• KOREAN JOURNAL OF PACKAGING SCIENCE & TECHNOLOGY
• /
• v.29 no.1
• /
• pp.51-57
• /
• 2023

Because of the global pollution caused by plastic disposal, demand for eco-friendly transformation in the packaging industry is increased. As part of that, the utilization of polylactic acid (PLA) as a food packaging material is increased. However, it is necessary to improve the crystallinity of PLA by adding nucleating agents or to improve the modulus by adding fillers because of the excessive brittleness of the PLA matrix. Thus, the cellulose nanofiber (CNF) was fabricated and dried to obtain a powder form and applied to the CNF/PLA nanocomposite. The effect of CNF on the morphological, thermal, rheological, and dynamic mechanical properties of the composite was analyzed. We can confirm the impregnated CNF particle in the PLA matrix through the field emission scanning electron microscope (FE-SEM). Differential scanning calorimetry (DSC) analysis showed that the crystallinity of not annealed CNF/PLA nanocomposite was increased approximately 2 and 4 times in the 1st and 2nd cycle, respectively, with the shift to lower temperature of cold crystallization temperature (T_cc) in the 2nd cycle. Moreover, the crystallinity of annealed CNF/PLA nanocomposite increased by 13.4%, and shifted T_cc was confirmed.

• Composites Research
• /
• v.36 no.5
• /
• pp.349-354
• /
• 2023

Poly(3-hexylthiophene) (P3HT) is a conjugated polymer that is highly soluble in organic solvents and is readily available. However, its electrical properties as an active channel in electronic devices are not enough for practical applications, necessitating further improvement in the properties. In this study, we demonstrate that the blending of two P3HT polymers (i.e., regio-regular (RR) P3HT and regio-random (RRa) P3HT) with different regioregularities can significantly improve charge transport characteristics of the blend films. The morphological and electrical properties of the blend films were systematically investigated by varying the ratio between two P3HT polymers. Atomic force microscopy (AFM), X-ray diffraction (XRD), and UV-visible absorption spectroscopy (UV-vis) were employed to evaluate the morphological and optoelectronic properties of the blend films. The crystallinity of the blend films increased with increasing the content of RRa-P3HT to 20 wt% and gradually decreased as the content increased to 80%. Consistently, the highest charge carrier mobility was obtained from the blend films containing 20 wt% RRa-P3HT, which value was measured to be 0.029 cm²/V·s. The values gradually decreased to 0.0007 cm²/V·s with increasing the content of RRa-P3HT to 80 wt%.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.28 no.3
• /
• pp.47-58
• /
• 2024

This study were conduced experimentally to analyze the heat-generating performance, flexural strength, and microstructure of conductive mortar mixed with micro steel fiber and multi-wall carbon nanotube (MWCNT). In the conductive mortar heat-generating performance and flexural strength tests, the mixing concentration of MWCNT was selected as 0.0wt%, 0.5wt%, and 1.0wt% relative to the weight of cement, and micro steel fibers were mixed at 2.0vol% relative to the volume. The performance experiments were conducted with various applied voltages (DC 10V, 30V, 60V) and different electrode spacings (40 mm, 120 mm) as parameters, and the flexural strength was measured at the curing age of 28 days and compared and analyzed with the normal mortar. Furthermore, the surface shape and microstructure of conductive mortar were analyzed using a field emission scanning electron microscope (FE-SEM). The results showed that the heat-generating performance improved as the mixing concentration of MWCNT and the applied voltage increased, and it further improved as the electrode spacing became narrower. However, even if the mixing concentration of MWCNT was added up to 1.0 wt%, the heat-generating performance was not significantly improved. As a result of the flexural strength test, the average flexural strength of all specimens except the PM specimen and the MWCNT mixed specimens was 4.5 MPa or more, showing high flexural strength due to the incorporation of micro steel fibers. Through FE-SEM image analysis, Through FE-SEM image analysis, it was confirmed that a conductive network was formed between micro steel fibers and MWCNT particles in the cement matrix.

