• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.13 no.7
• /
• pp.2949-2954
• /
• 2012

This study was to examine the correlation between the brain function of adult suffering from obesity and the level of their obesity based on brainwave measurements. Based on the result of Body Composition Analysis (BCA) examination, population of 651 overweight pupils was chosen from June 2011 to December of 2012 in S city, I hospital. These patients were measured by timeseries linear analysis for their brain function and observed via brainwave activities. The results have been thus far; first, as their BMI (Body Mass Index) and level of obesity (body fat percentage) were higher, degree of mental stress and resistant to stress marked lower. These results prove that by managing the stress resistant ability and attention ability, self-controlling ability, one can expect a positive effect on finding a methods to ease the obese-related problems.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.6
• /
• pp.2729-2734
• /
• 2011

In this paper, an active replica Low-dropout(LDO) regulator with DC voltage matching circuit is presented. In order to match the voltage between replica and output of regulator, DC voltage matching circuit is designed. The active replica low dropout regulator has higher Power Supply Rejection(PSR) than that of conventional regulator. The designed DC voltage matching circuit can reduce the drawback that may be occurred in replica regulator. And using fully active element in regulator can reduce the chip area and heat noise with resistor. As results of HSPICE simulation with 0.35um CMOS parameter, the designed active replica LDO regulator achieves Power Supply Rejection, -28@10Hz better than -17@10Hz of conventional replica regulator without DC matching circuit. And the output voltage is 3V.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.15 no.12
• /
• pp.6980-6985
• /
• 2014

A micro-conductive pattern was fabricated on an insulating substrate ($SiO_2$) surface using a laser direct writing method. In the LIFT process, when the laser beam irradiates a thin metal film, the photon energy is absorbed by the film and converted to thermal energy, and the thermal decomposition reaction produced by the resulting heat conduction forms a deposit on the substrate. The resistivity of the micro-electrodes deposited through LIFT process with and without polymer coating was measured. The results showed that the electric conductivity of the micro-pattern and micro-structure can be increased approximatly two times when the deposited micropattern is fabricated through a LIFT process with a polymer coating, compared to the case without a polymer coating.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 2011.05a
• /
• pp.48.2-48.2
• /
• 2011

열전재료는 열과 전기에너지의 상호 변환이 가능한 재료로 이를 이용한 응용제품의 개발이 크게 주목을 받고 있으며, 특히 $Bi_2Te_3$계 합금의 경우 상온에서 가장 우수한 성능지수를 가지는 재료로 많은 연구가 진행되고 있다. 그러나 기존의 $Bi_2Te_3$계 합금은 일방향응고법으로 제조되어 많은 시간과 비용을 필요로 하고, 특히 C축의 Van der Waals 결합으로 인해 기계적 강도가 약하다는 단점이 있었다. 최근 분말야금법을 이용하여 기계적강도를 높이고, 격자산란에 의한 열전도도의 감소로 성능지수를 높일수 있는 방법들이 제시되고 있다. 본 연구에서는 급속응고공정인 가스분무법을 이용하여 n-type의 $95%Bi_2Te_3-5%Bi_2Se_3$분말을 제조하였고, 이 재료의 경우 성형조건에 따라 조직이 쉽게 변하기 때문에 이를 제어하기 위해 단시간동안 고압으로 성형가능한 자기펄스압축성형법(Magnetic Pulsed Compaction)을 이용하여 성형체를 제조하였다. 제조된 성형체는 밀도를 증가시키고 결정립성장을 억제시킬수 있는 방전플라즈마소결법(Spark Plasma Sintering)을 이용하여 소결체로 제조되었으며, 각각의 공정이 열전성능에 미치는 영향을 고찰하였다. OM (Optical Microscope) 및 SEM (Scaning Electric Microscope)을 이용하여 미세구조를 관찰하였고 XRD (X-Ray Diffraction)를 이용하여 상의 변화를 분석하였으며, 상온에서 경도를 측정함으로서 공정조건에 따른 기계적강도를 비교하였다. Seebeck계수는 시편의 양단에 온도차를 주어 발생하는 기전압을 측정하여 계산하였고, 전기비저항은 4point probe방법으로 측정하였다. 전하이동도 및 전하농도는 Hall측정으로부터 구하였고 열전도도를 측정하여 종합적인 열전성능을 평가하였다.

• Korean Journal of Soil Science and Fertilizer
• /
• v.21 no.4
• /
• pp.380-385
• /
• 1988

The urease adsorption on zeolite and the various properties of adsorbed urease were investigated to find out the influence of zeolite on activity and properies of urease. Free urease in solution was adsorbed on zeolite untill the max. adsorption, and the amount of max. adsorption was 11.3mg urease/100mg zeolite at pH 7.0. It is apparent that free urease was adsorbed on the outer surface of zeolite by cation exchange reaction, and more than 70% of urease adsorption was adsorbed within 30 min. The activity of adsorbed urease was decreased by 89.6%, whereas Km value was increased to 34.4mM, which is higher than that of free urease. The optimum pH of adsorbed urease was widened 6.5 to 7.0, compared to that of free urease 7.0. The resistance of urease to protease became weaker by adsorption, however substrate specificity and thermal stability were not affected.

