• International Journal of Highway Engineering
• /
• v.13 no.4
• /
• pp.81-91
• /
• 2011

This study was conducted to evaluate the necessity of the anchor lug system in continuously reinforced concrete pavement(CRCP) by comparing longitudinal displacements of CRCPs with and without anchor lugs, and to investigate the effect of horizontal cracking on CRCP performance by measuring the vertical displacements. The measurements before and after the anchor lug section was separated were conducted for 12 days in June, and for 14 days in August after the abrupt displacements according to cutting disappeared, respectively. This short term measurement results showed that when anchor lugs were installed, a daily displacement variation at any location was less than 0.1mm; therefore, longitudinal movements were negligibly small. When there were no anchor lugs, longitudinal displacements mainly occurred near the free end and the displacement variation was small; therefore, an expansion joint system seems to be employed at a CRCP terminus without installing anchor lugs. However, further studies are needed to verify the terminus behavior due to annual temperature changes. The horizontal crack width variation was ignorable and did not affect the vertical displacement of the slab. Therefore, the horizontal crack did not delaminate the slab and did not seem to reduce the structural capacity and performance of CRCP.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.13 no.4
• /
• pp.805-812
• /
• 2009

In many intrusion detection applications, n-gram approach has been widely applied. However, n-gram approach has shown a few problems including unscalability and double counting of features. To address those problems, we applied n-gram augmented Naive Bayes with k-truncated suffix tree (k-TST) storage mechanism directly to classify intrusive sequences and compared performance with those of Naive Bayes and Support Vector Machines (SVM) with n-gram features by the experiments on host-based intrusion detection benchmark data sets. Experimental results on the University of New Mexico (UNM) benchmark data sets show that the n-gram augmented method, which solves the problem of independence violation that happens when n-gram features are directly applied to Naive Bayes (i.e. Naive Bayes with n-gram features), yields intrusion detectors with higher accuracy than those from Naive Bayes with n-gram features and shows comparable accuracy to those from SVM with n-gram features. For the scalable and efficient counting of n-gram features, we use k-truncated suffix tree mechanism for storing n-gram features. With the k-truncated suffix tree storage mechanism, we tested the performance of the classifiers up to 20-gram, which illustrates the scalability and accuracy of n-gram augmented Naive Bayes with k-truncated suffix tree storage mechanism.

• Journal of Aerospace System Engineering
• /
• v.15 no.5
• /
• pp.81-88
• /
• 2021

In general, a non-explosive nylon wire cutting-based holding and release mechanism has been used to store and deploy deployable solar panels of CubeSat. However, with this method, accessing the solar panel's access port for charging the cube satellite's battery and electrical inspection and testing of the PCB and payloads while the solar panel is in storage is difficult. Additionally, the mechanism must have a reliable release function in an in-orbit environment, and reusability for stow and deploy of the solar panel, which is a hassle for the operator and difficult to maintain a consistent nylon wire fastening process. In this study, we proposed a pin-puller-based solar panel holding and release mechanism that can easily deploy a solar panel without cutting nylon wires by separating constraining pins. The proposed mechanism's release function and performance were verified through a solar panel deployment test and a maximum separation load measurement test. Through this, we also verified the design feasibility and effectiveness of the pin-puller-based separation device.

• Journal of KIISE:Databases
• /
• v.30 no.3
• /
• pp.320-335
• /
• 2003

Location-Based Services(LBS) give rise to location-based queries of which results depend on the locations of moving objects. One of important applications of LBS is to examine tracks of continuously moving objects. Moving objects databases need to provide 3-dimensional indexing for efficiently processing range queries on the movement of continuously changing positions. An extension of the 2-dimensional R-tree to include time dimension shows low space utilization and poor search performance, because of high overlap of index nodes and their dead space. To solve these problems, we propose a new R-tree based indexing technique, namely TR-tree. To increase storage utilization, we assign more entries to the past node by using the unbalanced splitting policy. If two nodes are highly overlapped, these nodes are forcibly merged. It is the forced merging policy that reduces the dead space and the overlap of nodes. Since big line segments can also affect the overlap of index nodes to be increased, big line segments should be clipped by the clipping policy when splitting overfull nodes. The TR-tree outperforms the 3DR-tree and TB-tree in all experiments. Particularly, the storage utilization of the TR-tree is higher than the R-tree and R*-tree.

