• Proceedings of the Korea Contents Association Conference
• /
• 2006.05a
• /
• pp.470-474
• /
• 2006

In the case of dryer tendency that select directly without being serviced with salesperson's opinion specially because it does Purchase with sufficient knowledge is package of goods being high and labeling for goods of consumers are indicated to very important element This development wishes to escape and use "Seramik heater" and apply electromagnetic waves cover skill to be Hair Drier that head of a family electromagnetic waves are happened in method and household electric appliance that can raise sexual intercourse of circle infrared rays and High efficiency quantity of heat and coincide in high efficiency and All function anger request in existent metal heat ray.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.9
• /
• pp.924-930
• /
• 2003

In this paper, a novel miniaturized microstrip duplexer with attenuation pole is proposed. A three-pole microstrip CT(Cascade Trisection) two bandpass filters have each asymmetrically prescribed transmission zero are design and fabrication. This CT bandpass filter changes coupling structure, which not only shifts the location of attenuation poles but also improves skirt characteristics. The duplexer results of measurement with the cross coupling CT bandpass filters has been yielded better isolation and sharper skirt behavior than that with a conventional bandpass filter. The results of measurement are almost similar to those of simulation results.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.1
• /
• pp.9-15
• /
• 2011

In this paper, we designed and fabricated a dual-band bandpass filter which can control upper and lower bandwidth using the transformed E-shaped dual-mode resonator. The filter is made the coupling between even-mode not to affect odd-mode resonant frequency by the transformed resonator to control upper bandwidth effectively. The cross coupling between input and output feed lines was employed to improve stopband characteristic. The bandpass filter has been designed to indicate the same bandwidth at center frequency 2 GHz and 3 GHz to show to control bandwidth.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.4
• /
• pp.418-426
• /
• 2008

In this paper, investigations on the impedance characteristics of a DGS(Defected Ground Structure) slot in the groud plane of microstripline are presented in spectral domain and applied to the characteristic improvement of stepped impedance microstrip low pass filter(LPF). In this method, expressions for the impedance of a DGS slot are derived from self-reaction of the angular spectrum of plane waves and the discontinuity in the modal voltage. The numerical results are compared with those of the rigorous full-wave method and are shown to produce reasonably accurate data. And the stepped impedance microstrip low pass filter is designed and fabricated with the uniform and nonuniform DGS slots for improving the frequency responses. The experiments show that the proposed filter with slots in the ground plane has a wider stopband and sharper cutoff response.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.12 s.103
• /
• pp.1186-1193
• /
• 2005

In this paper, a new 3 dB branch line hybrid using asymmetric spiral-shaped defected ground structure(DGS) microstrip is proposed. The proposed branch line hybrid suppresses the 2nd and the 3rd harmonic component effectively. Also a DGS $\lambda$/4 bias line that can suppress high frequency harmonics as well as low frequency intermodulation component is proposed. With the harmonic termination tuner using the proposed hybrid and the harmonic blocking bias line, the 2nd and the 3rd harmonic components of the fabricated amplifier that operated in IMT-2000 basestation transmitting band were suppressed up 25 dB and 27 dB, respectively. The proposed harmonic load-pull setup of amplifier is more easily accomplished with proposed circuits than the previous.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.3
• /
• pp.343-351
• /
• 2008

In this paper, a spiral shaped common mode filter(CMF) embedded in a flexible printed circuit board(FPCB) is proposed for a multi-function cable. The CMF embedded in a FPC cable presents a new concept as a multi-function cable by the common mode rejection characteristics without a surface mounted device(SMD) CMF. The embedded CMF has a wideband common mode rejection bandwidth and an enhanced differential mode characteristics compared to conventional CMFs that use a magnetic material such as a ferrite of high loss. The proposed CMF of 3 turn inductors has a common mode rejection bandwidth from 0.4 GHz to 3.12 GHz and has 1.95 dB at 3 GHz, 6.97 dB at 8 GHz improvements of a differential mode insertion loss compared to the commercial LTCC(Low Temperature Co-fire Ceramics) CMFs.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.9
• /
• pp.912-918
• /
• 2011

In this paper, a composite right-/left-handed(CRLH) rectangular waveguide satisfying a balanced condition above the cut-off frequency is presented. The proposed structure consists of one shorted stub and two twisted H-plane irises which produce an effectively negative permeability and permittivity, respectively. The CRLH structure can independently control the series and shunt resonance frequencies of a CRLH transmission line which determine the left-handed(LH) and right-handed(RH) bands due to a minimized coupling between a shorted stub and twisted H-plane irises. Thus, the design of the CRLH waveguide satisfying a balanced condition is possible. To analyze the CRLH structure, a crossly connected equivalent circuit is derived. The simulated and measured results confirm that the proposed CRLH waveguide has a transmission property without a band gap among the LH and RH bands.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.19 no.12
• /
• pp.1462-1469
• /
• 2008

This paper proposes the design method based on the Composite Right/Left-Handed(CRLH) structure to miniaturize and enhance the rejection performance in the stopband of the bandpass filter for a VHF band($169{\sim}211\;MHz$). For realization, we used the 0-th order resonance point of the CRLH and the simple theory of Inverter as coupling. The proposed technique is validated by the performance predictions and experiments, (Insertion loss <2 dB, $S_{11}$< -15 dB, suppression of up to the 3rd harmonic) and it is found out that the suggested method enables the size reduction of around 60 % from the conventional filters such as the parallel edge coupled type.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.10 no.2
• /
• pp.157-168
• /
• 1999

In this paper the new channel allocation method which is important in designing mobile radio system, is proposed. If the channel is allocated by time-frequency-code sliced and using DAMA scheduler, the blocking probability is lower than TA channel allocation method. With traffic load $\rho$=0.8 and 2% of blocking probability, TFS method can allocate 36 slices compared to 11 slices in TA method. At traffic load $\rho$=0.9 and 1% of blocking probability, the maximum available slices are 13 in TA method, but in TFS method 40 slices are allocated to user, so TFS method is better frequency availability by 3.75 times than TA method. TFS method could be suitable for system planning to multirate communication users.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.2
• /
• pp.161-166
• /
• 2009

In this paper, we propose the internal mobile antenna for TDMB and KPCS. The proposed antenna is made of different dielectric substrate and it has small size ($45{\times}8{\times}8\;mm$, about 2.8 cc) for mobile device. TDMB antenna is designed spiral structure that makes maximum current for each cell and KPCS antenna is PIFA that is usually used for internal antenna. In order to compensate length of resonance TDMB antenna has a large inductor above 100 nH. In this case, the inductor isolate KPCS signal at TDMB by cutting high frequency. Also the antenna has good isolation because TDMB radiator is parasitic element in KPCS band. We simulated the antenna by using CST microwave studio and measured performance of the antenna in anechoic chamber Proposed antenna has $-6{\sim}-14\;dBi$ gain for TDMB and $-3.5{\sim}-5\;dBi$ gain for KPCS.