• Proceedings of the KIEE Conference
• /
• 2008.07a
• /
• pp.2239-2240
• /
• 2008

고장전류를 억제하는 방법 중 우리나라에 가장 적합하고 효율적인 저항형 초전도 한류기의 성능을 결정짓는 중요한 요소인 퀜치 및 회복특성을 분석하였다. 실험장치를 구성하여 모의 사고를 발생시켰다. 모의 사고시 사고주기와 부하저항 값에 따라서, 초전도 한류기의 ��치 발생시간과 회복시간에 대해 분석하였다. 본 연구를 통하여 사고주기가 짧아질수록 회복시간과 퀜치 발생시간이 빨라진다는 사실과 부하저항이 클수록 퀜치 발생시간이 늦어지는 반면에 회복시간은 빨라진다는 두 가지 사실을 알 수가 있었다.

• Proceedings of the KIEE Conference
• /
• 2005.04a
• /
• pp.93-95
• /
• 2005

케이블 변압기용 케이블에는 반도전층이 설치되며 권선의 각 턴에 대하여 외측 반도전층을 접지함으로써 권선에 과다 전계가 인가되는 것을 억제하는 역할을 한다. 케이블 변압기는 케이블의 반도전층의 저항률에 따라 전계분포 및 전력손실이 다른 특성을 나타낸다. 반도전층의 저항률이 매우 높을 경우 각 턴에 인가되는 전계에 의해 각 턴의 접지 사이에 높은 전계가 인가되고, 저항률이 매우 낮을 경우 반도전층에서 높은 전력 손실을 야기하여 변압기의 전체 효율을 감소시키게 된다. 따라서 반도전층의 저항률을 적절히 선정함으로써 전체 변압기의 절연특성과 효율을 최적화 할 필요가 있다. 본 연구에서는 유한요소법과 진화전략을 적용하여 케이블 변압기용 케이블의 반도전층 최적화를 수행한다.

• Plant Journal
• /
• v.8 no.4
• /
• pp.34-39
• /
• 2012

This study presents how low quality coal combustion affects the desulfurizer draft system by correlating of draft loss in a coal-fired thermal power plant and predicts the stall occurrence time of a booster fan. In case of low quality coal, a lot of coal is needed to generate equivalent output power, thereby the rating of increasing draft loss was faster than designed amount of coal. We surely confirmed that draft loss affects the specific energy of a booster fan strongly. On this basis, it is possible to predict the occurring time of stall for a booster fan from current operation specific energy to stall limit specific energy. This study suggests increasing speed of draft loss in each caloric value and the impact of specific energy at a booster fan, it expects to help safe operating in a thermal power plant.

• Proceedings of the KSEEG Conference
• /
• 2002.04a
• /
• pp.110-112
• /
• 2002

• 전기의세계
• /
• v.46 no.9
• /
• pp.36-46
• /
• 1997

본 해설에서는 철탑의 과도 접지저항은 물론 정상 접지저항의 측정과 관리에 대한 필요성을 강조하며, 일차적으로 765kV 심형기초 철탑의 정상 접지저항의 계산 및 측정에 관하여 설명한다.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.20 no.1
• /
• pp.50-54
• /
• 1983

Contact resistance variation which may be called sliding noise in carbon film variable resistors whose resistance elements consists of linear resistivity distribution were measured with several kinds of sliders and were analyzed to reduce the contact resistance variation. About the measuring method, the standard method of measuring contact resistance variation specified by the variable Resistance Components Institute was adupted. By analyzing the experimental results, it has been shown that the primary cause of contact resistance variation is due to current constriction and small discharge sparks in the resistance film in the area close to the slide contact. Moreover, it has been found that the sliding noise would be reduced by increasing the number of contact points, sliding speed, and pressure, and by using some kinds of insulation oil on the contacting surface. High contact resistance variation is likely to occur in the area of high resistance variation in a logrithmic resistance taper.

• 한국초전도학회:학술대회논문집
• /
• v.9
• /
• pp.343-347
• /
• 1999

We fabricated a resistive SFCL having a shunt resistor parallel to it in order to bifurcate the transient current at faults. The SFCL consists of a YBCO film coated with an Au layer (10 ${\omega}$ at room temperature), which is to disperse the heat generated at hot spots in the YBCO film, and the 5 ${\omega}$ shunt resistor. The minimum quench current of the SFCL was found to be 12.2 A$_{peak}$. This SFCL successfully controlled the fault current below 23 A$_{peak}$ which is otherwise to increase up to 113 A$_{peak}$. Bifurcation of the current resulted in the temperature rise of the YBCO/Au film 3 times slower than without the shunt, protecting the SFCL at high currents.

• Proceedings of the KIEE Conference
• /
• 2001.07d
• /
• pp.1982-1983
• /
• 2001

직류 100 kV 까지 고전압의 국가 측정표준을 확립하기 위하여 저항형 분압기의 비율을 정밀 측정하는 방법을 고안하였다. 일반적으로 저항형 분압기의 비율은 사용 전압에 따라 변하므로 저항과 전압비율을 동시에 측정하는 기술이 요구된다. 본 발표에서는 고안된 binary step-up 방법의 원리를 설명하고 실제 적용 시 예상되는 불확도를 계산하고자 한다.

• Geophysics and Geophysical Exploration
• /
• v.7 no.4
• /
• pp.251-255
• /
• 2004

Electric cables such as multi-interphone cables and ribbon cab]os are commonly used for data aquisition in the DC resistivity survey. In general, electromagnetic induction may occur in the electric cables when electric current flows through them. In case of using multi-interphone cables in the DC resistivity survey, electromagnetic induction could take place due to the entangled wires of the multi-interphone cables, when the current flows through them. Then, the electromagnetic induction may cause measured DC resistivity data to be distorted. In this study, a monitoring system with PXI (PCI Extention for Instrumentation) was constructed to examine signal distortion on the DC resistivity data, attributed to the electromagnetic induction. Common electric cables used in the DC resistivity survey were tested to observe the waveforms of the electric voltages. The waveforms measured were compared to examine signal distortion due to the electromagnetic induction. The results may provide information on the resistivity data obtained using different electric cables in the DC resistivity survey. The distortion of waveforms attributed to the electromagnetic induction wat not observed when using ribbon cables for DC resistivity data aquisition, while the distortion were observed when using multi-interphone. Therefore, the ribbon cables provide better quality of data than other cables in the DC resistivity data aquisition.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.13 no.5
• /
• pp.484-491
• /
• 2002

This paper presents the results of a study of voltage-controlled PIN diode attenuators for Ku-band satellite payload and suggests the temperature-compensation method of these attenuators. The PIN diode attenuators are designed using thin-film hybrid techniques. The load resistance for maximum linear characteristics is determined by simulation and measurements. In the case of APD0805, load resistance of 150 $\Omega$ gives attenuator up to 10 dB linear attenuation range per a PIN diode. Also, measurements over temperature of these PIN diode attenuators were performed. From these measurements, designed PIN diode attenuators shows the severe temperature dependency due to forward voltage variation. A temperature compensation method using thermistor is now suggested to compensate the temperature variation of these PIN diode attenuators. This circuit shows good linear characteristics over wide temperature range