• Composites Research
• /
• v.37 no.3
• /
• pp.209-214
• /
• 2024

Graphene oxide (GO), known for its high stiffness, thermal conductivity, and electrical conductivity, is being utilized as a reinforcement in nanocomposite materials. This study evaluates the mechanical properties of epoxy nanocomposites incorporating GO and edge modified GO (E-GO), which has hydroxyl groups substituted only on its edges. GO/E-GO was uniformly dispersed in epoxy resin using ultrasonic dispersion, and mechanical properties were assessed through tensile testing. The results showed that the addition of nanoparticles increased both tensile strength and toughness. The tensile strength of the epoxy without nanoparticles was 74.4 MPa, while the highest tensile strength of 90.7 MPa was observed with 0.3 wt% E-GO. Additionally, the modulus increased from 2.55 GPa to 3.53 GPa with the addition of nanoparticles. Field emission scanning electron microscopy of the fracture surface revealed that the growth of cracks was impeded by the nanoparticles, preventing complete fracture and causing the cracks to split in multiple directions. E-GO, with surface treatment only on the edges, exhibited higher mechanical properties than GO due to its superior dispersion and surface treatment effects. These results highlight the importance of nanoparticle surface treatment in developing high-performance nanocomposite materials.

• Journal of the Korean Magnetics Society
• /
• v.19 no.5
• /
• pp.180-185
• /
• 2009

Fe$_3$O$_4$ particles, prepared by a sol-gel method, were examined for their structural characteristic, particle shapes and sizes, and their magnetic properties. Two different chemical compositions (using a mol rate Fe$^{2+}$/Fe$^{3+}$ = 1/2 and only Fe$^{2+}$) and 2-methoxyethanol were used for making proper solutions. And the solutions were refluxed and dry in a dry oven and the samples were fired at 200$\sim$600$^{\circ}C$ in the N$_2$ atmosphere. The formation of single-phased spinel ferrite powders was identified with the X-ray diffraction measurement as they were fired at above 250$^{\circ}C$. The result of scanning electron microscopy measurement showed the increase of annealing temperature yielded the particle size increased. The magnetic transition was observed using the Mossbaur spectroscopy measurement. As the ferrite, prepared with the chemical composition (Fe$^{2+}$/Fe$^{3+}$ = 1/2), was fired at 250$^{\circ}C$, 78% of the ferrite had a ferrimagnetic property and 22% of the ferrite was non-magnetic. In case of preparing the sample with only Fe$^{2+}$ and annealed at 200$^{\circ}C$, it had a single phased spinel structure but its particle size was too small to be ferrimagnetic. The annealing temperature above 250$^{\circ}C$ made powders a spinel structure regardless of the preparation method. They had a typical soft magnetic property and their saturation magnetization and coercivity became larger as the annealing temperature increased.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.17 no.5 s.108
• /
• pp.461-475
• /
• 2006

In this paper, it is described about the tri-band mobile antenna system design to provide broadband multimedia and direct broadcasting services using goo-stationary Koreasat 3, simultaneously operated in Ka/K/Ku band. The radiating part of the antenna system with a fan beam characteristic in the elevation plane is composed of the quasi-offset dual shaped reflector and the tri-band feeder. The tri-band feeder is also composed of the Ka/K dual band feeder with the protruding dielectric rod, the circular polarizer, the ortho-mode transducer and the circular-polarized Ku band feed array. Especially, the Ka/K dual band circular polarizer was realized firstly using the comb-type structure. For fast satellite-tracking on the movement, the Ku band feed array has the structure of the $2{\times}2$ active phased array which can make electrical beams. And, the circular-polarized characteristic in the feed array was improved by $90^{\circ}$ rotating arrangement of four radiating elements polarized circularly by a $90^{\circ}$ hybrid coupler, respectively. Four beam forming channels to make electrical beams at Ku band are divided into the main beam channel and the tracking beam channel in the output, and noise temperature characteristics of each channel were analyzed on the basis of the contributions of internal sub_units. From the fabricated antenna system, the output power at $P_{1dBc}$ of Ka_Tx channel was measured more than 34.1 dBm and the measured noise figures of K/Ku_Rx channels were less than 2.4 dB and 1.5 dB, respectively, over the operating band. The radiation patterns with co- and cross-polarization in the tri-band were measured using a near-field measurement in the anechoic chamber. Especially, Ku radiation patterns were measured after correcting each initial phase of active channels with partial radiation patterns obtained from the independent excitation of each channel. The antenna gains measured in Ka/K/Ku band of the antenna system were more than 39.6 dBi, 37.5 dBi, 29.6 dBi, respectively. And, the antenna system showed good system performances such as Ka_Tx EIRP more than 43.7 dBW and K/Ku_Rx G/T more than 13.2 dB/K and 7.12 dB/K, respectively.

