• Journal of the Korean Chemical Society
• /
• v.13 no.1
• /
• pp.16-24
• /
• 1969

Ni, Co, Zn, Cd, Mn, Mg, Ca, Sr, Ba 등의2가 금속과 U(VI) 및 V(IV)의 이온이 만드는 $MCup_2$ 조성의 cupferrates 착화합물에 관하여, 그 용해도가 좋은 dioxane-$H_2O$, methanol-$H_2O$, ethanol-$H_2O$ 및 2-propanol-$H_2O$의 혼합용매를 사용하여, 그들의 몰분율을 변화시키면서 제 1, 제 2 및 전체의 열역학적인 안정도상수를 전위차적정법에 의하여 측정하고, 안정도 상수와 유기용매의 몰분율에 관한 실험식을 얻었다. 한편 분광광전법에 의하여 가능한 cupferrates의 전체 안정도 상수를 측적하여 이들과 비교하였다. 2가 금속 cupferrates의 안정도상수는 위에 적은 금속의 순서로 감소하고, 이들의 log $K_1$은 log $K_2$보다 크지만, U(VI)과 V(IV)의 cupferrates는 log $K_1$$K_2$여서 1:1과 1:2 착화합물 사이에 구조 변화가 있는듯하다. 몰분율이 영인 점에서의 안정도상수는 금속 cupferrates의 수용액에서의 용해반응의 평형상수에 해당하며, 금속의 착화합물의 안정도상수와 용해도와는 무관하고, K<$10^5$인 cupferrates에 관해서는 분광전법을 적용하기 어렵다.

• Korean Journal of Materials Research
• /
• v.18 no.4
• /
• pp.193-198
• /
• 2008

$WO_3$-doped $SnO_2$ thin films were prepared in a solution-deposition method and their gas-sensing characteristics were investigated. The doping of $WO_3$ to $SnO_2$ increased the response ($R_a/R_g,\;R_a$: resistance in air, $R_g$: resistance in gas) to $H_2$ substantially. Moreover, the $R_a/R_g$ value of 10 ppm CO increased to 5.65, whereas that of $NO_2$ did not change by a significant amount. The enhanced response to $H_2$ and the selective detection of CO in the presence of $NO_2$ were explained in relation to the change in the surface reaction by the addition of $WO_3$. The $WO_3$-doped $SnO_2$ sensor can be used with the application of a $H_2$ sensor for vehicles that utilize fuel cells and as an air quality sensor to detect CO-containing exhaust gases emitted from gasoline engines.

• Journal of the Korean Wood Science and Technology
• /
• v.28 no.3
• /
• pp.25-33
• /
• 2000

This study was carried out to find the optimal isolation conditions of xylan from steam-exploded materials, such as rice straw(Oryza sativa), barley straw(Hordeum vulgare) and oak wood(Quercus mongolica), In the chemical composition, we found that the contents of water-extractives and ash of rice straw and barley straw were more than those of oak wood. Rice straw, barley straw and oak wood were steam-exploded at 20kgf/$cm^2$ for 3 minutes or 6 minutes. The content of lignin in three different steam-exploded materials was higher than that of non-treated materials. The crude xylan was extracted with hot water and 0.5% KOH solution from steam-exploded materials. In the sugar type of crude xylan extracted with hot water and 0.5% KOH solution, the oligomer content of crude xylan extracted with hot water was much more than that of crude xylan extracted with 0.5% KOH solution. The crude xylan was purified with 5% barium hydroxide Solution and ethanol precipitation procedure. The content of xylose of purified xylan was over 85%, but other sugar residues(arabinose, mannose, galactose and glucose) were not removed completely.

• Journal of the Korean Ceramic Society
• /
• v.38 no.12
• /
• pp.1097-1103
• /
• 2001

TiO$_2$anchored on a porous clay ceramic support (PCS) for use in lightweight photocatalyst were synthesized by the dropping precipitant method. A PCS of macro and micro pore size of around several mm~${\mu}{\textrm}{m}$ in diameter were prepared by the rapid heat treatment at, 1,15$0^{\circ}C$ for 10 min from low grade of clay. The change in pH of reaction solution due to the different addition rate of NH$_4$HCO$_3$as a precipitant, the reaction temperature and the concentration of TiCl$_4$had a pronounced effect on the nature of precipitated TiO$_2$particles on the surface of a PCS and the crystal structure of precipitated TiO$_2$particles. At an addition rate of 0.8 ml/min of NH$_4$HCO$_3$and pH=6 of reaction solution, homogeneous precipitation of TiO$_2$particles on a PCS was achieved. TiO$_2$particles with anatase phase was precipitated on the surface of a PCS at the low concentration of TiCl$_4$, the high addition rate of NH$_4$HCO$_3$and the high reaction temperature.

