실용화의 가능성을 검토하였다. 이때 절삭력계를 해 석 함에 있어서는 기하학적 절삭 파라미터들에 대해 무차원적으로 정의된 절삭작용 누 적계수(accumulating coefficient)들을 이용하여 절삭력계를 선형화 된 실용식으로 표 현하였으며, 절삭 상수들과 절삭작용 누적계수들의 선형적 표현에 의해 평균 절삭력계 를 계산한 후, 토크 패턴 모델에 의해 절삭력 집중비를 구함으로써 실 절삭계의 주변 력(peripheral force), 드러스트, 토크, 동력 등을 예측하였다. 또한 절삭속도의 결 정에 있어서는 경제적 절삭속도 예측모델을 설정하여 가공비를 최소로 하는 절삭속도 를 선정토록 하였다.