• Journal of dental hygiene science
• /
• v.10 no.3
• /
• pp.177-183
• /
• 2010

This study was begun to search effect of contact angles of elastic rubber impression materials on the surface of working cast. Of elastic rubber impression materials with a Type III consistency, such as polysulfide, polyether and addition silicone, we selected one and then measured the contact angle after dripping a distilled water 3.3ml. Then, after pouring a dental anhydrite in three types of impression materials, we prepared a working cast and then examined its surface. Contact angle was measured using a full automatic contact angle measuring system (DM-700, KYOWA, Japan), and the surface of working cast was observed using a field emission scanning electron microscope (JSM-6700F, JEOL Ltd., JAPAN). The following results were obtained: 1) $Mean{\pm}SD$ (SD: standard deviation) of the initial contact angles were $91.3{\pm}20.5^{\circ}$ in the addition silicone materials, $90.0{\pm}2.2^{\circ}$ in the polyethers and $101.5{\pm}2.3^{\circ}$ in the polysulfides. These results indicate that mean values were similar but standard deviations of the three materials showed a great discrepancy. 2) As the time elapsed, addition silicone materials were found to have a contact angle decreased abruptly as compared with the remaining two types. That is, the initial contact angle was $91.3^{\circ}$ and it was abruptly decreased to $29.4^{\circ}$ after 25 seconds. 3) In the polyethers, the initial contact angle was $101.5^{\circ}$ and it was decreased to $90.7^{\circ}$ after 25 seconds. In the polysulfides, however, the initial contact angle was $90.0^{\circ}$ and it was $84.2^{\circ}$ after 25 seconds. This showed almost no changes in the initial contact angles. Moreover, its magnitude was greater than that seen in additional silicones. 4) There were significant differences in the contact angles between the three types of elastic rubber impression materials as the time elapsed (p<0.001). On an observation on the surface of working cast, addition silicone materials were found to have the most dense surface. This was followed by polysulfides and polyethers in a descending order.

• Journal of the Korean Vacuum Society
• /
• v.17 no.3
• /
• pp.195-198
• /
• 2008

In this paper, it was demonstrated that organic thin-film transistors (OTFTs) were fabricated with the organic passivation layer by vapor deposition polymerization (VDP) processing. In order to form polymeric film as a passivation layer, VDP process was also introduced instead of spin-coating process, where polymeric film was co-deposited by high-vacuum thermal evaporation from 6FDA and ODA followed by curing. In order to investigate by compared with different passivation layer, the other OTFTs is fabricated to passivation by Polyvinylalcohol using spincoating. We can see that two different ways of passivation layer affect electric characteristic of OTFTs. The initial electric characteristic of OTFTs before passivation such as field effect mobility, threshold voltage, and on-off current ratio are $0.24cm^2/Vs$, -3V, and $10^6$, respectively. Then after polyimide passivation layer, field effect mobility change from $0.24cm^2/Vs$ to $0.26cm^2/Vs$, threshold voltage from -3V to 1V and on-off current ratio from $10^6$ to $10^6$, respectively. In the case of polyvinylalcohol passivation, the initial electric characteristic of OTFTs before passivation such as field effect mobility, threshold voltage, and on-off current ratio are $0.13cm^2/Vs$, 0V, and $10^6$, respectively. Then after polyvinylalcohol passivation layer, field effect mobility changes from $0.13cm^2/Vs$ to $0.13cm^2/Vs$, threshold voltage from 0V to 2V, and on-off current ratio from $10^6$ to $10^5$, respectively.

