• Composites Research
• /
• 제26권1호
• /
• pp.36-41
• /
• 2013

본 연구에서는 복합재 샌드위치 적층판의 저속 충격 해석을 수행하였다. 샌드위치 구조 형상의 스킨은 탄소/에폭시(Carbon-Epoxy) 재질이 채택되었고 코어(Core)의 재질은 폼(Foam)이 적용되었다. 연구의 타당성을 입증하기 위해 관련 문헌에서의 연구 결과에서 제시한 실험 결과와 유한 요소 해석 결과의 비교가 선행되었다. 타당성 검증을 바탕으로 본 연구에서 손상이 시작되는 충격체의 속도를 평가하고, 예측된 충격 속도에서 충격 거동을 분석하기위해 유한요소법을 이용하여 충격 해석을 수행하였다. 샌드위치 복합재 적층판의 충격 해석 결과 예측된 충격 속도에서 손상이 발생함을 확인하였다. 최종 시편 시험 결과와 수치 해석 결과의 비교 값이 잘 일치함을 확인하였다.

• 대한기계학회논문집A
• /
• 제34권1호
• /
• pp.1-9
• /
• 2010

본 연구의 목적은 저속충돌에서 승용차량의 범퍼체결구조를 분석하기 위한 것이다. 차량의 손상성-수리성 향상 연구를 위해 범퍼체결구조가 서로 상이한 3개 차종에 대해 RCAR(세계자동차 수리기술위원회)의 저속충돌시험(전,후면 40% 오프셋 충돌시험) 기준을 적용하였다. 시험결과 충격흡수능력은 직사각형 단면형상을 가지고 그 부분이 범퍼레일에 삽입되는 크래시박스식의 범퍼스테이가 대부분의 차량에 적용되고 있는 다른 두 유형의 범퍼체결구조에 비해 우수하게 나타났다. 우수하게 설계된 직사각형 단면형상을 가지는 범퍼체결구조가 저속충돌사고 시 차량의 손상성-수리성을 향상시킴으로써 승객의 안전성도 강화시킬뿐만 아니라 수리비 절감에도 기여할 수 있다는 것이 본 연구에서 입증되었다.

• 한국안전학회지
• /
• 제7권1호
• /
• pp.39-45
• /
• 1992

강구에 의한 횡방향 저속 충격을 받게 되는 복합재의 충격 응력 및 파동 전파에 관한 이론적 및 실험적 연구가 행하여 진다. 이론적 해석을 위해서는 실험적 접촉 법칙과 연계된 Whitney와 Pagano의 이론에 근거한 판 유한 요소 모델이 사용되며, 실험적 해석을 위해서는 직접적인 충격실험이 수행된다. 이러한 해석을 위한 시험편은 ［0/45/0/­45/0］$_{2s}$와 (90/45/90/­45/90)$_{2s}$ 적층 순서를 가지는 유리/에폭시 적층 복합재이며 경계 조건은 clamped-simply support이다. 결과적으로 이러한 두 해석 결과들이 비교 검토되며, 적층 복합재의 충격 응력 및 파동 전파 특성이 규명된다.명된다.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 추계학술대회 논문집
• /
• pp.837-840
• /
• 2002

An analysis method for rubber toughened PVC is suggested to evaluate critical dynamic strain energy release rates($G_c$) from the Charpy impact energy measurements. An instrumented Charpy impact tester was used to extract ancillary information concerning fracture parameters in addition to total fracture energies and maximum critical loads. The dynamic stress intensity factor $K_{Id}$ was computed for varying amounts of rubber contents from the obtained maximum critical loads and also toughening effects were investigated as well. The fracture surfaces produced under low velocity impact fur PVC/MBS composites were investigated by SEM. The results show that MBS rubber is very effective reinforcement material for toughening PVC.C.

• 대한안전경영과학회:학술대회논문집
• /
• 대한안전경영과학회 2004년도 춘계학술대회
• /
• pp.219-231
• /
• 2004

The Charpy and Izod impact tests are the most prevalent techniques used to characterize the effects of high impulse loads on polymeric materials. An analysis method for rubber toughened PVC is suggested to evaluated critical dynamic strain energy release rates(G$_c$) from the Charpy impact tester was used to extract ancillary information concerning fracture parameters in additional to total fracture energies and maximum critical loads. The dynamic stress intensity factor KID was computed for varying amounts of rubber contents from the obtain maximum critical loads and also toughening effects were investigated as well. The fracture surfaces produced under low velocity impact for PVC/MBS composites were investigated by SEM. The results show that MBS rubber is very effective reinforcement material for toughening PVC.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2000년도 추계학술대회논문집A
• /
• pp.250-255
• /
• 2000

