• Journal of Surface Science and Engineering
• /
• v.55 no.6
• /
• pp.363-367
• /
• 2022

Transparent ZnO/Ti/ZnO (ZTZ) tri-layered films were prepared with radio frequency (RF) and direct current (DC) magnetron sputtering on the glass substrate. The thickness of the ZnO and Ti films was kept at 50 and 10 nm to consider the effect of the electron irradiation on the crystallization and optoelectrical properties of the films. From the XRD spectra, post-depostion electron irradiated films showed the characteristic peaks of ZnO(002) and Ti(200), respectively. the observed grain size of the ZnO(002) and Ti(200) enlarged up to 18.27 and 12.16 nm at an irradiation condition of 750 eV. In the figure of merit which means an optoelectrical performance of the films, as deposited films show a figure of merit of 2.0×10^-5 𝛺^-1, while the films electron irradiated at 750 eV show a higher figure of merit of 5.7×10^-5 𝛺^-1.

• Korean Journal of Metals and Materials
• /
• v.46 no.10
• /
• pp.634-645
• /
• 2008

In this study, surface composites were fabricated with Fe-based amorphous alloy powders and VC powders by high-energy electron beam irradiation, and the correlation of their microstructure with hardness and fracture toughness was investigated. Mixture of Fe-based metamorphic powders and VC powders were deposited on a plain carbon steel substrate, and then electron beam was irradiated on these powders without flux to fabricate surface composites. The composite layers of 1.3~1.8 mm in thickness were homogeneously formed without defects and contained a large amount (up to 47 vol.%) of hard $Cr_2B$ and $V_8C_7$ crystalline particles precipitated in the solidification cell region and austenite matrix, respectively. The hardness of the surface composites was directly influenced by hard $Cr_2B$ and $V_8C_7$ particles, and thus was about 2 to 4 times greater than that of the steel substrate. Observation of the microfracture process and measurement of fracture toughness of the surface composites indicated that the fracture toughness increased with increasing additional volume fraction of $V_8C_7$ particles because $V_8C_7$ particles effectively played a role in blocking the crack propagation along the solidification cell region heavily populated with $Cr_2B$ particles. Particularly in the surface composite fabricated with Fe-based metamorphic powders and 30 % of VC powders, the hardness and fracture toughness were twice higher than those of the surface composite fabricated without mixing of VC powders.

• Composites Research
• /
• v.34 no.1
• /
• pp.23-29
• /
• 2021

Commercialized carbon fiber obtained from polyacrylonitrile(PAN) precursor is subjected to oxidation stabilization at 180 to 300℃ in air atmosphere and carbonization process at 1600℃ or lower in inert gas atmosphere. Both of these processes use a lot of time and high energy, but are essential and important for producing high-performance carbon fibers. Therefore, in recent years, an alternative stabilization technology by being assisted with various other energy sources such as plasma, electron beam and microwave which can shorten the process time and lower energy consumption has been studied. In this study, the PAN precursor was stabilized by using plasma treatment and heat treatment continuously. The morphology, structural changes, thermal and physical properties were analyzed using Field emission scanning electron microscopy(FE-SEM), X-ray diffraction(XRD), Fourier transform infrared(FT-IR), Thermogravimetric analysis(TGA) and Favimat.

• Journal of Surface Science and Engineering
• /
• v.54 no.1
• /
• pp.25-29
• /
• 2021

The fabrication of nanopore membrane by deposition of Al2O3 film using electron-beam evaporation, which is fast, cost-effective, and negligible dependency on substance material, is investigated for potential applications in water purification and sensors. The decreased nanopore diameter owing to increased wall thickness is observed when Al2O3 film is deposited on anodic aluminum oxide membrane at higher deposition rate, although the evaporation process is generally known to induce a directional film deposition leading to the negligible change of pore diameter and wall thickness. This behavior can be attributed to the collision of evaporated Al2O3 particles by the decreased mean free path at higher deposition rate condition, resulting in the accumulation of Al2O3 materials on both the surface and the edge of the wall. The reduction of nanopore diameter by Al2O3 film deposition can be applied to the nanopore membrane fabrication with sub-100 nm pore diameter.

• Journal of Advanced Navigation Technology
• /
• v.24 no.6
• /
• pp.593-600
• /
• 2020

The equipment for marine IoT service have to overcome the effect of seawater. Furthermore, the free floating transmitter in seawater will be less affected by the seawater environment. The results of the design and fabrication of antenna, which is embedded in buoy, are shown in this research. The proposed antenna is used to supervise the states of fishing gears in monitoring system for real-name system of electric fishing gear. The selected frequency band of the proposed antenna is 920 MHz, and PCB pattern type is selected for subminiature and light weight. It is confirmed that RF characteristics is more degraded, however, the radiation is gradually upward as the contact surface of buoy with seawater is more broaden through the simulation results. That is, the RF performance of the proposed antenna is more deteriorated but beam radiation characteristics is more suited the marine IoT, the seawater effect is more increased. It is expected that the proposed antenna will contribute the implementation of IoT network based on low power wide area (LPWA) when the degradation of RF performance will be settled.

