• 한국전산유체공학회지
• /
• 제11권4호
• /
• pp.48-55
• /
• 2006

A computational study was carried out in order to investigate aerodynamic characteristics on leading edge sweepback angles of Flying-Wing configurations. The viscous-compressible Navire-Stokes equation and Spalart-Allmaras turbulence model of the commercial CFD code were adopted for this computation analysis. This investigation examined aerodynamic characteristics of three different types of leading edge sweepback angles: $30^{\circ}C,\;35^{\circ}C\;and\;40^{\circ}C$. The freestream Mach number was M=0.80 and the angle of attack ranged from ${\alpha}=0^{\circ}C\;to\;{\alpha}=20^{\circ}C$. The results show that the increases in sweepback angle of the Flying-Wing configuration creates more efficient aerodynamic performance.

• 한국전산유체공학회지
• /
• 제11권4호
• /
• pp.56-61
• /
• 2006

Numerical simulation has been performed to investigate the characteristics of the mist flow through the fire suppression nozzles. The commercial CFD software, FLUENT with the proper modeling was applied for analyzing both the internal and external flow of the spray nozzles. Computations were made for the full cone nozzle in the operation range of the low pressure and high flow-rate. To validate the present computational procedure, numerical results are compared with measurements in terms of K-factor, SMD, axial spray velocity and spray angles. Numerical results suggested that the present numerical model can be used as an adequate tool for a design purpose of mist-spray nozzles.

• 한국전산유체공학회지
• /
• 제12권2호
• /
• pp.32-36
• /
• 2007

NUFLEX is a general purpose program for the analysis 3D thermo/fluid flow and pre/post processor in a complex geometry. NUFLEX is composed of various physical models, such as phase change(solidification/melting) and spray, MHD(Magneto Hydraulic Dynamics) models. It is possible to simulate continuous cast iron process and spray droplet breakup/collision phenomenon. For the verification of these models, compared with the experimental data and commercial CFD code's results. The results show good agreements with experimental and comercial CFD codes's results.

• 한국전산유체공학회지
• /
• 제20권1호
• /
• pp.57-64
• /
• 2015

This paper describes a volume of fluid(VOF) method, mRHRIC for the simulation of free surface flows around ship hulls and provides its validation against benchmark test cases. The VOF method is developed on the basis of RHRIC method developed by Park et al. that uses high resolution differencing schemes to algebraically preserve both the sharpness of interface and the boundedness of volume fraction. A finite volume method is used to solve the governing equations, while the realizable ${\kappa}-{\varepsilon}$ model is used for turbulence closure. The present numerical results of the resistance performance tests for DTMB5415 and KCS hull forms show a good agreement with available experimental data and those of other free surface methods.

• 한국전산유체공학회지
• /
• 제20권1호
• /
• pp.26-31
• /
• 2015

A grid generation program for specific problems is introduced. The program allows users to easily generate grid system for specific geometry such as an airfoil, cylinder, wedge, flat plate, and nozzle. Generating grid system for those problems can be proceeded with minimum user inputs such as geometry-defining parameters and grid-defining parameters. By using this program learning stage for preprocessing of CFD application can be efficiently shorten and novice students can learn and acquire experience by trying out grid generation and CFD solution by themselves.

• 한국전산유체공학회지
• /
• 제17권1호
• /
• pp.16-22
• /
• 2012

Acoustic pressure field around the centrifugal fan is predicted by a aero-acoustic splitting method. Unsteady flow field is obtained by solving the incompressible Navier-Stokes equations using commercial code, while the acoustic waves generated inside the centrifugal fan and shroud are predicted by solving the far field acoustics analysis. Computational results show that the acoustic waves of BPF tone are generated by interactions of the blades with the shroud. Acoustic results is validated by experimental results This paper describes the influence of geometric parameters on the noise generation from the section of blades and shroud. One of the effective ways to reduce BPF noise is optimization method using Genetic Algorithm, which effectively minimize eccentricity, is suggested. New improving design was developed by optimization method.

• 한국전산유체공학회지
• /
• 제17권1호
• /
• pp.23-28
• /
• 2012

The pressure transient inside the passenger cabin of high-speed train has been simulated using computational fluid dynamics(CFD) based on the axi-symmetric Navier-Stokes equation. The pressure change inside a train have been calculated using first order difference approximation based on a linear equation between the pressure change ratio inside a train and the pressure difference of inside and outside of the train. The numerical results have been assessed for the KTX train passing through a 9km long tunnel of Wonju-Kangneung line at the speed of 250km/h assuming that the train is satisfying the train specification for airtightness required by the regulation.

• 한국전산유체공학회지
• /
• 제15권4호
• /
• pp.109-114
• /
• 2010

In a fan design, CFD analysis, which is very useful for mechanical design relating to the heat and fluid dynamics, is one of the most popular tools. However, since the CFD analysis is conventionally carried out with the constant fan speed condition, the speed change, induced by the air flow rate and motor characteristics, is hardly modeled. And, consequently, the remarkable difference exist between analysis and experimental results. In this paper, we has proposed a method of setting the varying fan speed as a boundary condition considering air flow rate and motor torque-speed characteristics. The effectiveness of the proposed method is verified by comparison with experimental results.

• 한국전산유체공학회지
• /
• 제15권4호
• /
• pp.53-59
• /
• 2010

Preliminary design of a ground plate, a device installed close to the aircraft model for wind tunnel test to simulate the ground effect, was performed by a numerical simulation. A two-dimensional numerical study was performed initially to decide the optimal leading edge and flap configurations. Then, three-dimensional studies were conducted to decide the optimal flap deflection angle for pressure distribution reduction since the plate and the plate supporting system generate static pressure difference between the upper and lower flow regions. Three-dimensional simulation additionally studied the effect of the clearance between the plate and the wind tunnel side wall. For the efficiency of computation, half model was simulated and a symmetric boundary condition was applied on the center plane. Based on the preliminary design, a ground plate was designed, manufactured and tested at the Korea Aerospace Research Institute(KARI) wind tunnel. The measured pressure differences versus flap deflection angle agreed well with the predicted results.

• 한국전산유체공학회지
• /
• 제15권4호
• /
• pp.60-66
• /
• 2010

Unsteady Reynolds Averaged Navier-Stokes(URANS) and Large Eddy Simulation(LES) simulation of an axial flow fan are calculated upon same conditions and computational grids in order to study aeroacoustic noise of an axial flow fan numerically. Results of computed performance and predicted noise are compared with those of measurement. Both performances show accurate results with a significant difference of less than 5%. However, noise of LES result is more close to measured noise qualitatively than URANS. Levels of tonal noises of both LES and URANS are quite similar with those of measured at BPF(Blade Passing Frequency) in sound spectrum. However, as leading edge separation and tip vortex shedding phenomena of LES are showed more clearly than those of URANS, sound level of broadband noise of LES corresponds better than that of URANS, especially.