• Journal of Advanced Marine Engineering and Technology
• /
• v.19 no.2
• /
• pp.47-55
• /
• 1995

When the low heavy oil is using as fuel oil to the diesel engine, some problems such as corrosion resistance, wear resistance and heat resistance are happened in diesel engine's internal material, especially the adhesive wear of piston ring groove was occurred as a important problem. Therefore to prevent adhesive wear of its groove, the surface of its groove used to be electroplated with Chrominum and for its Chromium electroplating, Fe anode is being used until nowadays because of its Special shape. However in case of using Fe anode, there were some problems such as deterioation of solution, property of Chromium film, and condition of coation. In this paper Pb anode electroplated withPb to the steel plate was investigated for its Chromium electroplating for Pb's high corrosion resistance in acid solution, and Pb anode is not dissolved compared with Fe anode and deterioration degree of solution in case of Pb anode is smaller than that of Fe anode and also property of Chromium film was better than that of Fe anode. Moreover it was known that the optimum cathodic current density for Pb electroplating to steel plate as insoluable anode for Chromium coating of piston ring groove is 30mA/$cm^2$ by experimental results obtained.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2018.06a
• /
• pp.138-138
• /
• 2018

선박을 통한 해상수송은 세계 무역의 80% 이상을 차지하고 있으며, 대부분의 선박은 저질중유의 연소로부터 추진력을 발생시키는 디젤 엔진을 원동력으로 사용하고 있다. 이러한 디젤 엔진은 연소의 부산물로 매년 백만 톤 이상의 오염물질을 방출하는데, 그 주성분은 탄소로 이루어져 있고 고온 열분해 또는 압축 점화 엔진의 작동 부산물들이 소량 포함되어 있다. 이에 본 연구에서는 선박으로부터 배출된 폐 수트를 리튬이온전지용 도전재로 활용하기 위한 독특한 방법이 제안되었다. 실험에 사용된 폐 수트는 운항중인 컨테이너선으로부터 수집되었으며, 수집된 폐 수트는 탄소 성분 이외의 불순물을 제거하고 흑연화 정도를 개선시키기 위해 $2,000^{\circ}C$로 열처리되었다. 열처리된 폐 수트의 모폴로지를 확인하기 위해 투과전자현미경을 이용하여 그 형상을 관찰하였으며, 이를 통해 폐 수트의 일차 입자는 지름이 약 70-100 nm 정도인 양파껍질 모양의 탄소(carbon nano-onion)로 형성된다는 것이 확인되었다. 또한, XRD, RAMAN 분광법 및 BET 분석 결과를 통해, 열처리된 폐 수트가 결정성이 있는 흑연으로 재형성되었으며 비표면적은 일반적으로 사용되는 활물질에 비해 약간 더 높다는 것을 확인할 수 있었다. 한편, 이러한 특성은 리튬이온전지용 도전재로 활용될 수 있는 가능성을 보여주었고, 이는 전기화학적 정전류 충전 및 방전 테스트를 통해 그 성능이 확인되었다. 일반적으로 사용되는 도전재의 테스트 결과와 폐 수트를 도전재로 사용한 테스트 결과를 Fig. 1에 나타내었다. 이상의 실험 결과들을 미루어 볼 때, 선박으로부터 배출된 폐 수트가 리튬전지용 음극 활물질 및 도전재로 재활용될 수 있을 것으로 사료된다.

• Resources Recycling
• /
• v.2 no.2
• /
• pp.39-44
• /
• 1993

This study was carried out to remove the water from low grade anthracite slurry produced at Eoryong coal mine by the oil agglomeration process. 80% of Anthracite as a coal oil mixture (COM) was separated from water by the difference of specific gravity. Then, the amount of kerosene, diesel oil, and heavy oil forming COM was 10% of the amount of sample, respectively. The recovery rate of combustibles and ash content of agglomerated anthracite were affected largely by the amount of added oil, pulp density, particle size, mixing time, and impeller speed. The recovery rate of combustibles was increased to 95% and ash content was decrea-sed from 30% to 13.5% under the optimum conditions.

• Journal of Advanced Marine Engineering and Technology
• /
• v.38 no.4
• /
• pp.409-417
• /
• 2014

Since the oil price has been significantly jumped for recent some years, the diesel engine of the merchant ship has been mainly used the heavy oil of low quality. Thus, it has been often exposed to severely corrosive environment more and more because temperature of the exhaust gas in a combustion chamber is getting higher and higher with increasing of using the heavy oil of low quality. As a result, wear and corrosion of most parts surrounded with combustion chamber is more serious compared to the other parts of the engine. Therefore, an optimum weldment for these parts is very important to prolong their lifetime in a economical point of view. In this study, four types of filler metals such as Inconel 625, 718, 1.25Cr-0.5Mo and 0.5Mo were welded with SMAW and GTAW methods in the forged steel which would be generally used with piston crown material. And the corrosion properties of weld metal, heat affected zone and base metal were investigated using electrochemical methods such as measurement of corrosion potential, anodic polarization curves, cyclic voltammogram and impedance etc. in 35% H2SO4 solution. The weld metal and base metal exhibited the best and worst corrosion resistance in all cases of filler metals. In particular, the weld metal welded with filler metals of Inconel 718 revealed the best corrosion resistance among the filler metals, and Inconel 625 followed the Inconel 718. Hardness relatively indicated higher value in the weld metal compared to the base metal. Furthermore, Inconel 625 and 718 indicated higher values of hardness compared to 1.25cr-0.5Mo and 0,5Mo filler metals in the weld metal.

• Proceedings of KOSOMES biannual meeting
• /
• 2006.11a
• /
• pp.291-297
• /
• 2006

Recently it is a tendency that the use of the heavy fuel oil is investigated even from the middle&small class vessel in order to reduce the operating cost of vessel caused by with rise of international gas price. In this study, analyzed the physical & chemical properties and examined the effect of refining treatment and a fuel oil additive for MF30 fuel oil which is a mixture fuel oil mixed M.G.O and the heavy oil MF380 use to be possible in the middle&small class vessel. As a results, the effects of two of pre-refinery treatment methods as centrifugal purifier and heating & homogenizing system(M.C.H) are some feeble, but the pour point and the flash point came to be low more or less. The effect of property improvement which is caused by with the fuel oil additive did not appear positively.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.13 no.1 s.28
• /
• pp.39-45
• /
• 2007

Recently it is a tendency that the heavy fuel oil is considered to be used on board even middle or small sized vessels in order to reduce the operating cost of vessel mused by a rise in international oil prices. In this study, analyzed the physical & chemical properties and examined the effect of refining treatment and a fuel oil additive for MF30 fuel oil which is a mixture fuel oil mixed M.G.O and the heavy oil MF380 use to be possible in the middle&small class vessel. As a results, the effects of two of pre-refinery treatment methods as centrifugal purifier and heating & homogenizing system(M.C.H) are some feeble, but the pour point and the flash point came to be low more or less. The effect of property improvement which is mused by the fuel oil additive did not appear positively.