Damage induced by low velocity impact loading in aircraft composite laminates is the form of failure which is occurred frequently in aircraft. Low velocity impact can be caused either by maintenance accidents with tool drops or by in-flight impacts with debris. As the consequences of impact loading in composite laminates, matrix cracking, delamination and eventually fiber breakage for higher impact energies can be occurred. Even when no visible impact damage is observed, damage can exist inside of composite laminates and the carrying load of the composite laminates is considerably reduced. The reduction of strength and stiffness by impact loading occurs in compressive loading due to laminate buckling in the delaminated areas. The objective of this study is to determine inside damage of composite laminates by impact loading and to determine residual compressive strength and the damage growth mechanisms of impacted composite laminates. For this purpose a series of impact and compression after impact tests are carried out on composite laminates made of carbon fiber reinforced epoxy resin matrix with lay up pattern of $[({\pm}45)(0/90)_2]s$ and $[({\pm}45)(0)_3(90)(0)_3({\pm}45)]$. UT-C scan is used to determine impact damage characteristics and CAI(Compression After Impact) tests are carried out to evaluate quantitatively reduction of compressive strength by impact loading.

• 한국공작기계학회논문집
• /
• 제10권6호
• /
• pp.48-56
• /
• 2001

In this paper, this study aims at the evaluation on the characteristics of CFRP laminate plates using a falling weight impact tester. The experiment was conducted on several laminates of different orientation. A system was built far measur- ing the impact strength of CFRP laminates in consideration of stress wave propagation theory using a falling weight impact tester. Delamination areas of impacted specimens for the different ply orientation were measured with ultrasonic C- scanner to find correlation between impact energy and delamination area. Absorbed energy of quasi-isotropic specimen having flour interfaces was higher than that of orthotropic laminates with two interfaces. The more interfaces, the greater the energy absorbed. The absorbed energy oft hybrid specimen containing a GFRP layer was higher than that of normal specimens.

• 한국항공우주학회지
• /
• 제33권12호
• /
• pp.39-47
• /
• 2005

본 연구에서는 고속 충격환경을 경험하는 플라스틱 구조 소재에 대한 인장속도별 물성 평가 시험 및 구조건전성 평가에 음향방출 기법을 적용하였다. 인장속도별 물성 평가시험을 통하여 플라스틱 소재 구조물의 건전성 평가에 유용한 음향방출 신호 특성 인자들을 획득하였다. 인장속도에 따른 인장강도는 저속 인장속도 구간에서는 속도가 증가함에 따라 강도가 증가하는 특성을 보여주었으나 일정 속도 영역 이상의 고속 인장시험에서는 인장속도 증가와 무관하게 일정한 강도 값을 나타내었다. 정적 압축 구조시험에서는 음향방출 기법을 적용함으로써 플라스틱 쉘 구조물의 균열발생 시점 및 위치 등을 정확히 평가할 수 있었다.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2001년도 춘계학술발표대회 논문집
• /
• pp.78-82
• /
• 2001

Impact behaviors of Aluminum Honeycombs Sandwich Panel(AHSP) by drop weight test were investigated. Two types of specimens with 1/2" and 1/4" cell size were tested by two impactors which are weight of $5.25\textrm{kg}_{\textrm{f}}$ and $11.9\textrm{kg}_{\textrm{f}}$. Parametric studies were achieved including the impactor weight and impact sites which consist face, long-edge, short-edge, and point of the specimen. Face one of impact sites was the strongest and short-edge one of impact sites was the weakest. The damaged area of AHSP was enlarged with the increase of impactor weight that is equal to impact energy. After 3 point bending test, fracture modes of AHSP were analyzed with AE counts. Lower facesheet was fractured in the long-edge direction and then separated between facesheet and core. In the short-edge direction after core wrinkled, lower facesheet tear occurred. Impact behavior by FE analysis were increased localized damage in fast velocity because the faster velocity of the impact was, the smaller the stress of core was. Consequently, impactor weight had an effect on widely damaged area, while the impact velocity was caused on the localized damaged area.aged area.

• 대한기계학회논문집A
• /
• 제23권11호
• /
• pp.1886-1895
• /
• 1999

The delamination behavior of multidirectional carbon-fiber/epoxy composite laminates under 10NA intermediate and high rates of test, up to rate of about 11.4m s has been investigated using the double cantilever beam specimens. The mode I loading under rates above l.0m/s showed considerable dynamic effects on the load-time curves and thus higher values of the average crack velocity than that expected from a simple proportional relationship with the test rate. The modified beam analysis utilizing only the opening displacement and crack length exhibited an effective means for evaluating the dynamic fracture energy $G_{IC}$. Based on the assumption of constant flexural modulus, values of $G_{IC}$ at the crack initiation and arrest were decreased with an increase of the test rate up to 5.7m/s, but the maximum $G_{IC}$ was increased at 11.4m/s.