• Analytical Science and Technology
• /
• v.25 no.2
• /
• pp.91-101
• /
• 2012

A list of volatile fatty acids (VFA) including propionic acid, butyric acid, isovaleric acid, valeric acid, etc. is well known for offensive odorants. The analysis of odorant VFA is a highly delicate task due to high reactivity and unstable recovery rate. At present, analytical methods of VFA are recommended to include alkali impregnation filter method and alkali absorption method by the malodor prevention law of the Korea Ministry of Environment (KMOE). In this review, a survey has been made to explore various approaches available for the analysis of VFA to include both official methods of the KMOE and others. In light of the unreliability of those established analytical methods, it is highly desirable to develop some substituting methods for VFA. Among such options, one may consider such option as sorbent tube (ST) sampling and cryogenic trapping-thermal desorption technique. Moreover, procedures used for standard preparation, sampling steps, and instrumental detection stage are also evaluated. Application of container sampling (like Tedlar bag) is however not recommendable due to significant (sorptive) loss in sampling and in storage stage. In the detection stage, the use of GC/MS is recommendable to replace GC/FID due to the presence of diverse interfering substances. Thus, it is essential to properly establish the basic quality assurance (QA) for VFA analysis in air.

• Journal of Korean Society of Environmental Engineers
• /
• v.29 no.9
• /
• pp.1027-1034
• /
• 2007

This research was focused on the selective separation of $CO_2$ or $CH_4$ from mixture of these gases, by controlling the size of pore or pore gate. Pitch based activated carbon fibers(ACF) were used as adsorbents. The size of pore gate was controlled by the molecule having similar size to that of pore opening. After the adsorption of adsorbate on pore surface, planar molecules such as benzene and naphthalene covered the pore gate. The slow release of adsorbate from the pores covered by planar molecules makes apertures between planar molecules covering pore gate and this structure can be fixed by rapid pyrolysis. The control of pore gate using benzene as covering molecules could not accomplished due to the simultaneous volatilization of benzene and adsorbate$(CO_2)$ caused by similar temperatures of benzene volatilization and adsorbate desorption. Therefore we replaced benzene with naphthalene looking for the stability at a $CO_2$ desorption temperature. The naphthalene molecule was adsorbed on the ACF up to 15% of ACF weight and showed no desorption until $100^{\circ}C$, indicating that the molecule could be used as a good cover molecule. Naphthalene could cover almost all the pore gate, reducing BET surface area from 753 $m^2/g$ to 0.7 $m^2/g$. A mixed gas$(CO_2:CH_4=50:50)$ was adsorbed on the naphthalene treated OG-7A ACF. The amount of $CO_2$ adsorption increased with total pressure, whileas thai of $CH_4$ was not so much influenced on the pressure, indicating that $CO_2$ made more compounds on the ACF surface along with total pressure increase. The most $CO_2$ and the least $CH_4$ were adsorbed in the condition of 0.4 atm, resulting in the highly pure $CH_4$ left in ACF.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.348-348
• /
• 2014