• Journal of the Korean Geographical Society
• /
• v.31 no.2
• /
• pp.213-254
• /
• 1996

The Korean Geographical Society was founded in 1945, when Korea was liberated from the Japanese rule. And The Journal of the Korean Geography activated academic studies of geography by publishing research papers in it. Professor Kang, Dae-Hyun wrote the first two specialized papers of rural geography in 1966: " Flood Plain Settlements on the Han River" and "The Location and Form of the Dispersed Villages around Dae-Cwan-Ryung". The early studies of rural geography were not based on serious academic foundations, such as the adjustment of theoretical notions and a good grasp of subjects. After choosing subjects that came to hand without academic consideration. they simply enumerated generalized items of the results of the field work investigation such as the location the landscape and the process of formation of the settlements. In the 1970s and 1980s, however, rural settlement studies progressed remarkably in Korea. More than 80% of 318 dissertations, theses, or papers collected for this review were written in the late 1980s, and the subjects and methodology became diversified. As may be expected, recent studies are found very systematic and problem-solving in the various fields - contexual understanding spatial structure, the development of clan villages according to the socialization process, the effects of rural-out migration on the change of villages etc. Such a trend can be understood as a reaction to the circumstances under which, as the Western society already experienced, rural villages become washed out by the waves of industralization and urbanization and hardly continue to exist. In this paper, geographical studies of rural settlement which have been carried out in Korea last fifty years will be reviewed under the four headings on the studies related to a) farming villages; b) fishing villages; c) mountain villages: and d) special function villages. Studies of farming villages and related ones are very diverse. The results of the studies carried out last fifty years can be classified into sixteen subjects. Just as, in the West, studies of rural settlement have been mainly concerned with farming villages since rural geography came into being, so, in Korea, they have been centred on farming villages. It is a natural result considering the history of human life. Even in Korea, however the rural settlement is no more an isolated life space which keeps unique traditions of old life style, but it begins to form a dynamic life space connected to big cities by heavy traffic. Because the modern farming villages of Korea have an undetachable connection with the cities, special methodology to solve new problems has been posed in the studies of rural settlement. Many scholars have produced a lot of studies of farming villages, and three of them are prominent: Oh. Hong-Seok, Choi, Ki-Yeop, and Lee, Moon-Jong. Oh, Hong-Seok is a versatile and hard-working scholar who has published more papers than anyone else in the various fields of rural geography such as farming villages, fishing villages, mountain villages, and reclamation villages. And he has expanded his concerns to environment issues in recent years. Choi, Ki-Yeop has maintained that the prototype of Korean rural villages is clan villages continuing to write a series of good papers in which he pursues their regionalizion in the process of socialization. Lee, Moon-Jong divides the spatial organization of side settlement, sahachon (settlement near the temple), religion settlement, orchard settlement, settlement near the foreign military camp, displaced people's settlement. Chung Gam Lok settlement, etc. Though The Korean Geographical Society has half a century's history, academic activties in the field of rural settlement have been performed no more than thirty years. We cannot help saying that it is admirable that in such a rather short time we have five academical schools of the rural geography in Korea. geography in Korea.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.425-426
• /
• 2013

