• Journal of the Earthquake Engineering Society of Korea
• /
• v.6 no.4
• /
• pp.39-49
• /
• 2002

In this paper, the characteristics of RB(rubber bearing) were studied by various prototype tests on RB with low hardness rubber. The characteristics of RB were tested on displacements, repeated cycles, frequencies, vertical pressures, temperature, vertical stiffness and the capability of shear deformation. The prototype test showed that the displacement and vertical pressures were the most governing factors influencing on characteristics of RB. The effective stiffness and equivalent damping of RB showed small increment in high frequency range. After the repeated cyclic test with 50's cycles, the effective stiffness and equivalent damping of RB were almost constant compared with those of the 1st cycles due to low hysteretic damping. The shear modulus of RB was reduced after large deformation, and this value of RB was partly recovered after 40 days. Finally, the shear failure test of RB was conducted, the prototype was failed over 490% of shear strain, and real size RB was failed over 430% of shear strain.

• The Korean Journal of Rheology
• /
• v.2 no.2
• /
• pp.19-27
• /
• 1990

레이저와 타이머장치를 설치한 낙구식 점도계에서 구와 니들이 주어진 구간을 통과 하는 시간을 측정하여 종말속도를 정확히 결정하였고 점성이 작은유체와 낮은 전단률 점성 과 영전단률 점성은 속이 빈 알루미늄 구와 니들이 이용하여 측정하였다. 알루미늄 구와 니 들의 속에 철분을 삽입하여 밀도를 다양하게 변화시켰다. 낙구식 점도계에서 측정한 낮은 전단률 점성과 영 전단률 점성 그리고 모세관점도계에서 측정한 높은전단률 점성과 무한 전 단률 점성을 이용하여 점탄성 유체의 특성이완시간을 결정하였다. 실린더 속의 시험용 유체 를 교란시키지 않고 밑면에 떨어진 구를 회수하는 장치를 설치하였다. 이 장치는 하나의 구 로써 점탄성유체의 특성확산시간을 측정하는데 대단히 효과적이었다. Polyacrylamide Separan AP-273 용액(농도 500-200 wppm)의 특성이안시간과 특성화산시간을 낙구식 점도 계와 모세관 점도계의 실험결과를 이용하여 결정하고 폴리며 용액의 퇴화 현상을 실험적으 로 분석하였다.

• Journal of the Korean GEO-environmental Society
• /
• v.17 no.3
• /
• pp.13-19
• /
• 2016

The ultrasonic waves for monitoring concrete materials have been used to investigate the setting and hardening process of concrete. This paper presents the application of bender elements for monitoring the hardening properties of Controlled Low Strength Material (CLSM) and the characterization of shear waves in CLSM according to curing time. To ensure the early age properties and flow, the CLSM consists of CSA cement, sand, silt, water, fly ash, and accelerator. In addition, three different type specimens according to fine contents are mixed. A couple of bender elements are installed at the wall of measurement cell and the CLSM specimen are prepared at the measurement cell for 28 days. Experimental results show that the resonant frequency and shear wave velocities increase with an increase in the curing time, regardless of the fine contents. Up to ten hours, the amplitudes of shear waves also increase, and the resonant frequency and shear wave velocities at the same time increase as the fine contents increase. The shear wave measurement technique using the bender elements may be effectively used to evaluate the hardening properties of CLSM along the curing time.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2010.11a
• /
• pp.577-580
• /
• 2010

Coaxial injectors using GCH4/LOx as propellants was designed with shear(gas)/shear(liquid) type and shear(gas)/swirl(liquid) type. Spray characteristics were investigated by cold flow test. Spray patterns of the shear/shear and the shear/swirl type injectors were like a spout of water and hollow cone, respectively. Atomization efficiency of the shear/swirl type injector was better than atomization efficiency of the shear/shear type injector.

• The Korean Journal of Rheology
• /
• v.10 no.1
• /
• pp.24-30
• /
• 1998

솔젤법을 이용하여 단분산의 실리카 입자를 제조하고 농도변화에 따른 실리카 분산 액의 유변학적 거동을 해석하였다. 단분산 실리카 입자의 제조는 솔젤법을 이용한 액상반으 으로 제조하였고 입자의 안정화를 위하여 입자표면에 실란커플링제를 코팅하여 유기용매에 서 안정성을 갖도록 하였다. 분산액의 농도에 따른 유변학적 거동을 조사하기 위하여 부피 분율( )이 0.05인 희박 분산계로부터 =0.55의 고농도 분산계를 제조하였다. 솔젤법을 통하 여 단분산 실리카 입자를 성공적으로 제조하였으며 실란커플링제인 ${\gamma}$-methacryloxypropyl triethoxysilane로 입자의 표면을 화학적 방법으로 처리하여 유기용매 상에서 알킬기의 작용 에 의한 hard-sphere'특성을 나타내도록 하였으며 동시에 분산안정성을 유지할수 있었다. 입자 분산계는 =0.25이하의 부피농도에서는 분산용매와 같은 뉴톤거동을 보여주었으며 이 이이상의 농도에서는 비뉴톤거동인 전단담화(shear thinning)현상과 high shear limiting viscosity를 나타내었다. 이결과는 Krieger-Dougherty 식을 따름이 확인되었으며 부피분율 =0.50정도까지도 이식이 잘적용됨을 확인하였다. 부피분율 =0.50 이상의 고농도 입자 분산계 는 급격한 점도의 증가와 함께 전단담화와 전단탁화(shear thickening)현상이 모두 관찰되었 다. 특히 전단탁화를 일으키는 특헝전단변형률(cr)이하의 전단변형률에서는 안정되고 빠른 점성반응(viscous response)을 보여주었으나 특성 전단변형률 부근과 이상의 전단변형률 영 역에서는 매우 불안한 거동이 보여짐을 확인하였다. 그러나 이러한 점도 거동은 가역적이며 전단변형률을 증가시킬때와 감소시킬 때의 유변학적 거동이 거의 일치하였다.

