• Journal of the Korean Geotechnical Society
• /
• v.17 no.4
• /
• pp.301-315
• /
• 2001

본 연구에서는 최근 5년간 국내 각 지역에서 채취한 802개의 절리면 시료에 대하여 전단시험을 실시하여 얻은 결과를 이용하여, 절리면의 여러 공학적 성질들을 조사, 연구하였다. 절리면 전단시험에서 얻어진 최대마찰각 및 잔류마찰각을 지체구조별, 암종별로 분류하고 통계적으로 구하였으며, Barton의 전단강도식의 입력변수인 JRC, JCS를 측정하고 Barton식의 적용성에 대해서도 검토하였다. 그 결과 설계의 기초자료로 활용할 수 있는 지역별, 주요 암종별 최대마찰각, 잔류마찰각을 제시하였다. 또한, JRC, JCS, 수직응력에 따른 마찰각과 전단강성 및 팽창각의 변화를 분석하였다. 마지막으로, Barton의 식에서 구한 이론적 전단강도와 이 실험에서 얻어진 전단강도를 비교한 결과, Barton의 경험식은 높은 상관도로 암석 절리면 전단강도를 예측할 수 있음을 확인하였다.

• Journal of the Korean Geotechnical Society
• /
• v.18 no.4
• /
• pp.229-238
• /
• 2002

This paper introduces the surface roughness parameter, Rs to the characterization of joint roughness and quantitatively illustrates the influence of joint roughness on the joint shear strength. A new peak shear strength criterion for rock joints using Rs is suggested. The results show that the surface roughness parameter, Rs can appropriately reflect the degree of roughness for the rock joint surfaces tested in this study A measuring interval of 2mm and profile length of 5cm can be used to characterize the joint roughness of the rock core size surfaces; however, the scale of fluctuation, $\delta_\alpha$ should be considered to extend the surface roughness parameter, Rs to the large-scale field rock joint surfaces. For the smooth joint roughness, sliding of the rock cores is the principal shear mechanism; however, the breakage of roughness from the rock cores is inferred for rougher joint roughness.

• Tunnel and Underground Space
• /
• v.17 no.3 s.68
• /
• pp.186-196
• /
• 2007

In this study, direct shear tests were carried out on the 30 rock joint samples in order to investigate the influence of roughness and normal stress on the shear behaviour. Joint roughness profiles were measured by use of 3D laser profiler, and then the samples were equally classified into three individual groups according to the roughness index of rock joints. Peak shear strength, residual shear strength, shear stiffness, dilation angle of rock joints were investigated in condition of five different constant normal load. Peak shear strength was increased as roughness index was increased, and the influence of roughness on strength was found to be more considerable in case of lower normal stress condition. Residual shear strength and shear stiffness were increased as roughness index and normal stress were increased. Finally dilation angle was decreased as normal stress was increased, but it was increased as roughness index was increased in the same normal stress condition.

• The Journal of Engineering Geology
• /
• v.20 no.3
• /
• pp.319-327
• /
• 2010

Surface roughness profiles were measured from 19 joint samples using a laser scanner, and Joint Roughness Coefficient (JRC) values were calculated from 30 sections in each sample. Although JRC values varied with the location of the section, the average JRC values from any three sections provides an adequate representation of the average JRC value for the entire surface well. Direct shear tests were performed on nine joints reproduced using molds of real joints in samples of gypsum. The peak friction angles (${\phi}_p$) showed a linear relationship with the average JRC values, yielding the following relationship: ${\phi}_p=41.037+1.046JRC$. However, the shear strengths measured by direct shear tests differed from those calculated using Barton's criterion. The relationship between calculated from direct shear tests and JRC measured from joint surfaces is defined as $JRC_R=f{\cdot}JRC$, and the correction coefficient f is was calculated as $f=3.15JRC^{-0.5}$, as calculated by regression. A modified shear-strength criterion, is proposed using the correction coefficient, ${\tau}={\sigma}_n{\cdot}tan(3.15JRC^{0.5}{\bullet}{\log}_{10}\frac{JCS}{{\sigma}_n}+{\phi}_b)$. This criterion may be effective in calculating the shear strength of moderately weathered rock joints and highly weathered rock joints with low strength and ductile behavior.