• Journal of Navigation and Port Research
• /
• v.35 no.8
• /
• pp.657-665
• /
• 2011

This study deals with an integrated problem for deciding sequencing and storage location of export containers together at its receiving operation in the container terminal with a perpendicular layout. The preferred storage location of an export container varies with the priority of the corresponding loading operation and the waiting time of an external truck depends on its storage time. This paper proposes the mixed integer programming model considering the expected arrival time and expected finish time of an external truck and the preferred storage location for its loading operation. And we suggest the heuristic algorithm based on a simulated annealing algorithm for real world adaption. We compare the heuristic algorithm with the optimum model in terms of the computation times and total cost and the performance of the heuristic algorithm is analyzed through a numerical experiment.

• Journal of the Korean Chemical Society
• /
• v.39 no.1
• /
• pp.40-46
• /
• 1995

A new analytical luminescence method for the Tb+3 and Eu+3 ions was studied using the fluorescence enhancement of the ions on the TLC plate. Compared to the specific emission intensities of the ions in aqueous or ethanol solution, if spotted on the TLC plate, the line intensities were extremely enhanced. There was additional enhancement effect of the lines from the ions on the TLC plate, if treated with ο-phenanthroline. Based on the luminescence enhancement, the detection limit of the ions was lowered more than 6 order of magnitude compared to the luminescence method using solution samples. The energy-transfer mechanism was also explained for the theoretical back ground of the luminescence enhancement.

• Journal of Korean Society of Forest Science
• /
• v.35 no.1
• /
• pp.24-32
• /
• 1977

According to the chlorous salt method, most of holocellulose whose lignin was removed, was obtained. In extracting xylan from holocellulose by the different densities of alkali, 5% KOH was extracted three times but still there remained part of xylan in it and another composite of hemicellulose and cellulose was obtained. The extraction of 10% and 20% KOH showed a desirable result. Rather than the ordinary method to use a large quantity of ethanol in the precipitation isolation of xylan, the method to use a small quantity of ethanol in adopting the dialysis with cellophane-membrane by condensing density to one tenth, made il possible to extract a high purity xylan in a high retrieving rate. In isolating glucomannan, the residue of 5% KOH extraction contained a large quantity of xylan, the residue of 10% and 24% KOH extraction, also showed the same result and the comparison between glucose and mannose was approximately 1 : 1. The purification of Fehling solution made it possible to obtain comparatively pure xylan but the process of oxidation dissolution was complicated and the retrieving rate was low. This was not a good method. The ethanol titration purified a high purity xylan in a high retrieving rate and was a very excellent purifying method, considering its simple and easy process. These two purifying methods, however, could not completely remove the residue of arabinose. This will be examined and reported later.

• KSBB Journal
• /
• v.15 no.4
• /
• pp.352-358
• /
• 2000

Preparation for the simplified separation of chitosandoligosaccharides from enzymatic hydrolysate was investigated. Two different types of chitosan beads as substrate were prepared as organic-based bead by W/O emulsion method and water-based bead by alkaline treatement. The average size of organic-based bead was $200{\mu}m$, and that of water based beads were $4000{\mu}m$, $100{\mu}m$, $30{\mu}m$, in diameter respectively. Enzyme stability was maintained over 80% at PH 6 after 24 hours. The optimal condition for the production of chitosanoligosaccharides was at pH 6.0, $50^{\circ}C$ and 40U (200U/g-chitosan) According to final oligosaccharide concentration water-based bed showed the similar result with that of organic-based bead even through it had smaller surface area attacked by chitosanse than that of organic-based bead. It is probable that the structure of water-based chitosan bead was looser than that of organic-based bead so enzyme penetrated easily into the bead structure. For the oligosaccharide production versus surface area the different size of water-based beads was investigated, Maxiaml production yield was observed in the $30{\mu}m$ beads. Consequently the water-based chitosan bead was better than the organic-based bead in this reaction system.

