• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.6
• /
• pp.626-633
• /
• 2005

This paper proposes a new 2MVA SSFG(Sag Swell Flicker Generator) injecting voltage by using series inverter. The proposed SSFG composes series inverter, DC capacitor as energy storage, rectifier and voltage clamp circuit. This SSFG is designed to generate typical power disturbances, such as voltage sag/swell, over/under voltage and voltage flicker. Also it is designed to generate unexpected voltage phase jumping waveform by controlling the series inverter. In this paper, three kinds of control methods for the proposed 2MVA SSFG we investigated by PSIM simulation. Also typical voltage sag, swell, flicker waveforms are implemented by adopting effective control method.

• Food Science of Animal Resources
• /
• v.23 no.3
• /
• pp.221-226
• /
• 2003

This study investigated the effect of different electrical stunning methods on pH, water holding capacity(WHC), cooking loss(CL), meat color and blood spot rate in broilers. One-hundred and forty broiler chickens were slaughtered by 50, 65 and 90 voltage with the same electrical frequency(255 Hz) and stunning time(5 sec) in commercial abattoir. The ultimate pH of leg muscle and WHC of breast muscle decreased with increasing the stunning voltage. However, there were no significant differences in ultimate pH, WHC and CL of breast muscle, and ultimate pH of leg muscle. Lightness(L*) and yellowness(b*) values of leg muscle stunned with 90V, 255 Hz, 5 sec were higher than those stunned with 50V, 255 Hz for 5 sec(p<0.05). But there were no significant differences in color value on skin, breast and wing muscle. Our experiments showed that change of stunning voltage affected some broiler meat quality parameters. However, further research is necessary to examine the effects of stunning condition on broiler meat quality.

• Journal of Navigation and Port Research
• /
• v.28 no.3
• /
• pp.213-219
• /
• 2004

In this paper, a LNA(Low Noise Amplifier) has been developed, which is operating at L-band i.e., 1452∼1492 MHz for satellite DAB(Digital Audio Brcadcasting) receiver. The LNA is designed to improve input and output reflection coefficient and VSWR(Voltage Standing Wave Ratio) by balanced amplifier. The LNA consists of low noise amplification stage and gain amplification stage, which make a using of GaAs FET ATF-10136 and VNA-25 respectively, and is fabricated by hybrid method. To supply most suitable voltage and current, active bias circuit is designed Active biasing offers the advantage that variations in $V_P$ and $I_{DSS}$ will not necessitate a change in either the source or drain resistor value for a given bias condition. The active bias network automatically sets $V_{gs}$ for the desired drain voltage and drain current. The LNA is fabricated on FR-4 substrate with RF circuit and bias circuit, and integrated in aluminum housing. As a reults, the characteristics of the LNA implemented more than 32 dB in gain. 0.2 dB in gain flatness. lower than 0.95 dB in noise figure, 1.28 and 1.43 each input and output VSWR, and -13 dBm in $P_{1dB}$.

• Proceedings of the KIPE Conference
• /
• 2016.11a
• /
• pp.71-72
• /
• 2016

전동기의 운전 영역을 확대하기 위해 부스트 컨버터를 이용하여 가변 DC link를 합성한다. 가변 DC link 구간에서는 스위칭 손실이 증가하기 때문에 스위칭 횟수를 줄이는 전략이 필요하다. 제안하는 Edge-Cutting Pulse Width Modulation(ECPWM)을 통해 스위칭 손실을 1/3로 절감하고, 최적의 고조파 특성을 갖는 직류단 전압의 크기를 결정한다. 이를 이용해 가변 직류단 전압 구간에서 인버터 손실을 감소시키며, Bolognani 과변조 방법을 적용해 안정적인 6-스텝으로의 절환까지 고려한다.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.12 no.3
• /
• pp.132-138
• /
• 1998

The dynamic analysis of stability in industrial power system is an important subject. In this paper, the effect of voltage dips for short duration (short-circuit) in the utility system on generators, synchronous motors of the industrial plant and the measures to be adopted to reduce the undesired effects of voltage dips re investigated. In the case of utility three-phase short-circuits of longer duration, both the generators and synchronous motors in the plant may become unstable. In order to avoid instability through fault clearing in the second zone time a decoupling device is necessary. The instability of voltage can be avoided with a well suited setting time of disconnecting device and load trip.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2002.11a
• /
• pp.462-466
• /
• 2002

