• Journal of the Korean Chemical Society
• /
• v.34 no.6
• /
• pp.534-538
• /
• 1990

Chromium(Ⅵ) compound, [$C_9H_7$NH]$_2Cr_2O_7$ has been prepared by the reaction of isoquinoline with chromium trioxide under the presence of water. [$C_9H_7$NH]$_2Cr_2O_7$ is nonhydroscopic and dissolved in water very well. Structure of [$C_9H_7$NH]$_2Cr_2O_7$ is identified by FTIR spectra and elemental analysis data. The ability of [$C_9H_7$NH]$_2Cr_2O_7$ for the oxidation of alcohols were examined in methylene chloride. [$C_9H_7$NH]$_2Cr_2O_7$ was found as efficient oxidizing agent for the conversion of allyl, primary and secondary alcohols to the corresponding aldehydes or ketones.

• Journal of the Mineralogical Society of Korea
• /
• v.7 no.1
• /
• pp.14-24
• /
• 1994

The Sungsan clay deposits have been formed by the hydrothermal alteration of volcanic and volcanoclastic rocks of the Hwangsan Formation of Cretaceous age. Claystones are mainly composed of dickite, alunite, illitic minerals and tosudite. The mineralogical properties of clay minerals have been studied using X-ray diffraction analysis, electron microscopy, electron microprobe analysis, and infrared absorption analysis. The physicochemical condition for the clay deposits also have been studied by the activity diagrams and mineral assemblages. Dickite, the dominant mineral in clay deposits, occurs generally as massive aggregates. It shows book-structure of well-defined hexagonal plates. Chemistry of dickite agrees with its ideal formula. Peak depth ratios in infrared absorption spectra were used for discrimination between pure and mixture of kaolin minerals. Five hydrothermal alteration zones are divided according to the mineral assemblages. From center to margin, alunite, dickite, illite and albite zones are discernible. Quartz zone occurs as small lenticular form in dickite zone. The formation of dickite and illite zones are promoted by decreasing $a_{k^+}$. An increase in $a_{H_{2}SO_{4}}$ or $a_{K_{2}SO_{4}}$ is required for the formation of alunite zone. Estimated temperature of formation ranges 110-270 $^{\circ}C$

• Economic and Environmental Geology
• /
• v.46 no.6
• /
• pp.495-508
• /
• 2013

Recently, stable isotopes (${\delta}^{18}O$ and ${\delta}D$) of water are increasingly analyzed using laser-based technologies. These methods have advantages over Isotope Ratio Mass Spectrometry (IRMS) in that they can be used for in-situ measurements and require much less maintenance and preparation work. Two types of laser-based methods are currently available, which have different analytical principles; OA-ICOS (off-axis integrated cavity output spectroscopy) and WS-CRDS (wavelength-scanned cavity ring-down spectroscopy). In the WS-CRDS instrument, water is vaporized at controlled environment and transferred to an optical cavity by nitrogen carrier gas, and stable isotopic compositions of water vapor are measured using the degree of absorbance of specific wavelengths and the ratios of attenuation time of the laser intensity with the sensitivity of ppb to tens of ppt level. In this study, we introduce the principle of the WS-CRDS technology and the performance results including stability and comparisons with Isotope Ratio Mass Spectrometry (IRMS) and suggest possible applications of various topics in isotope hydrology.

• The Korean Journal of Food And Nutrition
• /
• v.10 no.1
• /
• pp.44-52
• /
• 1997

Nephrolithiasis is the most common disorder of the urinary tract in hospitalized patients, more frequently increased in 30~50 years of age, more common in males than in females, prior right stone to left side, and than upper ureteral stone is found in cultural country, while lower ureteral stone is increased in uncultural country. Stone components are classified as calcium oxalate, calcium phosphate, magnesium ammonium phosphate, uric acid, cystine, and their mixed stone, respectively. According to the pathophysiology of urinary stones, supersaturation/crystalization of inorganic salt concentration in urine, organic matrix, inhibitor deficiency, and epitaxy theory could be based on the stone formation. Not only hypercalciuria, hyperparathyroidism, hyperoxaluria, hyperuricosuria, and cystinuria, but also renal tubular acidosis, hypervitaminosis D, and peptic ulcer, are significantly associated with nephrolithiasis. In this study upper ureteral stone component were analyzed with chemical analysis, infrared spectrum, and image analyzer from K43 patient wit erosive gastritis. As the results, mixed stone of calcium oxalate dihydrate and calcium phosphate apatite was identified, the values of clinical test in blood and urine maintained normal revels. The relapsing urinary stone from K43 have no correlation between factors for stone formation reported early, also have no evidence for risk from erosive gastritis.