• Composites Research
• /
• v.26 no.5
• /
• pp.309-314
• /
• 2013

Highly ablation resistant carbon nanotube (CNT)-phenolic composites were fabricated by the addition of low concentrations of CNT nanofiller. Tensile and compressive properties as well as ablative resistance were significantly improved by the addition of only 0.1 and 0.3 wt% of uniformly dispersed CNTs. An oxygen-kerosene-flame torch and a field emission scanning electron microscope (FE-SEM) were used to evaluate the ablative properties and microstructures of these CNT-phenolic composites. Thermal gravimetric analysis (TGA) revealed that the ablation rate was lower for the 0.3 wt% CNT-phenolic composites than for neat phenolic or the composite with 0.1 wt% CNT. Ablative mechanisms for all three materials were investigated using this TGA in conjunction with microstructural studies using a FE-SEM. The microstructural studies revealed that CNT acted as an ablation resistant phase at high temperatures, and that the uniformity of dispersion of the CNT played an important role in this resistance to ablation.

• Journal of the Korea Society of Computer and Information
• /
• v.12 no.6
• /
• pp.279-286
• /
• 2007

The competitiveness of a corporate has always been an endeavor factor in the field of Business Management and with introduction of computer, various system; Decision Support System. Executive Information System. Management Information System has dramatically improved the competitiveness. According to the environmental change, organizational complexity. rapid information technology development. it is accelerated to introduce the Enterprise Resource Planning(ERP) System. ERP System is considered as an important tool for management innovation. Korean enterprises have been adopting ERP to reinforce competitive power and to realize global standardization in recent years. This study on the performance of ERP Systems is designed to take a look at the importance, outcome factors of information system, the quality measurement of the information system, and breaking the quality of the information system into system quality, information quality.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.23 no.2
• /
• pp.226-233
• /
• 1999

An experimental study has been performed on natural convection heat transfer with a rapid crust formation in the molten metal pool of a low Prandtl number fluid. Two types of steady state tests, a low and high geometric aspect ratio cases in the molten metal pool, were performed. The crust thickness by solidification was measured 88 a function of boundary surface temperatures. The experimental results on the relationship between the Nusselt number and Rayleigh number In the molten metal pool with a crust formation were compared with existing correlations. The experimental study has shown that the bottom surface temperature of the molten metal layer, in all experiments. is the major influential parameter in the crust formation, duo to the natural convection flow. The Nusselt number of the case without a crust formation in the molten metal pool is greater than that of the case with the crust formation at the same Rayleigh number. The present experimental results on the relationship between the Nusselt number and Rayleigh number In the molten metal pool match well with Globe and Dropkin's correlation. From the experimental results, a now correlation between the Nusslet number and Rayleigh number in the molten metal pool with the crust formation was developed as $Nu=0.0923(Ra)^{0.302}$ ($2{\times}10^4< Ra<2{\times}10^7$).

• Proceedings of the Korea Concrete Institute Conference
• /
• 2008.11a
• /
• pp.533-536
• /
• 2008

This study is the application of phosphate magnesia cement for solidification of soils. The object of the study is the application of the pavment of the farm roads. The new pavement method must be environmental, ecologic and durable. So, for solidification of farm road's soil, we use magnesia cement as quick setting, high strength materials. At magnesia phosphate cement, mixing ratio of mono ammonium phosphate and magnesia is 4:6 and w/b is 50 wt%, it show 14 MPa of compressive strength, and high hydration heat. Solidified soils that mixing ratios of magnesia cement and soil are 4:6 and 5:5 have very high durability for freezing and thawing.

• Journal of Hydrogen and New Energy
• /
• v.10 no.4
• /
• pp.191-196
• /
• 1999

4-probe resistivity measurement technique was used to study hydrogen A-D(Absorption-Desorption)kinetics on Pd films(18 to 67nm thick) from 25 to $50^{\circ}C$, from 0 to 5 torr hydrogen pressure. Pd films were made on sapphire substrate by thermal evaporation technique under high vacuum at room temperature. Upto about 100 hydrogen A-D cyclings, no pulverization was observed, but film was detached partially from substrate. Forward reaction and backward reaction rate were analyzed separately. The activation energies of hydrogen A-D processes were obtained from the Arrhenius plot of the reaction rates. The activation energies of Pd films are not strongly dependent on the thickness of the film. But the activation energy of very thin film( l8nm thick) was smaller than the others.