• Journal of the Microelectronics and Packaging Society
• /
• v.26 no.2
• /
• pp.15-21
• /
• 2019

We investigated the structural, electrical and optical properties of zinc oxide (ZnO) ultra-thin films grown at $150^{\circ}C$ by atomic layer deposition (ALD). Diethylzinc and deionized water were used as metal precursors and reactants, respectively, for the deposition of ZnO thin films. The growth rate per ALD cycle was a constant 0.21 nm/cycle at $150^{\circ}C$, and samples below 50 cycles had amorphous properties due to the relatively thin thickness at the initial ALD growth stage. With the increase of the thickness from 100 cycles to 200 cycles, the crystallinity of ZnO thin films was increased and hexagonal wurtzite structure was observed. In addition, the particle size of the ZnO thin film increased with increasing number of ALD cycles. Electrical properties analysis showed that the resistivity value decreased with the increase of the thin film thickness, which is correlated with the decrease of the grain boundary concentration in the thicker ZnO thin film due to the increase of grain size and the improvement of the crystallinity. Optical characterization results showed that the band edge absorption in the near ultraviolet region (300 nm~400 nm) was increased and shifted. This phenomenon is due to the increase of the carrier concentration with the increase of the ZnO thin film thickness. This result agrees well with the decrease of the resistivity with the increase of the thin film thickness. Consequently, as the thickness of the thin film increases, the stress on the film surface is relaxed, the band gap decreases, and the crystallinity and conductivity are improved.

• Journal of the Korean Electrochemical Society
• /
• v.4 no.3
• /
• pp.113-117
• /
• 2001

Specific capacitance and charge-discharge rate of EDLC using activated carbon electrode were affected by the compositions of electrolytes, the conditions of charge-discharge and physical properties of activated carbon materials. The activated carbon electrode was prepared by dip coating method. Charge-discharge test and electrochemical experiments were carried out for various kinds of organic electrolytes. Effects of charge and discharge current density on the specific capacitance were studied. Characteristics of leakage current, self-discharge and time-voltage curves in optimum conditions of organic electrolytes were compared with conventional $1M-Et_4NBF_4/PC$ electrolyte. The EDLC using MSP-20(specific surface area: $2000m^2/g$) electrode and $1M-LiPF_6/PC-DEC(1:1)$ was exhibited th highest specific capacitance of 130F/g and low polarization resistances. The EDLC using MSP-20 electrode at $1M-LiPF_6/PC-DEC(1:1)$ was small leak current of 0.0004A for 15min, long voltage retention of 0.8V after 100h and linear time-voltage curves with small IR-drop.

• Journal of the Korean Electrochemical Society
• /
• v.8 no.1
• /
• pp.32-36
• /
• 2005

[ $WO_3$ ] and $NiO-WO_3$ thin films were deposited on a Si (100) substrate by using high vacuum thermal evaporation. The effects of various film thicknesses on the surface morphology $WO_3$ and $NiO-WO_3$ thin films were investigated. X-ray diffraction (XRD), Scanning electron microscopy (SEM) and X-ray photoelectron spectroscopy(XPS) were employed to characterize the deposited films. The results suggest that as $WO_3$ thin films became thick, their grain grew up to a $0.6{\mu}m$. On the other hand, NiO-doping to $WO_3$ thin films inhibited the grain growth five times less than undoped $WO_3$ thin films. This results show that NiO doping inhibited the grain growing of $WO_3$ thin films. Also, the variation of NOx sensitivity $(R_{NOx}/R_{air})$ to the thickness of $WO_3$ and $NiO-WO_3$ thin films were measured according to the thickness change of thin films and the working temperature of sensor in 5ppm NOx gas. As a result, $NiO-WO_3$ thin films showed more excellent properties than $WO_3$ thin films for NOx sensitivity.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.47 no.2
• /
• pp.15-20
• /
• 2010

In this study, AZO (Al: 3 wt%) thin films have been prepared on PES Plastic substrates at various working pressure (5~20 mTorr), $O_2$ gas flow rate(0~3%) and the fixed substrate temperature of 200 f by using the RF magnetron sputtering and their optical and electrical properties have been studied. The XRD measurement shows that AZO thin films exhibit c-axis preferred orientation. From the results of AFM measurements, it is known that the lowest surface roughness (3.49 nm) is obtained for the AZO thin film fabricated at 5 mTorr of working pressure and 3% of $O_2$ gas flow rate. The optical transmittance of AZO thin films is measured as 80% in the visible region. We observe that the energy band gap of AZO thin films increases with decreasing the working pressure and the $O_2$ gas flow rate. This phenomenon is due to the Burstein-Moss effect. Hall measurement shows that the maximum carrier concentration ($2.63\;{\times}\;10^{20}\;cm^{-3}$) and the minimum resistivity ($4.35\;{\times}\;10^{-3}\;{\Omega}cm$) are obtained for the AZO thin film fabricated at 5mTorr of working pressure and 0% of $O_2$ gas flow rate.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.21 no.4
• /
• pp.575-581
• /
• 2020