• Explosives and Blasting
• /
• v.34 no.4
• /
• pp.1-9
• /
• 2016

For underwater steel structure, cut that underwater shaped charge device that combines a spring hose, which is an external device of pressure resistance and flexibility with flexible shaped charge, was invented. As a basic experiment for an optimum condition design, an penetration performance was compared by external device shape. To evaluate the result of an experiment, image analysis was carried out after obtaining the model by using the liquid rubber for the penetrated steel plate. To simulate the penetrating process of shaped charge, the AUTODYN program has been used. As a result of analysis, while the average penetration depth of circular and square shaped external devices were similar, the penetration quality was more uniform in the case of circle. In addition, water infiltration occurred in square case, displacement and strain rate according to the increase of the water pressure were measured high.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.4
• /
• pp.25-33
• /
• 2018

In this paper, we propose an iterative self-interference (SI) channel estimation method for in-band full-duplex cellular systems that employ orthogonal frequency division multiple access (OFDMA) on downlink (DL) and single-carrier frequency division multiple access (SC-FDMA) on uplink (UL), as in Long Term Evolution (LTE) systems. The proposed method first acquires coarse estimates of SI channels using DL signals and UL pilots, which are known to the base stations, and then refines the estimates by consecutively exploiting averaging in the frequency domain and channel truncation in the time domain. In addition, the method enhances the estimates further by iteratively executing this estimation procedure, and does not require any radio resources dedicated to SI channel estimation. Simulation results demonstrate that by significantly improving the SI channel estimation performance without requiring exact knowledge of the SI channel length, the proposed method achieves UL channel estimation performance and signal-to-interference-plus-noise ratio (SINR) performance very close to those in perfect SI cancellation.

• Journal of Korean Society of Steel Construction
• /
• v.22 no.4
• /
• pp.355-363
• /
• 2010

The objective of this study is to examine the structural performance on the Rectangular Steel Tube Column-to-H Beam connections using one-side bolts and T-stub. Although a rectangular steel tube comparing with a H-shaped steel has many advantages and is more efficient, its application is limited due to the lack of experiences and connection details. Existing steel moment connections using the rectangular steel tube are mainly using through plate diaphragms. Its processing of construction is so complicated that it is hard to apply in the field. In this study, the structural performance and the earthquake capacity for T-stub connection with one-side bolts were investigated. And it is performed a comparative analysis of strength, rigidity, total rotation and energy absorption capacity for the various connection details.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.16 no.4
• /
• pp.30-37
• /
• 2002

This paper reports on the results of weathering test, tracking test and salt-fog test of various kinds of cycloaliphatic epoxy systems. UV irradiation dramatically induced the loss of surface hydrophobicity due to the chain scission attack at the surface under UV irradiation. It could be seen that samples containing an UV absorbent/antioxidant and a silicone oil additive have a good performance in weathering test, while ATH(alumina tri-hydrate) filled ones have high resistance against tracking failure than others. Under salt fog chamber test, specimens mixed with silicone oil are able to suppress leakage current development. It was thought that silicone oil mixed into cycloaliphatic epoxy system could lead to lower the surface energy and to retain hydrophobic properties for a long time, which are desirable for outdoor use.

• Journal of Korean Society of Steel Construction
• /
• v.14 no.5 s.60
• /
• pp.647-656
• /
• 2002

High-strength steel in steel bridges is the key to achieving cost-efficiency because it facilitates lightweight construction and rationalizes structure. The future of high-strength steel is bright, with its use projected to expand. As such, it is necessary to evaluate precisely various factors affecting the process of fabricating high-strength steel, i.e., welding heat, strain hardening, and weldability and performance of the welded joints. This study therefore performed the maximum hardness test and y-groove weld crack test using welding processes such as SAW, FCAW, and GMAW, in order to investigate the welding performance and characteristics of welded Joints or high-strength steel produced in Korea such as SM570, POSTEN60, and POSTEN80. In addition, a series of welding tests was carried out to estimate the tensile strength, bending characteristics, absorbed energy, and hardness in welded joints.

• Korean Chemical Engineering Research
• /
• v.49 no.6
• /
• pp.745-751
• /
• 2011

In this study, zinc or cerium exchanged zeolite was introduced to develop a novel anti-corrosion pigment. The primer paint was made using them and was coated on galvanized(GI) steel. The anti-corrosion performance was measured using electrochemical impedance spectroscopy(EIS). And scanning vibrating electrode technique(SVET) was employed to observe the cut-edge corrosion process of the coated GI steel. From EIS and SVET results, it could be confirmed that Ce ion-exchanged zeolite showed the anti-corrosion performance higher than Shieldex C303 and Zn ionexchanged zeolite. Finally, it was found that metal ion-exchanged zeolite may provide new possibility as the smart cathodic corrosion inhibitor delivery systems on galvanized steels.