• Journal of the Korean Wood Science and Technology
• /
• v.45 no.5
• /
• pp.559-571
• /
• 2017

This study was conducted to determine the adhesive performances of plywoods affected by layering direction and the amounts of thermoplastic films. The face and back layers of veneer were hardwood species (Mixed light hardwood) and core layer veneer was radiata pine (Pinus radiata D. Don). Thermoplastic film used as adhesive were polypropylene (PP) film and polyethylene (PE) film. Thermal analysis and tensile strength were investigated on each films. As a result, the melting temperature of PP and PE films were $163.4^{\circ}C$ and $109.7^{\circ}C$, respectively, and the crystallization temperature were $98.9^{\circ}C$ and $93.6^{\circ}C$, respectively. Tensile strength and elongation of each films appeared higher on the width direction than length direction. Considering the characteristics of the thermoplastic films, the test for the amount of film used was carried out by layering film to the target thickness on veneer. The effecting of layering direction of film on plywood manufacturing was conducted by laminating in the length and width directions of the film according to the grain direction of veneer. Tensile-shear strength of plywood in wet condition was satisfied with the quality standard (0.7 MPa) of KS F 3101 when the film was used over 0.05 mm of PP film and over 0.10 mm of PE film. Tensile-shear strength of plywood after cyclic boiling exceeded the KS standard when PP film was used 0.20 mm thickness. Furthermore, higher bonding strength was observed on a plywood made with width direction of film according to grain direction of veneer than that of length direction of film. Based on microscopic analysis of the surface and bonding line of plywood, interlocking between veneers by penetration of a thermoplastic film into inner and cracks were observed.

• Journal of the Korean Vacuum Society
• /
• v.5 no.3
• /
• pp.258-262
• /
• 1996

We have investigated the changes in magnetoresistive characteristics, interfacial roughness, and preferred orientation with the Fe buffer layer thickness, annealing temperature, and the stacking number of layers variation in Fe/[NiFe/Cu] multilayers by using the 3-gun d.c. magnetron sputtering method. Intensity of the (200) orientation was increased with the increment of the Fe-buffer layer thickness. We found a maximum magnetoresistance ration of 4.7%, when the buffer layer thickness was 70$\AA$, and the field sensitivity also showed a maximum value at the same thickness. We varied the stacking number of multilayers with fixing the Fe buffer layer thickness of 70$\AA$. When the stacking number was 40 layers, maximum MR ratio(5.3%) was observed. With the variation of annealing temperature no change in the MR ratio was found beyond $300^{\circ}C$. But decrement of MR ratio was observed above $300^{\circ}C$. This decrement of the MR ratio was responsible for the increment of paramagnetic mixed layer caused by the diffusion of Cu layer and the change of antiferromagnetic coupling.

• Journal of the Society of Naval Architects of Korea
• /
• v.36 no.1
• /
• pp.90-98
• /
• 1999

For the control of vibration and noise of metal structures having relatively low damping, viscoelastic materials are widely used and usually attached at metal structures with an additional constraining layer to secure them. The damping and elastic properties of structures having constrained viscoelastic material layers are dependent on not only temperature and frequency but also their thicknesses. Hence, optimal design of the thicknesses of viscoelastic and constraining layers for a certain base structure are very important to maximize their efficiency and to lighten their weight. In this study, the variation of loss factor of beams having a constrained viscoelastic layer according to the change of thickness has been carefully investigated. From these, optimal design method of the minimum thickness beam having a given loss factor is suggested and numerically verified for a real beam.

• Journal of the Korean Vacuum Society
• /
• v.11 no.3
• /
• pp.166-170
• /
• 2002

Artificial $BaTiO_3$(BTO)/$SrTiO_3$(STO) oxide superlattice have been deposited on MgO (100) single crystal substrate by pulsed laser deposition(PLD) method. The stacking periodicity of BTO/STO superlattice structure was varied from $BTO_{1\;unit\; cell}/STO_{1\;unit\; cell}$ to $BTO_{125\;unit\; cell}/STO_{125 \;unit \;cell}$ thickness with the total thickness of 100 nm. The result of X-ray diffraction showed the characteristics of superlattice in the BTO/STO multilayer structure. we have also confirmed that there was no interdiffusion at the interface between BTO and STO layers by high resolution transmission electron microscopy(HRTEM). The dielectric constant of superlattice increased with decreasing stacking periodicity of the BTO/STO superlattice within the critical thickness. The dielectric constant of the BTO/STO superlattice reached a maximum i.e., 1230 at a stacking perioicity of $BTO_{2\;unit\; cell}/STO_{2\;unit\; cell}$ .