A colorless antistatic agent was prepared for use in antistatic films for liquid crystal displays (LCDs) requiring low surface resistance and high transmittance. Among various lithium-fluoro compounds and quaternary ammonium salts, antistatic materials were selected based on their electrical conductivity, and antistatic agents were prepared to measure the surface resistance. As a result, the material with high conductivity showed a relatively low surface resistance, i.e., relatively good antistatic performance. Based on the antistatic materials selected, the formulation ratio for producing the best antistatic agent was established through the experimental design method and the effects of each factor were analyzed. The higher the use of lithium- fluoro compounds as antistatic materials, the higher the ratio of oligomer use with multi-functional groups, and the smaller the surface resistance. The quaternary ammonium salts increased the antistatic performance of the lithium-fluoro compounds, but the effects of the amount used were not relatively large. After manufacturing the antistatic PET film, the properties of the antistatic film showed low surface resistance values (<10⁹ Ω/sq.), high permeability (>92%), low haze (<0.5%), and high whiteness (L^⁎>95). In addition, the antistatic film reliability was found to be excellent by showing a stable surface-resistance change rate of less than 10%, even under high temperature and high humidity conditions.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.24 no.2
• /
• pp.68-77
• /
• 2020

The purpose of the paper is to evaluate the pore structure and mechanical properties of early frost damaged concrete using electric arc furnace slag as aggregate. From the results, when the concrete is exposed to frost damage at an early age, the peak point of pores 100 to 150 ㎛ in diameter were transferred into larger one. When the freezing duration is not exceeded 24 hours, it is possible that the pore distribution of under the 200 ㎛ is maintained and pore size of over 500 ㎛ is not formed, and, the freezing resistance of concrete using EFG could be improved. When BFS was mixed in concrete using EFG as coarse aggregate, the relative strength is higher than that of natural coarse aggregate. Meanwhile, the elastic modulus and resonance frequency did not change significantly due to the early frost damage as compared with the compressive strength. So, it is necessary to analyze the correlation between the experimental results in order to evaluate the performance degradation due to early frost damage.

• Journal of the Korean Electrochemical Society
• /
• v.3 no.3
• /
• pp.157-161
• /
• 2000

In order to investigate the substrate effect on the electrochemical properties of thin-film electrode, $LiCoO_2$ was deposited onto the alumina, chemically etched-Si and flat-Si substrates. After annealing at $800^{\circ}C$ in $O_2$ for 30min, the film deposited on the alumina consisted of large particles with several cracks, whereas the film deposited on the flat-Si substrate was composed of very small and uniform particles. The films deposited on the flat-Si showed improved electrochemical properties such as peak potential divergence and rate-capability, over those deposited on the alumina and chemically etched-Si substrate, which can be attributed to the differences of the particle size surface morphology, and the electrical resistance of the current collector.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.22 no.1
• /
• pp.40-49
• /
• 2008

Interior permanent magnet synchronous motor(IPMSM) has become a popular choice in electric vehicle applications and so of due to their excellent power to weight ratio. To obtain maximum efficiency in these applications, this paper proposes the neural network control method. The controllable electrical loss which consists of the copper loss and the iron loss can be minimized by the error back propagation algorithm(EBPA) of neural network. The minimization of loss is possible to realize eHciency optimization control for the IPMSM drive. This paper proposes high performance and robust control through a real time calculation of parameter variation such as variation of back emf constant, armature resistance and d-axis inductance about the motor operation. Proposed algorithm is applied IPMSM drive system, prove validity through analysis operating characteristics con011ed by efficiency optimization control.

• Journal of Korean Society of Environmental Engineers
• /
• v.27 no.1
• /
• pp.36-42
• /
• 2005

This study examined the feasibility of producing sulfuric acid and ammonia water from ammonium sulfate solution using two-compartment electrodialysis with a bipolar membrane (EDBM). Electrodialysis experiments were carried out with 20 wt% ammonium sulfate at different current densities and sulfuric acid concentrations in a concentrate compartment. The current efficiency increased with the current density from 25 to $100\;mA/cm^2$. Nevertheless, the efficiency was relatively low compared with that of general desalting electrodialysis, owing to the diffusion of sulfuric acid from the concentrate compartment to the diluate. The diffusion rate through the anion exchange membrane increased with the sulfuric acid concentration in the concentrate compartment, which decreased the current efficiency. Conversely, the electrical resistance decreased with increasing current density owing to the Joulian heat generated during water dissociation in the transition region of the bipolar membrane under a high electric field. From the experimental results, we concluded that operating at a higher current density is effective from the perspective of current efficiency and electrical resistance when producing sulfuric acid and ammonia water from ammonium sulfate using a two-compartment EDBM process. Further studies on the effects of increasing the sulfuric acid concentration on current efficiency are required to apply the EDBM process practically.

• Elastomers and Composites
• /
• v.39 no.3
• /
• pp.179-185
• /
• 2004

Frequency dependency or electrical property stabilization during vulcanization of modified NR/IR composite materials was studied using in-situ electrical property measuring technique. Volume resistivity(p) before and after vulcanization reaction of the sample was measured as the function or frequency in the range or 1Hz to 10kHz at reaction temperatures of 130, 140, 150, and $160^{\circ}C$, respectively. A double stabilization mode of frequency dependency was observed, in which a slow stabilization process of p to a value of ca. $1.0{\times}10^7\;{\Omega}-cm$ occurred after a drastic initial decrease from ca. $9.0{\times}10^7\;{\Omega}-cm$. In addition, notable temperature dependencies of p values were also observed before and after vulcanization reaction, that is, p values at 130 and $140^{\circ}C$ after vulcanization were observed as about 1/3 of those values before vulcanization. All the observed facts were considered as the results from the interaction between the electrode and the bulk sample materials, i.e., electronic charge-discharge, and from the structure change of samples including CB rearrangement by the vulcanization.