• Journal of the Korean Geotechnical Society
• /
• v.39 no.5
• /
• pp.5-12
• /
• 2023

This study investigates the existing models for estimating the shear strength of rock joints, presents related problems, and introduces a newly proposed model to overcome the problems. The results of many experimental tests show that the shear strength of a rock joint depends on many complex factors, including asperity angle, compressive strength, applied normal stress, friction angle, asperity cohesive strength, and progressive damage of asperities. However, the existing models do not account for these factors enough. To overcome these problems, Son (2020) developed a new model to estimate the shear strength of rock joints and confirmed its reliability by comparing with experimental results and existing models. In this paper, the developed model was used to investigate the various factors that affect the joint shear strength, and the results were compared and analyzed. Through this study, the factors that affect the shear strength of the rock joint could be identified in more detail.

• Tunnel and Underground Space
• /
• v.23 no.3
• /
• pp.203-211
• /
• 2013

Shear behavior of joint plane has been investigated considering the magnitude of normal stresses and initial surface roughness. Shear strength of joint plane has been measured by performing the multi-stage shear test in which applied normal stress level has been increased stepwise. Multi-stage shear test within the specified normal stress range has been repeated and two types of strength parameter variation have been observed: type 1 - both cohesion and friction angle decrease, type 2 - cohesion decrease and friction angle increase. Trends of strength parameter variation for the three rock types, gneiss, granite and shale, have been investigated and the influence of initial roughness of joint plane on the sequential shear strength change for the repeated multi-stage shear tests also has been analyzed.

• Tunnel and Underground Space
• /
• v.13 no.3
• /
• pp.169-179
• /
• 2003

Anisotropic shear strength of rock joints is studied based on the artificially fractured specimens using experimental and analytical methods. Series of direct shear tests are performed to obtain the strength, stiffness and friction angle of joints under various low normal stresses and shearing directions. The results of shear strength and stiffness show anisotropic value according to shearing direction under low normal stress specially less than 2.45 MPa. But, the effect of joint roughness on strength decreases with increasing normal stress. To estimate more effectively the peak shear strength under low normal stress, the modified Barton's equation is suggested.

• Tunnel and Underground Space
• /
• v.23 no.5
• /
• pp.401-412
• /
• 2013

Multi-stage shear test has been performed using joint specimens of gneiss, granite and shale to investigate the influence of micro-scale asperity change on the shear strength of joint plane. For each shear test asperity degradation characteristics of joint specimens of different joint surface strength have been analyzed by utilizing the optimum asperity parameter which can reflect the sequential asperity degradation. Elevation of joint surface profile has been measured and both the changes of asperity parameters and micro-scale asperity distribution have been investigated. Two distinctive variation modes of cohesion and friction angle have been delineated and major cause of shear strength parameter change has been analyzed by considering the micro-scale asperity angle change resulting from the abrasion, fracturing and regeneration of micro-scale asperities. Effects of micro-scale asperity variation on the joint shear strength have been also investigated.

• The Journal of Engineering Geology
• /
• v.22 no.1
• /
• pp.113-121
• /
• 2012

The mechanical characteristics of a fault gouge from near Mt. Kumjung in Kumjung-Gu, Busan, were estimated from laboratory tests on different joint models. Fault gouge samples and joint samples in biotite granite were obtained from boreholes in the study area that had penetrated small faults associated with the Dongnae and Yangsan faults. XRD and SEM analyses revealed that for the fault gouge consists of several clay minerals with tabular structure (kaolinite, montmorillonite, illite, sericite), which could cause the considerable reduction of shear strength when wet. The shear strength of the fault gouge was obtained from direct shear tests of the fault gouge itself and from direct shear tests of several natural/artificial joint surfaces coated with fault gouge. The results indicate that the reduction of shear strength is more abrupt for the joint surfaces coated with fault gouge compared with uncoated joint surfaces, and that the friction angle of the fault gouge between joint surfaces is much lower than the internal friction angle of the fault gouge itself. Fault gouges in contact with rock, therefore, could have a stronger negative effect on the stability of structures in rock masses than the fault gouge itself.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.10 no.3
• /
• pp.99-106
• /
• 1990

This study was aimed to see the effect of chemical grout on fresh granite joint shear strength. The grouting chemical used in this study was composed of 25% water glass. Direct shear tests were performed on the chemical filled joints, which had been made artificially with granite. The test results show that chemical grouted rock jonts have markedly reduced shear strength comparing with the ungrouted fresh joints and they sheared within chemical grout before the rock to rock contact had been established, while the ungrouted joint sheared between rock surfaces from the beginning of shear deformation. With chemical grouted joints the shear stress slowly reached its maximum without showing distinct peak shear strength. Therefore the shear stiffness of joints were decreased with increasing thickness of grout. but the shear strain at failure was increased with it.