This paper describes a low frequency electrical nerve stimulator for muscle care. The developed system consist of 8bit low power consumed MPU, voltage boosting circuit converting 9V input to 120V output, repairing circuit for distorted output pulse, LED and buttons for I/O, and electro-chemical pad. The pulse generation algorithm for the muscle care effect is developed with basic pulses such as a single phase rectangle pulse, symmetric rectangle pulse, and depolarized interrupt pulse.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.8
• /
• pp.54-61
• /
• 2001

A fully on-chip open-drain CMOS output driver was designed for high bandwidth DRAMs, such that its output voltage swing was insensitive to the variations of temperature and supply voltage. An auto refresh signal was used to update the contents of the current control register, which determined the transistors to be turned-on among the six binary-weighted transistors of an output driver. Because the auto refresh signal is available in DRAM chips, the output driver of this work does not require any external signals to update the current control register. During the time interval while the update is in progress, a negative feedback loop is formed to maintain the low level output voltage ($V_OL$) to be equal to the reference voltage ($V_{OL.ref}$) which is generated by a low-voltage bandgap reference circuit. Test results showed the successful operation at the data rate up to 1Gb/s. The worst-case variations of $V_{OL.ref}$ and $V_OL$ of the proposed output driver were measured to be 2.5% and 7.5% respectively within a temperature range of $20^{\circ}C$ to $90^{\circ}C$ and a supply voltage range of 2.25V to 2.75V, while the worst-case variation of $V_OL$ of the conventional output driver was measured to be 24% at the same temperature and supply voltage ranges.

• Science of Emotion and Sensibility
• /
• v.21 no.2
• /
• pp.137-144
• /
• 2018

The study figured out the operational conditions of a two-way movement actuator made of one-way shape memory alloy (OWSMA) for versatile ventilation intelligent garments. To develop a low-power actuator that consumes energy only when a garment changes its form such as opening and closing, multiple channels of OWSMA were used, and optimum diameter of the wires was examined. For the switch device, optimum voltage application unit time was determined. Optimum diameter of OWSMA wire was determined by applying 3.7V to the pre-determined candidate diameters, which demonstrated two-way operation in previous studies. In order to evaluate the optimum voltage application time, the internal diameter of the actuator was measured while increasing and decreasing by 50 ms from the unit time of voltage application. Delay time under two-way operation of the actuator was measured to minimize interference caused by heat between channels. Power of 3.7V was applied to OWSMA for assessment of optimal time, and the whole process from heating to cooling was video-recorded with a thermal image camera to determine the point of time at which the temperature of OWSMA wire dropped below the phase transformation temperature. The results showed that $0.4{\Phi}$ was the most suitable diameter, and the optimum unit time of voltage applied to open and close the actuator was 4100ms. It was also shown that the delay time should be more than 1.8 seconds between two-way operations of the actuator.

• Proceedings of the KIPE Conference
• /
• 2014.07a
• /
• pp.277-278
• /
• 2014

본 논문은 저 대기전력의 구현이 가능하며 출력전압을 정확하게 제어할 수 있는 플라이백 컨버터 제어방식을 제안한다. 제안 방식은 모든 절연 형 컨버터에 적용 가능하고, 2차 측에 PFM(Pulse Frequency Modulation) IC를 위치시켜 정확한 출력전압 제어가 가능하다. 또한, 1,2차 측간에 신호 전달을 위하여 기존에 사용되는 TL431과 포토커플러가 아닌 Y-capacitor와 Low-Pass-Filter를 적용하여, 저 대기전력 구현이 가능하다. 제안방식의 타당성을 검증하기 위하여 이론적 해석과 시뮬레이션을 통하여 가능성을 확인하였다.

• Journal of IKEEE
• /
• v.24 no.1
• /
• pp.132-139
• /
• 2020

The ionizer module used in this air cleaner supplies high voltages of 3.5KV / -4KV to the discharge electrode HV+ / HV- using a winding transformer to generate positive and negative ions by electric field radiation of carbon fiber brush. The ionizer module circuit using the existing MCU has the disadvantage of large PCB size and expensive price, and the gate driver chip using the existing ring oscillator has oscillation period sensitive to PVT (Process-Voltage-Temperature) fluctuation and there is risk of fire or electric shock because there is no fault detection function by short circuit of HV+ and GND as well as HV- and GND. Therefore, in this paper, even though PVT fluctuates, by using 7-bit binary up counter, HV+ voltage reaches the target voltage by adjusting oscillation period. And an HV+ short fault detection circuit for detecting a short circuit between HV+ and GND, an HV- short fault detection circuit for detecting a short circuit between HV- and GND, and an OVP (Over-Voltage Protection) for detecting that HV+ rises above an overvoltage are newly proposed.