• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.37 no.2
• /
• pp.187-192
• /
• 2013

Thin metallic sandwich plate with pyramidal metallic inner structures is manufactured from a continuous projection welding between face sheets and inner structures. Due to the welding pressure, imperfections of inner structures induced by the deformation of the inner structures occur. The imperfections affect the response of the thin metallic sandwich plate subjected to low-velocity impact loading. The goal of this paper is to obtain a proper dominant imperfection mode of the thin metallic sandwich plate with pyramidal metallic inner structures. The variation of impact responses of the thin metallic sandwich plate for different imperfection modes are investigated by finite element analysis. The results of the FE analysis are compared to those of drop impact experiments. From the results of the comparison, it has been shown that the dominant imperfection mode of the thin metallic sandwich plate with pyramidal metallic inner structures is all type of symmetric imperfection mode with symmetrical imperfections of four struts.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2006.11a
• /
• pp.339-343
• /
• 2006

Model SCRamjet Engine intake is designed for Ground test. The designed Intake provides hot and slow flow with the combustor. Flow separation is controlled by the shock wave segregation based on the Korekegi criteria. With Kantrowitz limit analysis, side wall cut out region is also set for the self start.

• Proceedings of the Korean Society of Marine Engineers Conference
• /
• 2006.06a
• /
• pp.29-30
• /
• 2006

나이모닉 일체형으로 사용되고 있는 선박용 2 행정 저속엔진의 배기밸브 스핀들을 고온, 고압, 배기가스 및 반복 충격 하중에 노출된 스핀들의 Head부분은 기존의 나이모닉 소재를 적용, 기존 재질의 우수한 성질을 유지하고 설계적으로 나이모닉 소재의 적용이 불필요한 Stem부는 오스텐나이트 계열의 SNCrW 소재를 사용하여 관성마찰 용접 방식으로 접합하여 제품을 제작하고, 접합부의 미세조직 관찰, 성분분석, 인장, 경도, 피로시험 등의 기계적, 금속적 특성평가를 통해 마찰용접제품에 대한 신뢰성을 확인하고 양산 생산을 위한 기술적 토대를 마련하였다.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.15 no.5
• /
• pp.95-107
• /
• 2016

The axle weight of a vehicle in motion can be measured with a low-speed or high-speed weigh-in-motion (WIM). However, the axial load dynamically change depending on the vehicle's characteristics-such as the chassis or axle structure-or the characteristics of the driving environment such as road flatness. The changes in dynamic load lead to differences between the vehicle's weight measured at rest and the vehicle's weight measured in motion. For this Study, an experiment was conducted with an instrumented vehicle to analyze the range of errors caused by uncontrollable environmental factors by identifying the characteristics of the dynamic load changes of a vehicle in motion, and determine the appropriate scale for the accuracy evaluation of a high-speed WIM, as a preparatory research for the introduction of unmanned overweight enforcement systems in the future. The key findings from the experiment are summarized as follows. First, The gross weight of the tested vehicle changed by approximately 1% at low velocities and approximately by 4% at high velocities, and the vehicle's axle weight changed by approximately 1-3%, at low velocities and by 2-9% at high velocities. A single axle showed larger weight changes than individual axles in a group. Secondly, The vehicle's gross weight and the axle weight on the impact section were up to eight times and three-to-twelve times higher, respectively, than its gross weight and the axle weight on the flat section. The vibration frequency of the vehicle's dynamic load was measured at between 2.4 and 5.8Hz, and found to return to the normal amplitude after moving approximately 30 meters.

• Journal of Aerospace System Engineering
• /
• v.12 no.4
• /
• pp.106-111
• /
• 2018

Hydrodynamic ram phenomenon could be generated by external threats such as impact and blast in the aircraft. High strain rate deformation caused by the hydrodynamic ram phenomenon is one of the main factors to influence structural survivability. Mechanical properties of composite structure change rapidly under conditions of high strain rate. Therefore, it is necessary to experimentally investigate the influence of strain rates for aircraft structural survivability. In this paper, tensile tests of composite material were conducted for low and high strain rates to investigate the influence of the various strain rates. Tensile modulus increases more compared to tensile strength at high strain rate under hydrodynamic ram condition. Regression analysis was conducted to predict tensile modulus at various strain rates because it is one of the main damaging factors for composite structures under high strain rate conditions. Also, the mechanical properties of composite materials were acquired and analyzed under high strain rate conditions. It is hypothesized that the results from this study would be used for designing aircraft composite structures and evaluation considering structural survivability.

• Composites Research
• /
• v.34 no.5
• /
• pp.317-322
• /
• 2021

When a complex load such as torsion, low-speed impact, or fatigue load is applied, the properties in the thickness direction are weakened through microcracks inside the material due to the nature of the laminated composite material, and delamination occurs. To prevent the interlaminar delamination, various three-dimensional reinforcement methods such as Z-pinning and stitching, and structural health monitoring techniques that detect the microcrack of structures in real time have been continuously studied. In this paper, the single-lap joints with I-fiber stitching process were manufactured by a co-curing method and their strengths and failure detection capability were evaluated. AE and electric resistance method were used for detection of crack and failure signal and electric circuit for signal analysis was manufactured, and failure signal was analyzed during the tensile test of a single-lap joint. From the experiment, the strength of the single lap joint reinforced by I-fiber stitching process was improved by about 44.6% compared to the co-cured single lap joint without reinforcement. In addition, as the single-lap joint reinforced by I-fiber stitching process can detect failure in both the electrical resistance method and the AE method, it has been proven to be an effective structure for failure monitoring as well as strength improvement.