• Journal of the Korea Institute of Information Security & Cryptology
• /
• v.32 no.5
• /
• pp.965-973
• /
• 2022

As IoT(Internet of Things) devices become common, many algorithms have been developed to protect users' personal information. The laser fault injection attack that threatens those algorithms is a side-channel analysis that intentionally injects a laser beam to the outside of a device to acquire confidential information or abnormal privileges of the system. There are many studies to determine the timing of fault injection to reduce the number of necessary fault injections, but the location to inject faults is only repeatedly searched for the entire area of the device. However, when fault injection is performed in an algorithm-independent area, the attacker cannot obtain the intended faulted statement or attempt to bypass authentication, so finding areas vulnerable to fault injection and performing an attack is an important consideration in achieving a high attack success rate. In this paper, we show that a 100% attack success rate can be achieved by determining the vulnerable areas for fault injection by using electromagnetic and thermal information generated from the device's chip. Based on this, we propose an efficient fault injection attack system.

• Journal of the Korean Society for Heat Treatment
• /
• v.36 no.5
• /
• pp.298-302
• /
• 2023

Transparent and conducting tungsten (W) doped indium oxide (IWO) thin films were deposited on the glass substrate by using RF magnetron sputtering and then electron irradiation was conducted to investigate the effect of electron irradiation on the optical and electrical properties of the films. The electron irradiated films showed three x-ray diffraction peaks of the In₂O₃ (222), (431) and (046) planes and the full width at half maximum values are decreased as increased electron irradiation energy. In the atomic force microscope analysis, the surface roughness of as deposited films was 1.70 nm, while the films electron irradiated at 700 eV, show a lower roughness of 1.28 nm. In this study, the figure of merit (FOM) of as deposited films is 2.07 × 10^-3 Ω^-1, while the films electron irradiated at 700 eV show the higher FOM value of 5.53 × 10^-3 Ω^-1. Thus, it is concluded that the post-deposition electron beam irradiation is the one of effective methods to enhance optical and electrical performance of IWO thin films.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.7 no.1
• /
• pp.70-75
• /
• 1997

An improved technique based upon an electron beam evaporation system has been developed to prepare cubic thin films In crystalline semiconductors. Zinc blonde CdSe epilayers were grown on GaAs(100) substrate by an e-beam evaporation method. The lattice parameter obtained from (400) reflection is $6.077\AA$, which is in excellent agreement with the value reported in the literature for zinc blonde CdSe. The orientation of the as-grown CdSe epilayer is determined by electron channeling patterns. The crystallinity of epitaxial CdSe layers were investigated on the double crystal X-ray rocking curve. The carrier concentration and mobility of epilayers deduced by Hall effect measurement are about $10^{18}{\textrm}{cm}^{-3}$, $10^2\textrm{cm}^2/V{\cdot}sec$ at room temperature, respectively. The photocurrent spectrum peak of the epilayer at 30 K exhibits a sharp change at 1.746 eV due to the free exciton of cubic CdSe.

• Korean Journal of Materials Research
• /
• v.33 no.11
• /
• pp.497-501
• /
• 2023

ZnO/Cu/ZnO (ZCZ) thin films were deposited at room temperature on a glass substrate using direct current (DC) and radio frequency (RF, 13.56 MHz) magnetron sputtering and then the effect of post-deposition electron irradiation on the structural, optical, electrical and transparent heater properties of the films were considered. ZCZ films that were electron beam irradiated at 500 eV showed an increase in the grain sizes of their ZnO(102) and (201) planes to 15.17 nm and 11.51 nm, respectively, from grain sizes of 13.50 nm and 10.60 nm observed in the as deposited films. In addition, the film's optical and electrical properties also depended on the electron irradiation energies. The highest opto-electrical performance was observed in films electron irradiated at 500 eV. In a heat radiation test, when a bias voltage of 18 V was applied to the film that had been electron irradiated at 500 eV, its steady state temperature was about 90.5 ℃. In a repetition test, it reached the steady state temperature within 60 s at all bias voltages.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.23 no.5
• /
• pp.97-102
• /
• 2023

In this paper, we fabricated transmitting and receiving antennas to realize the low cost radar using two receiving antennas and investigated their characteristics. The antennas are designed with MPA(Microstrip Patch Array) structure for the beam concentration in horizon direction and low cost and used Taylor array pattern synthesis to suppress sidelobes. As a results of measurement in the 24GHz ISM band(24.0-24.25GHz), our using band, antenna gains are placed between 15.2 dBi and 16.26 dBi which are satisfied with the design specification of higher than 15dBi and lower than 17dBi. The sidelobes are -13.15 dBc, -13.1 dBc and -12.8 dBc at the operating frequencies of 24.0 GHz, 24.125 GHz and 24.25 GHz repectively, which are satisfied with the specification of lower than -10 dBc.