IIIN계 물질 기반의 광 반도체는 직접 천이형 넓은 밴드갭 구조를 갖고 있기 때문에 적외선부터 가시광선 및 자외선까지를 포함한 폭 넓은 발광파장 조절이 가능하여 조명 및 디스플레이 관련 차세대 광원으로 많은 관심을 받고 있다. 일반적인 청색 및 녹색 발광영역의 활성층으로는 InGaN/GaN 다중양자우물구조를 사용하고 있으나, 장파장의 녹색 발광을 얻기 위해서는 인듐의 함유량이 증가하여야 한다. 하지만, 인듐의 함유량이 증가함에 따라서 InGaN/GaN 다중양자우물 구조내에서 인듐의 편석현상의 발생이 용이하게 되어 계면 특성을 저하할 뿐 아니라, 비발광 센터를 증가하여 발광 효율을 급격히 감소시키는 원인이 되고 있다. 또한, InGaN과 GaN의 큰 성장온도의 차이에 따라 800도 부근의 저온 영역에서 성장된 InGaN층이 1,000도 이상의 고온 영역에서 GaN층이 성장시 InGaN층의 열화 현상이 급격히 발생되고 있다. 이를 억제하기 위해서 금속유기화학증착법의 성장 변수 최적화, 응력제어, 도핑 등의 편석 억제기술 및 보호층이 사용되고 있다. 본 연구에서는 인듐함유량이 증가된 녹색 InGaN/GaN 다중양자우물구조에서 InGaN 우물층 상하부에 도입된 GaN 보호층에 따라 발생되는 양자우물구조의 광학 및 결정학적 특성 분석을 통해 GaN 보호층의 역할을 분석하고자 한다. 본 연구에서는 금속유기화학증착장치를 이용하여 사파이어 기판위에 GaN 템플릿을 성장하고, n-형 GaN, InGaN/GaN 다중양자우물구조 및 p-형 층을 성장하였다. 앞선 언급하였듯이, InGaN/GaN 다중양자우물구조내에 GaN 보호층의 역할을 규명하기 위하여 샘플 A의 경우는 보호층이 전혀 없는 구조이고, 샘플 B의 경우는 InGaN 우물층의 상단부에만, 샘플 C의 경우에는 우물층 상부 및 하단부 모두에 약 2.0 nm 두께의 GaN 보호층을 형성하였다. 이 보호층의 유무에 따른 다중양자우물구조의 계면 특성을 확인하기 위한 X-선 회절을 이용하였고, 광학적 특성을 확인하고 상온 포토루미네선스법을 이용하여 녹색 발광 파장의 변화 및 발광세기를 관찰하였다. 우선적으로, 상온 포토루미네선스법을 이용하여 각 샘플의 발광특성을 확인한 바 상하부 모두에 GaN 보호층이 존재하는 샘플 C의 경우 약 510 nm 부근에서 발광이 관찰되었지만, 상단부에 GaN 보호층이 존재하는 샘플 B는 약 495 nm영역에 발광이 확인되었다. 특히, 전혀 보호층이 존재하지 않는 샘플 A의 경우 약 440 nm에서 발광하는 현상을 관찰하였다. 이는 우물층 상단부 및 하단부에 존재하는 GaN 보호층이 In의 확산을 억제하는 것으로 판단된다. 또한, 발광파장 및 세기를 확인한 바, 보호층의 존재하지 않을수록 단파장화가 발생함에도 불구하고 발광세기는 급격히 약해지는 것으로 보아 계면특성이 저하되어 비발광센터가 증가되는 것으로 판단된다. 이를 구조적으로 확인하기 위하여 X-선 회절법을 통한 ${\omega}$/$2{\Theta}$ 스캔의 결과는 In의 0차 피크가 GaN 보호층이 없을 경우 GaN의 피크 방향으로 이동하는 것으로 보아 GaN 보호층은 우물층 성장 후 GaN 장벽층을 성장하기 위해 온도를 증가시키는 과정에서 In의 확산되는 것으로 판단된다. 또한, 하부 GaN 보호층의 경우 GaN 장벽층 성장 후 온도를 감소시키는 과정에서 성장되므로, 우물층으로부터 In의 탈착현상이 아닌 장벽층과의 상호 확산으로 판단된다. 또한, 계면특성을 확인하기 위해 InGaN의 X-선 위성 피크를 확인한 바 샘플 A의 경우 매우 넓고 약한 피크가 관찰된 반면, 보호층이 존재하는 샘플 B와 C의 경우 강하고 얇은 피크가 확인되었다. 이는 GaN 보호층의 도입으로 인해 계면특성이 향상되는 것으로 판단된다. 따라서, 우리는 InGaN/GaN 다중양자우물구조에서 GaN 보호층은 상부의 열화 억제 뿐아니라, 하부의 장벽층 및 우물층 사이의 상호확산을 억제하는 GaN 보호층의 도입을 통하여 우수한 계면 특성 및 비발광센터의 억제를 얻을 수 있을 것으로 생각되며, 이는 향후 GaN계 발광다이오드의 전계 발광특성을 증가하여 우수한 발광소자를 개발할 수 있을 것으로 기대된다.