• KSCE Journal of Civil and Environmental Engineering Research
• /
• v.33 no.1
• /
• pp.181-194
• /
• 2013

Landslides are known as gravitational mass movements that can carry the flow materials ranging in size from clay to boulders. The various types of landslides are differentiated by rate and depositional features. Indeed, flow characteristics are observed from very slow-moving landslides (e.g., mud slide and mud flow) to very fast-moving landslides (e.g., debris avalanches and debris flows). From a geomechanical point of view, shear-rate-dependent shear strength should be examined in landslides. This paper presents the design of advanced ring-shear apparatus to measure the undrained shear strength of debris flow materials in Korea. As updated from conventional ring-shear apparatus, this apparatus can evaluate the shear strength under different conditions of saturation, drainage and consolidation. We also briefly discussed on the ring shear apparatus for enforcing sealing and rotation control. For the materials with sands and gravels, an undrained ring-shear test was carried out simulating the undrained loading process that takes place in the pre-existing slip surface. We have observed typical evolution of shear strength that found in the literature. This paper presents the research background and expected results from the ring-shear apparatus. At high shear speed, a temporary liquefaction and grain-crushing occurred in the sliding zone may take an important role in the long-runout landslide motion. Strength in rheology can be also determined in post-failure dynamics using ring-shear apparatus and be utilized in debris flow mobility.

• Tunnel and Underground Space
• /
• v.17 no.3 s.68
• /
• pp.203-215
• /
• 2007

Stability and mechanical deformation behavior of rock masses are highly dependent on the mechanical characteristics of contained discontinuities. Therefore, mechanical characteristics of the discontinuities should be considered in the design of tunnel and underground structures. In this study, direct shear tests for rough granite joints were carried out under constant normal stiffness conditions. Effects of initial normal stress, shear velocity, and surface roughness on the characteristics of shear strength and deformation behaviors were examined. Results of shear testing under constant normal stiffness conditions reveal that shear behaviors could be classified into two categories, based on the amount of decrease in shear stress at the Int peak shear stress. With initial normal stiffness increasing, it turned out that shear displacement at peak stress and the first peak shear stress increased, however friction angle and friction coefficient showed decrease. In case of shear stiffness and average friction coefficient, it turned out that they are not dependent on the initial normal stress. Minor effects of shear velocity on rough joints were observed in several shear quantities. However, the effects of shear velocity were insignificant regardless of the normal stress increase. Change of shear strength and deformation characteristics on joint roughness were examined, however, it turned out that the variations were attributed to deviation of shear test specimens.

• Ecology and Resilient Infrastructure
• /
• v.4 no.4
• /
• pp.207-215
• /
• 2017

Hydraulic issues such as flow resistance, side wall correction, sediment, erosion and deposition, and channel design have close relation with distribution of bed shear stresses but the measurement of the distribution of bed shear stresses is not easy. In this study the Preston tube which makes possible relatively simple measurement of bed shear stresses is used to analyze the characteristics of bed shear distribution in compound open channels with different depth ratio. The Preston tubes are made and calibrated to develop the calibration formula and then they are applied to measure bed shear stress distribution in 5 cases depth ratio condition of compound channels. The results are compared with former experiment data, and characteristics of bed shear stress distributions are studied with different channel scales and Reynolds numbers. Although bed shear distributions with depth ratio show overall agreement with former studies, some differences are verified in bed shear variation, formation of inflection point in main channel, and distribution near floodplain junction which are due to high Reynolds number. Through the study applicability of the Preston tubes are also verified and characteristics of bed shear distribution in compound channels are suggested with Reynolds number and depth ratio.

• Journal of the Korean Geosynthetics Society
• /
• v.10 no.2
• /
• pp.1-12
• /
• 2011

In order to analyze the influence of particle bonding and crushing on the characteristics of shear behavior, especially residual shear behavior of granular soil, ring shear test was simulated by using DEM(Discrete Element Method)-based software program PFC(Particle Flow Code). Total four models including two non-crushing models and two crushing models were created in this study by using clump or cluster model built in PFC. The applicability of Lobo-crushing model proposed by Lobo-Guerrero and Vallejo(2005) was investigated. In addition, the results of ring shear test were analyzed and compared with those of direct shear test. The results showed that the modelling of ring shear test should be conducted to investigate the residual shear behavior. The Lobo-crushing model cannot be applied to investigate the residual shear strength. Finally, it can be concluded that the numerical models excluding Lobo-crushing model suggested in this study can be used extensively for other studies concerning the residual shear behavior of granular soil including soil crushing.

• Ecology and Resilient Infrastructure
• /
• v.5 no.4
• /
• pp.199-209
• /
• 2018

In river design, consideration of bed shear stresses is necessary to secure stability of levee and floodplain. In this study distributions of bed shear stresses in compound open channels are analyzed through numerical simulation for various width and depth. LES solver in OpenFOAM is applied to 12 cases of compound channel shapes considering secondary flow which effects distributions of bed shear stresses. By the results time averaged velocity distributions, secondary currents, and distributions of bed shear stresses are analyzed. Overall distributions of bed shears in floodplain show that higher shear stresses are seen in left of floodplain and the shears decrease toward right of floodplain. However, high local variations in shear stresses are shown due to the secondary flow effects. In shallow floodplain, bed shear stresses show low value below 0.8 times of averaged bed shear. In deep floodplain, bed shear stresses show high value over 1.2 - 1.4 times of averaged bed shear.