• Membrane Journal
• /
• v.15 no.1
• /
• pp.8-14
• /
• 2005

The hyaluronic acid (HA) with excellent biocompatibility can be combined with the monomer polylactide with good biodegradability to produce biocompatible materials which can control the period of degradation in a human body. By freeze drying method, HA and the lactic acid, monomer of polylactide, or lactide, the ester dimer of polylactide, were crosslinked with crosslinking agent, l-ethyl-3-(3-dimethyl aminopropyl) carbodiimide. The analysis of infrared spectroscopy showed that the ester linkage was formed and the analysis of nuclear magnetic resonance (NMR) spectroscopy showed that the ester linkage was due to the reaction of lactic acid and HA. The conversion (6∼32%) and degree of crosslinking (4∼19%) increased but the selectivity was almost constant at 62% as the mole ratio of LA to HA increased from 1 to 10 in the crosslinking reaction. The brittleness became more pronounced and the rate of degradation became faster with more addition of lactic acid resulting from the higher ratio of LA to HA, and the swelling ratio was in the range of 500 to 2000%.

• Journal of Sensor Science and Technology
• /
• v.6 no.1
• /
• pp.6-15
• /
• 1997

This paper presents the multi-objective optimal design of thermopile sensor having beam or membrane structure. The thermopile sensor is composed of $Si_{3}N_{4}/SiO_{2}$ dielectric membrane, Al-polysilicon thermocouples and $RuO_{2}$ thin film for black body. The sensing method is based on the Seebeck effect which is originated from the temperature difference of the two positions, black body and silicon rim. The objective functions of the presented design are sensitivity, detectivity and thermal time constant. The modelling of the sensor is proposed including the package. The multi-objective optimization technique is applied to the design of the sensor not only inspecting the modelling equation but also simulating mathematical programming method. Especially, fuzzy optimization technique is adapted to get the optimal solution which enables the designer to reach the more practical solution. The design constraint of the voltage output originated from the change of the environmental temperature is included for practical use.

• Polymer(Korea)
• /
• v.31 no.5
• /
• pp.393-398
• /
• 2007

We studied the mechanism of liquid crystal alignment on polyvinylfluorocinnamate (PVCN-F) films which were irradiated by UV using polarized fourier transform infrared (FT-IR) spectroscopy and ultraviolet/visible (UV/Vis) spectroscopy. UV irradiation of PVCN-F films caused decrease of vinylene -C=C- stretching peak area at $1638cm^{-1}$ and shift of conjugated C:0 stretching vibration at $1712cm^{-1}\;to\;1734cm^{-1}$ which is caused by nonconjugated C=O stretching nitration. To study the orientation direction of 5CB liquid crystal (LC) molecules in the liquid crystal cell with PUV irradiation, rubbing treatment or without any treatment on the PVCN-F alignment layer, we used polarized FT-IR dichroism technique. We successfully measured 5CB LC alignment directions, which are perpendicular to the irradiated PUV polarization direction and parallel to the rubbing direction in the liquid crystal cell without using dichroic dyes.

• Economic and Environmental Geology
• /
• v.49 no.5
• /
• pp.335-347
• /
• 2016

The mineralogical and geochemical characteristics of diverse carbonate rocks can be investigated by using VNIRSWIR(visible near infrared-short wavelength infrared) spectroscopic analysis as a rapid, nondestructive, and inexpensive tool. Comparing whole rock analysis to VNIR-SWIR spectroscopic analysis, the analytical method was investigated to estimate CaO contents, mud impurity, and whiteness of carbonate rocks involved in high-grade limestones in the field. We classify typical carbonate rocks in the upper Pungchon Formation in high-grade limestone mine area such as the Gangweon, Chungmu and Baegun mine in the Jeongseon area. The results show that powdered specimen has much higher reflectance than cutted specimen between the same sample. Whiteness is highly correlated with reflectance(0.99) for powdered specimen. The absorption of mineral mixtures shifts in position as a result of the mass ratio of calcite and dolomite in the Chungmu mine by changing to 75:25, 50:50, and 25:75. The absorption peak position in carbonate mixtures is highly correlated with CaO contents(0.98~0.99). Based on color system, the carbonate rocks are grouped into (milky) white, light grey, light brown, grey, and dark grey. The absorption peak position shifts from 2340 nm to 2320 nm as CaO contents decrease from 55.86 wt.% to 29.71 wt.%. We confirmed that absorption peak position shifts depending on the amount of Ca, which is bonded to $CO{_3}^{-2}$, Mg, and Fe contents replacing Ca. This result suggests that CaO contents in carbonate rocks can be considered to quantitative analysis in the field by spectroscopic analysis.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.57-58
• /
• 2011