• Journal of the Korean Society of Radiology
• /
• v.17 no.1
• /
• pp.107-114
• /
• 2023

X-ray fluorescence analysis has been widely used in the field of science and industry because it gives information about elements and their concentrations without destruction of samples. To increase analysis accuracy of fluorescence generated by photons of the transmission-type X-ray tube for mixture and compound samples would be recommend to have strong energy near 10 keV and 20 keV simultaneously. Tungsten of 9.65 keV and molybdenum of 17.48 keV were considered as targets with dual deposition structure for obtaining two strong characteristic X-rays, and the transmission-type X-ray tube was analyzed using Geant4 Monte Carlo simulation. The W-Mo structure resulted in strong characteristic X-ray near 10 keV and 20 keV simultaneously. A structure with Mo-W multilayers of 5 ㎛ thick also gave optimal spectrum. Various material combination and thickness optimization for the dual-structured target can give X-ray spectrum with strong characteristic X-ray of specific energies.

• Proceedings of the KIEE Conference
• /
• 2002.07b
• /
• pp.873-875
• /
• 2002

본 논문에서는 Magnetic Yoke를 이용, 자기저항을 최소화하여 관내의 자기장을 증가시키고, 또한 펌핑 압력을 증가시킨 Linear Pump를 설계하고 제작하였다. Magnetic Fluid Linear Pump는 직경 12mm인 관에 적용할 수 있도록 설계하였으며 Magnetic Yoke는 두께 0.5mm 규소강판을 적층하여 사용하였으며, Coil은 1000 Tum으로 하여 기자력을 발생시켰다. Pump의 동작 특성을 분석하기 위하여 제작된 Magnetic fluid Lineal Puup의 내부 자기장을 측정하였으며, 인가된 자기장에 의하여 형성되는 Magnetic Fiuld의 형상을 측정하였다.

• The Korean Journal of Rheology
• /
• v.7 no.1
• /
• pp.42-49
• /
• 1995

항공용 프리프레그의 기체 투과와 creep 변형 현상을 실험과 모델링을 통하여 autoclave 공정의 주요 공정변수인 시간, 온도 그리고 consolidation 압력에 대하여 연구하였 다. 적층된 프리프레그를 이용한 실험을 통하여 진공/autoclave 압력이 프리프레그에 가해졌 을 때 프리프레그의 두께는 선형 점탄성 변형을 나타내며 in-plane 기체 흐름은 투과 hysteresis 와 함께 non-Darcian flow 현상을 나타냄을 보여주었다. 이러한 현상은 bulk dimensional relaxation 그리고 미시적 기공의 구조 재배열이라는 두 가지 점탄성 완화현상 으로 관찰되고 분석되어졌다. Modified Standard Linear Solid (SLS) 점탄성 모델을 사용하 여 실험결과를 분석한 결과 creep relaxation 과 기체투과 속도를 대표하는 모델상수를 결정 할수 있었다.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.05a
• /
• pp.305-305
• /
• 2004

쾌속조형 기술은 3차원 CAD 데이터를 일정한 두께 간격으로 슬라이싱한 각 층을 다양한 방법으로 만들고, 이러한 층을 한층씩 적층하여 원하는 3차원 형상을 신속하게 제작하는 기술이다. 쾌속 조형법은 초기에는 광(beam)에 의해 형상이 만들어진다고 하여 광조형법이라고 불렸다. 그 후 시작품(Prototype)을 신속(Rapid)하게 제작할 수 있다는 사실로부터 'Rapid Prototyping' 또는 '쾌속 조형법' 이라고 불려지게 되었다.(중략)

• Journal of Korean Society of Steel Construction
• /
• v.10 no.3 s.36
• /
• pp.451-461
• /
• 1998

The solution of anisotropic plate via the classical methods is limited to relatively load and boundary conditions. If these conditions are more complex, the analysis becomes increasingly tedious and even impossible. For many plate problems of considerable practical interest, analytic solutions to the governing differential equations cannot be found. Among the numerical techniques presently available, the finite difference method and the finite element method are powerful numerical methods. The objective of this paper is to compare with each numerical methods for the buckling load and modes of anisotropic composite laminated plates considering shear deformation. In applying numerical methods to solve differential equations of anisotropic plates, this study uses the finite difference method and the finite element method. In determining the eigenvalue by Finite Difference Method, this paper represent good convergence compared with Finite Element Method. Several numerical examples and buckling modes show the effectiveness of various numerical methods and they will give a guides in deciding minimum buckling load and various mode shapes.

• Composites Research
• /
• v.30 no.5
• /
• pp.297-302
• /
• 2017

Finite element analysis of T-beam laminate structure under bending-torsional loading was conducted to prevent the delamination which is the major failure behavior on laminated composites. Three-dimensional preform, which is that fabric is braided through thickness direction, is suggested from the laminate analysis. The analysis aimed to optimize the fiber ratio in laminated composites. After it is suggested that guideline for design of T-beam structure using commercial software ANSYS Composites PrePost. The results show that strength of T-beam structure is increased 21.6% when the fiber density along with beam length direction is two times bigger than transverse direction. It is expected that development of high strength T-beam structure using designed three-dimensional preform.