차세대 디스플레이 구동 회로 소자를 위한 재료로서, Amorphous Oxide Semiconductor (AOS)가 주목받고 있다. AOS는 기존의 Amorphous Silicon과 비교하여 뛰어난 이동도를 가지고 있으며, 넓은 밴드 갭에 의한 투명한 광학적 특성을 가지고 있다. 이러한 장점을 이용하여, AOS 박막은 thin film transistor (TFT)의 active channel로 이용 되고 있다. 하지만, AOS를 이용한 TFT의 경우, 시간이 경과함에 따라 $O_2$ 및 $H_2O$ 흡착에 의해 전기적 특성이 변하는 현상이 있다. 이러한 현상은 소자의 신뢰성에 있어 중요한 문제가 된다. 이러한 문제를 연구하기 위해 본 논문에서는, AOS 박막을 이용하여 bottom 게이트형 TFT를 제작하였다. 이를 위해 먼저, p-type Si 위에 건식산화방식으로 $SiO_2$(100 nm)를 성장시켜 게이트 산화막으로 이용하였다. 그리고 Zn과 Sn이 1: 2의 조성비를 가진 ZnSnO (ZTO) 용액을 제조한 후, 게이트 산화막 위에 spin coating 하였다. Splin coating된 용액에 남아 있는 솔벤트를 제거하기 위해 10분 동안 $230^{\circ}C$로 열처리를 한 후, 포토리소그래피와 에칭 공정을 이용하여 ZTO active channel을 형성하였다. 그 후, 박막 내에 남아 있는 불순물을 제거하고 ZTO TFT의 전기적인 특성을 향상시키기 위하여, $600^{\circ}C$의 열처리를 30분 동안 진행 하여 junctionless형 TFT 제작을 완료 하였다. 제작된 소자의 시간 경과에 따른 열화를 확인하기 위하여, 대기 중에서 2시간마다 HP-4156B 장비를 이용하여 전기적인 특성을 확인 하였으며, 이러한 열화는 후처리 공정을 통하여 회복시킬 수 있었다. 열화의 회복을 위한 후처리 공정으로, 퍼니스를 이용한 고온에서의 열처리와 microwave를 이용하여 저온 처리를 이용하였다. 결과적으로, TFT는 소자가 제작된 이후, 시간에 경과함에 따라서 on/off ratio가 감소하여 열화되는 경향을 보여 주었다. 이러한 현상은, TFT 소자의 ZTO back-channel에 대기 중에 있는 $O_2$ 및 $H_2O$의 분자의 물리적인 흡착으로 인한 것으로 보인다. 그리고 추가적인 후처리 공정들에 통해서, 다시 on/off ratio가 회복 되는 현상을 확인 하였다. 이러한 추가적인 후처리 공정은, 열화된 소자에 퍼니스에 의한 고온에서의 장시간 열처리, microwave를 이용한 저온에서 장시간 열처리, 그리고 microwave를 이용한 저온에서의 단 시간 처리를 수행 하였으며, 모든 소자에서 성공적으로 열화 되었던 전기적 특성이 회복됨을 확인 할 수 있었다. 이러한 결과는, 저온임에도 불구하고, microwave를 이용함으로 인하여, 물리적으로 흡착된 $O_2$ 및 $H_2O$가 짧은 시간 안에 ZTO TFT의 back-channel로부터 탈착이 가능함과 동시에 소자의 특성을 회복 가능 함 의미한다.

• Clean Technology
• /
• v.29 no.3
• /
• pp.217-226
• /
• 2023

The amount of hydrogen adsorbed in arrays of single walled carbon nanotubes (SWNTs) was studied as a function of nanotube diameter and distance between the nearest-neighbor nanotubes on square arrangements using a grand canonical Monte Carlo simulation. The influence of the geometry of a triangle array with the same diameters and distances was also studied. Hydrogen-carbon and hydrogen-hydrogen interactions were modeled with Lennard-Jones potentials for short range interactions and electrostatic interactions were added for hydrogen-hydrogen pairs to consider quantum contributions at low temperatures. At 194.5 K, Type I isotherms for large-diameter SWNTs and Type IV isotherms without hysteresis between adsorption and desorption processes for wider tube separations were observed. At 200 bars, the gravimetric hydrogen storage capacity of the SWNTs was reached or exceeded the US Department of Energy (DOE) target, but the volumetric capacity was about 70% of the DOE target. At 77 K, a two-step adsorption was observed, corresponding to a monolayer formation step followed by a condensation step. Hydrogen was adsorbed first to the inner surface of the nanotubes, then to the outer surface, intratubular space and the interstitial channels between the nanotube bundles. The simulation indicated that SWNTs of various diameters and distances in a wide range of configurations exceeded the DOE gravimetric and volumetric targets at under 1 bar.

• Clean Technology
• /
• v.17 no.2
• /
• pp.166-174
• /
• 2011

The xAl-yCe oxide catalysts with different mol ratios of Al/(Al+Ce) were prepared by a co-precipitation method and Pt supported on xAl-yCe oxide catalysts were synthesized by an incipient wetness impregnation method. The catalysts were characterized by X-ray Diffraction (XRD), $N_2$ sorption, and $H_2$/CO-temperature programmed reduction ($H_2$/CO-TPR) to correlate with catalytic activities in co oxidation. Among the catalysts studied here, Pt/1Al-9Ce oxide catalyst showed the highest activity in dry and wet reaction conditions and the catalytic activity showed a typical volcano-shape curve with respect to Al/(Al+Ce) mol ratio. When the presence of 5% water vapor in the feed, the temperature of $T_{50%}$ was shifted ca. $30^{\circ}C$ to lower temperature region than that in dry condition. From CO-TPR, the desorption peak of $CO_2$ on Pt/1Al-9Ce oxide catalyst showed the highest value and well correlated the catalytic performance. It indicates that the Pt/1Al-9Ce oxide catalyst has a large amount of active sites which can be adsorbed by co and easy to supplies the needed oxygen. In addition, the amount of pentacoordinated $Al^{3+}$ sites obtained through $^{27}Al$ NMR analysis is well correlated the catalytic performance.