III-V족 화합물 반도체의 일종인 InSb는 77 K에서 0.23 eV의 작은 밴드 갭을 가지며 높은 전하 이동도를 가지고 있기 때문에 대기권에서 전자파 흡수가 일어나지 않는 3~5 ${\mu}m$범위의 장파장 적외선 감지가 가능하여 중적외선 감지 소자로 이용되고 있다. 하지만 InSb는 밴드 갭이 매우 작기 때문에, 소자 제작시 누설전류에 의한 소자 특성의 저하가 문제시 되고 있다. 또한 다른 화합물 반도체에 비해 녹는점이 낮고, 휘발성이 강한 5족 원소인 Sb의 승화로 기판의 화학양론적 조성비(stoichiometry)가 변하기 쉬워, 계면특성 저하의 원인이 된다. 따라서 우수한 특성을 가지는 적외선 소자의 구현을 위해서, 저온에서 계면 특성이 우수한 고품질의 절연막 증착 연구가 필수적이다. 본 연구에서는 InSb 기판 위에 $SiO_2$, $Si_3N_4$의 절연막 형성시 증착온도의 변화에 따른 계면 트랩 밀도를 분석하였다. $SiO_2$, $Si_3N_4$ 절연막은 플라즈마 화학 기상 증착법(PECVD)을 이용하여 n형 InSb 기판 위에 증착하였으며, 증착온도를 $120^{\circ}C$부터 $240^{\circ}C$까지 변화시켰다. Metal oxide semiconductor(MOS) 구조 제작을 통하여, 커패시턴스-전압(C-V)분석을 진행하였으며, 절연막과 InSb 사이의 계면 트랩 밀도를 Terman method를 이용하여 계산하였다[1]. 또한, $SiO_2$와 $Si_3N_4$의 XPS 분석과 TOF-SIMS 분석을 통하여 계면 트랩 밀도의 원인을 밝혀 보았다. $120{\sim}240^{\circ}C$ 온도 범위에서 계면 트랩 밀도는 $Si_3N_4$의 경우 $2.4{\sim}4.9{\times}10^{12}cm^{-2}eV^{-1}$, $SiO_2$의 경우 $7.1{\sim}7.3{\times}10^{11}cm^{-2}eV^{-1}$ 값을 나타냈고, 두 절연막 모두 증착 온도가 증가할수록 계면 트랩 밀도가 증가하는 경향을 보였다. 그러나 모든 샘플에서 $Si_3N_4$의 경우, flat band voltage가 음의 전압으로 이동한 반면, $SiO_2$의 경우, 양의 전압으로 이동하는 것을 확인할 수 있었다. 계면 트랩 밀도 증가의 원인을 확인하기 위해서, oxide를 $120^{\circ}C$, $240^{\circ}C$에서 증착시킨 샘플을 XPS 분석을 통하여 깊이에 따른 성분분석을 하였고, 그 결과, $240^{\circ}C$에서 증착된 샘플에서 계면에서 $In_2O_3$와 $Sb_2O_3$ 피크의 증가를 확인하였다. 이는 계면에서 oxide양이 증가함을 의미하며, 이렇게 생성된 oxide는 계면 트랩으로 작용하므로, 계면 특성을 저하시키는 원인으로 작용함을 알 수 있었다. Nitride 절연막을 증착시킨 샘플은 TOF-SIMS 분석을 통해, 계면에서의 성분 분석을 하였고, 그 결과, $240^{\circ}C$에서 증착된 샘플에서 In-N, Sb-N, Si-N 결합의 감소를 확인하였다. 이렇게 분해된 결합들의 dangling 결합이 늘어 계면 트랩으로 작용하므로, 계면 특성을 저하시키는 원인으로 작용함을 알 수 있었다. 최종적으로, 소자특성을 확인 하기 위하여 계면 트랩 밀도가 가장 낮게 측정된 $200^{\circ}C$ 조건에서 $SiO_2$ 절연막을 증착하여 InSb 적외선 소자를 제작하였다. 전류-전압(I-V) 분석 결과 -0.1 V에서 16 nA의 누설 전류 값을 보였으며, $2.6{\times}10^3{\Omega}cm^2$의 RoA(zero bias resistance area)를 얻을 수 있었다. 절연막 증착조건의 최적화를 통하여, InSb 적외선 소자의 특성이 개선됨을 확인할 수 있었다.

• Journal of the Korean GEO-environmental Society
• /
• v.24 no.3
• /
• pp.5-14
• /
• 2023

The dry unit weight of the soil can be obtained by measuring the weight of the oven dried soil. According to the Korean Industrial Standards (KS F), oven dried soil at 110±5℃ continuously increases in weight when exposed to air. However, there is no regulation on the weight measurement time of oven dried soil, making it difficult to accurately measure the dry weight. In this study, a method to easily determine the dry weight was presented through the analysis of the weight singularity that appears during weight measurement. The weight singularity represents the smallest value among the measured weights, and is the weight at which the effect of moisture absorption in the air of the sample is minimized. In the course of the experiment, a container was selected using a statistical analysis method, and a photograph of the soil samples were presented using an optical microscope. In addition, the temperature of the weight singularity was measured using a non-contact infrared thermometer. As a result of analyzing the weight singularity of six types of soil, including Jumunjin sand, Naeseong stream sand, Yecheon weathered granite soil, Jeju sand, Sabkha sand, and Ulleung sand, the weight singularity of oven dried sample appeared between 8 and 27 seconds after weight measurement, and the temperature ranged from 103.4 to 108.13℃. The weight decrease rate of the singularity was 0.0066 to 0.0085% depending on the soil samples.