• The Journal of the Acoustical Society of Korea
• /
• v.36 no.4
• /
• pp.238-246
• /
• 2017

High frequency ultrasound imaging typically suffers from low sensitivity due to the small aperture of high frequency transducers and shallow imaging depth due to the frequency-dependent attenuation of ultrasound. These limitations should be overcome to obtain high-frequency, high- resolution ultrasound images. One practical solution to the problems is a high-performance signal receiver capable of detecting a very small signal and amplifying the signal with minimal electronic noise addition. This paper reports a recently developed low-noise, wideband ultrasound receiver for high-frequency, high-resolution ultrasound imaging. The developed receiver has an amplification gain of up to 73 dB and a variable amplification gain range of 48 dB over an operating frequency of 80 MHz. Also, it has an amplification gain flatness of ${\pm}1dB$. Due to these high performances, the developed receiver has a signal-to-noise ratio of at least 8.4 dB and a contrast-to-noise ratio of at least 3.7 dB higher than commercial receivers.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.25 no.3
• /
• pp.282-288
• /
• 2014

In this paper, we have analyzed and designed a digital RF receiver based on the optimization of the dynamic range parameter to secure the wideband characteristics and linearity of digital radar receivers. To improve the wideband characteristics and dynamic range, a low noise amplifier is matching design with a noise source to minimize the noise figure in 1 GHz bandwidth and we improved the linearity of RF-receiver by securing the conversion gain characteristics of receiver through the design of active mixer. RF receiver is designed to give gain 63 dB, noise figure 1.2 dB and dynamic range of RF receiver has 75.8 dB in a wide band of 8.8~9.8 GHz. It is shown to be applicable to X-band digital radar receiver.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.11 no.12
• /
• pp.1193-1200
• /
• 2016

In this paper, we developed a system for measuring a passive intermodulation distortion signal of the mobile communication RF module having a wide band characteristic. The Broadband was designed to represent the characteristics of the receiver to meet the low noise characteristics and wideband characteristics in the RF receiver were to represent a wide dynamic range(high dynamic range)from the RF receiving end. PIMD designed passive intermodulation distortion signal measured by applying the FPGA / DSP in the system was measured to record the program on the PC. Variable up to 650MHz-2700MHz showed up to-138dBc measured PIMD3.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2016.10a
• /
• pp.703-705
• /
• 2016

In this paper, we developed a wideband PIMD system to measure passive intermodulation distortion signals of mobile communication RF passive module. To represent wideband characteristic, we designed a receiver that meets low-noise and wideband characteristics in RF receiver. It allows high dynamic range in the RF receiver front end. In designed passive intermodulation distortion measurement system, we programed to display a PIMD signal with FPGA/DSP at PC. Implemented PIMD system was variable from 650 MHz to 2700 MHz and show up to -138 dB minimum detectable $3^{rd}$ passive inetrmodulation distortion signal.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.21 no.10
• /
• pp.1169-1176
• /
• 2010

The RF front-end for L1/L2 dual-band Global Positioning System(GPS) receiver is presented in this paper. The RF front-end(down-converter) using low IF architecture consists of a wideband low noise amplifier(LNA), a current mode logic(CML) frequency divider and a I/Q down-conversion mixer with a poly-phase filter for image rejection. The current bleeding technique is used in the LNA and mixer to obtain the high gain and solve the head-room problem. The common drain feedback is adopted for low noise amplifier to achieve the wideband input matching without inductors. The fabricated RF front-end using $0.18{\mu}m$ CMOS process shows a gain of 38 dB for L1 and 41 dB for L2 band. The measured IIP3 is -29 dBm in L1 band and -33 dBm in L2 band, The input return loss is less than -10 dB from 50 MHz to 3 GHz. The measured noise figure(NF) is 3.81 dB for L1 band and 3.71 dB for L2 band. The image rejection ratio is 36.5 dB. The chip size of RF front end is $1.2{\times}1.35mm^2$.

• Journal of the Korean Institute of Intelligent Systems
• /
• v.27 no.2
• /
• pp.144-149
• /
• 2017

In this paper, we developed an intelligent and wideband RF-receiver module to represent a high dynamic range and good linearity characteristics up to 650MHz-2700MHz frequency band. and implemented an intelligent digital-RF- distorted signal measuring system for the RF distortion (intermodulation) signals. Broadband RF-receive module was designed to represent the optimized linear parameters of the receiver to meet the low noise and wide dynamic range. The designed intelligent digital-distortion(intermodulation) signal measument system measured by applying the 1MHz IF of third intermodulation signal of DUT and Measured data was recorded by program on the PC monitor with GUI interface. By variable up to 650MHz-2700MHz measured data showed up to -127.8dBc to -138dBc of the distortion (intermodulation) signal. And developed intelligent digital- distortion signal measurement system can be used to measure intermodulation distortion signal of wireless system widely.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.16 no.10 s.101
• /
• pp.1050-1058
• /
• 2005

This paper presents how to design and implement a very compact, cost effective and broad band receiver module for IEEE 802.16 FWA(Fixed Wireless Access) in the 40 GHz band. The presented receiver module is fabricated in a multi-layer LTCC(Low Temperature Cofired Ceramic) technology with cavity process to achieve excellent electrical performances. The receiver consists of two MMICs, low noise amplifier and sub-harmonic mixer, an embedded image rejection filter and an IF amplifier. CB-CPW, stripline, several bond wires and various transitions to connect each element are optimally designed to keep transmission loss low and module compact in size. The LTCC is composed of 6 layers of Dupont DP-943 with relative permittivity of 7.1. The thickness of each layer is 100 um. The implemented module is $20{\times}7.5{\times}1.5\;mm^3$ in size and shows an overall noise figure of 4.8 dB, an overall down conversion gain of 19.83 dB, input P1 dB of -22.8 dBm and image rejection value of 36.6 dBc. Furthermore, experimental results demonstrate that the receiver module is suitable for detection of Digital TV signal transmitted after up-conversion of $560\~590\;MHz$ band to 40 GHz.