• Journal of Korean Society for Atmospheric Environment
• /
• v.30 no.1
• /
• pp.77-87
• /
• 2014

In this study, an experimental approach to measure a suite of low weight hydrocarbons was investigated with an emphasis on ethylene (EL) along with many others (ethane (EA), propane (PA), propylene (PL), n-butane (BA), acetylene (AL), methyl acetylene (ML)). Their concentrations were quantified using GC-FID system equipped with thermal desorption (TD) system. The TD-based analysis was conducted using both Link Tube/Thermal Desorber (LT/TD) method and Modified Injection through a Thermal Desorption (MITD) method. The results of these analyses were evaluated in a number of respects. The system allowed the detection of all compounds except methane with the mean response factor (RF) of 10.28 (EA) to 11.94 (PL). The method detection limits of target compounds were seen in the range of 0.027 (ML) to 0.146 ng (BA). The emission flux of some environmental samples (fruits), when measured using a small flux chamber system, fell in the range of 0.14 (AL: Kiwi) to $181ng{\cdot}g^{-1}{\cdot}hr^{-1}$ (EL: Apple Peel). The results of this study confirm that the experimental approach developed in this study allows to accurately measure emissions of low weight hydrocarbons (LWHC) like ethylene from various natural and man-made source processes.

• Journal of the Korean Vacuum Society
• /
• v.5 no.3
• /
• pp.239-244
• /
• 1996

We firstly report that formation of $SiO_2$ layer on Si surface can be effectively prevented by flowing the $Si_2H_6$ gas during the heating-up procedure for amorphous Si depositions. In this way, amorphously deposited Si layer onto crystalline Si substrates can be grown epitaxially during the post-deposition heat treatments. The suppression of surface $SiO_2$ can be explained in terms of adsorption of SiHx adspecies, instead of oxygen from residual gases in the reactors, to Si surfaces after desorption of hydrogen from H-passivated Si surfaces. Employing $Si_2H_6$ flowing and soild phase epitaxial growth, high-quality epitaxial Si layer can be obtained at low temperatures below $600^{\circ}C$ without conventional high temperature cleaning procedures.

• Applied Chemistry for Engineering
• /
• v.10 no.3
• /
• pp.343-348
• /
• 1999

The iron silicide films were prepared by chemical vapor deposition method using rf-plasma in variations of substrate temperature. rf-power, and ratio of $SiH_4$ and Fe-precursor. While iron silicide films are generally grown by ion beam synthesis (IBS) method of multi-step process, it is confirmed that iron silicide or $\beta$-phase consolidated $Fe_aSi_bC_cH_d$ was formed by one-step process in this study. The characteristics of films is variable because the different amounts of carbon and hydrogen was involved in the films as a function of dilute ratio of Fe-precursors and silane. It was shown that the different characteristics of films in carbon and hydrogen following the ratio of Fe-precursor and silane. The optical gap energy of films fabricated according to substrate temperature was invariant because active site brought in desorption of hydrogen was limiled. When rf-power was above 240 watt, the optical gap energy turned out to have high values because of dangling bonds increased by etching.

• Applied Chemistry for Engineering
• /
• v.19 no.5
• /
• pp.512-518
• /
• 2008

The present work studied the selective catalytic reduction (SCR) of NO to $N_2$ by $NH_3$ over $V/TiO_2$ focusing on NOx control for the stationary sources. The SCR process depends mainly on the catalyst performance. The reaction characteristics of SCR with $V/TiO_2$ catalysts were closely examined at low and high temperature. In addition, adsorption and desorption characteristics of the reactants on the catalyst surface were investigated with ammonia. Seven different $TiO_2$ supports containing the same loading of vanadia were packed in a fixed bed reactor respectively. The interaction between $TiO_2$ and vanadia would form various non-stoichiometric vanadium oxides, and showed different reaction activities. There were optimum calcination temperatures for each samples, indicating different reactivity. It was finally found from the $NH_3-TPD$ test that the SCR activity was nothing to do with $NH_3$ adsorption amount.

• Korean Chemical Engineering Research
• /
• v.53 no.3
• /
• pp.401-406
• /
• 2015

Getter is a class of materials used in absorbing gases such as hydrogen and moisture in microelectronics or semiconductor devices to operate properly. In this study, we developed a new device structure consisting of porous anodized alumina films on textured silicon wafer, which have cost efficiency in materials and processing aspects. Anodic aluminum oxide (AAO) with controlled pore sizes can be applied to a high-efficiency moisture absorber due to the high surface area and OH- saturated surface property. The moisture sorption capacity was 2.02% (RH=35%), obtained by analyzing isothermal adsorption/desorption curve.