• Journal of the Korean Ceramic Society
• /
• v.40 no.6
• /
• pp.577-582
• /
• 2003

BaTiO$_3$ fine powders were synthesized by hydrothermal process from peroxo-coprecipitate precursors. The peroxo-coprecipitates were obtained by addition of the BaCl$_2$, TiCl$_4$, and $H_2O$$_2$ aqueous solution to an ammonium solution. Hydrothermal reaction was conducted at various reaction temperatures, times and pH ranges. Unlike the conventional hydrothermal synthesis which needs highly alkaline condition over pH 13 with KOH or NaOH, the present method offered well-developed crystalline (perovskite) BaTiO$_3$ powders synthesized below pH 12 with use of ammonium solution. It was found that the phase-pure fine powders were formed at temperatures as low as 11$0^{\circ}C$ and the properties of the powders synthesized over 13$0^{\circ}C$ were almost same regardless of the reaction time. BET surface area of the prepared powder was as high as 76 $m^2$/g and the calculated particle (particulate) size was below 20 nm. The ultrafine particulates formed weak agglomerates. The microstructure and dielectric properties of BaTiO$_3$ ceramics sintered at the temperature range of 1150~125$0^{\circ}C$ were evaluated.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.232-232
• /
• 1999

교류형 플라즈마 방전 표시기(AC Plasma Display Panel, AC PDP)에 사용되는 플라즈마는 그 부피가 너무 작아서 플라즈마에 변화를 일으키지 않고 그 물성을 관측하기란 쉬운일이 아니다. 그래서 주로 PDP 내의 물성을 관측하는 데 시뮬레이션에 의존하게 된다. 그 물성중에 PDP내의 전계 분포에 대한 정보는 방전의 형성 및 소멸에 대한 많은 단서를 제공하고 있다. 특히 AC PDP의 경우, 유전체에 형성되는 벽적하(wall charge)가 방전의 형성 및 PDP 구동에 중요한 역할을 하는데, 이는 PDP 내의 전계 분포를 살펴봄으로써 대략 예측할 수 있다. 본 연구에서는 시뮬레이션에 의존하지 않고, 직접 레이저 유도 형광법을 이용하여 AC PDP 내의 전계를 측정하였다. 방전 가스인 헬륨(He)의 에너지 준위는 전계의 크기에 따라 에너지 준위가 변화하여, Rydberg(n$\geq$8) 준위가 여러 개의 준위로 나누어지는 현상이 일어나는데, 이를 Stack 효과라고 한다. 따라서 전계의 세기가 커짐에 따라서 각 준위와 준위 사이 값(splitting)이 커지는데, 이를 이용하면 전계를 측정할 수 있다. 즉, 헬륨 원자를 여기시키는 레이저 파장을 변화시키면서 관측되는 레이저 유도 형광 신호를 관측하면, 준위의 splitting을 관측할 수 있다. 본 연구에서는 PDP 내의 전계의 시간적 변화를 관측하였다. 50%, 40kHz의 구형파를 PDP의 두 전극에 가하였을 때, 플라즈마가 켜진 상태뿐만 아니라 플라즈마가 꺼진 후에도 전계에 의한 Splitting 신호가 관측이 되었는데, 전계로 환산하였을 때, 그 값은 대략 수 kV/cm의 값을 갖았는데, 이는 wall charge에 의한 값으로 사료된다.결과로 생각되어진다.플라즈마의 강도값을 입력하여 플라즈마의 radiation을 검출하고, 스퍼터링 공정중 실질적인 in-situ 정보로 이용하였다. PEM을 통하여 In/Sn의 플라즈마 강도변화를 조사하였다. 초기 In/Sn의 플라즈마 강도(intensity)는 강도를 100하여, 산소를 주입한 결과, plasma intensity가 35 줄어들었고, 이때 우수한 ITO 박막을 얻을 수 있었다. Pulsed DC power를 사용하여 아크 현상을 방지하였다. PET 상에 coating 된 ITO 박막의 표면저항과 광투과도는 4-point prove와 spectrophotometer를 이용하여 분석하였고, AES로 박막의 두께에 따른 성분비를 확인하였다. ITO 박막의 광투과도는 산소의 유량과 sputter 된 In/Sn ion의 plasma emission peak에 따라 72%-92%까지 변화하였으며, 저항은 37$\Omega$/$\square$ 이상을 나타내었다. 박막의 Sn/In atomic ratio는 0.12, O/In의 비율은 In2O3의 화학양론적 비율인 1.5보다 작은 1.3을 나타내었다.로 보인다.하면 수평축과 수직축의 분산 장벽의 비에 따라 cluster의 두께비가 달라지는 성장을 볼 수 있었고, 한 축 방향으로의 팔 넓이는 fcc(100) 표면의 경우 동일한 Ed+Ep값에 대응하는 팔 넓이와 거의 동일한 결과가 나타나는 것을 볼 수 있다. 따라서 이러한 비대칭적인 모양을 가지는 성장의 경우도 cluster 밀도, cluster 모양, cluster의 양 축 방향 길이 비, 양 축 방향의 평균 팔 넓이로부터 각 축 방향의 분산 장벽을 얻어낼 수 있을 것으로 보인다. 기대할 수 있는 여러