• The Journal of Korea Institute of Information, Electronics, and Communication Technology
• /
• v.5 no.3
• /
• pp.117-126
• /
• 2012

This study configuration Vector Control System which is stable and has outstanding Dynamic Characteristics in Very Low Speed Region and Low Speed Region, and proposes Instantaneous Speed Observer and Very Low Speed Control method using Reduced-Dimensional State Observer. The Observer proposed in this system, by appling Reduced-Dimensional State Observer to Load-Torque estimation and using for speed estimation, implements system composition simply and is capable of accurate Instantaneous Speed estimation in Very Low Speed Region. Also, this study reduces influence by System Noise and suggests an induction motor speed control system which is effective in Load Disturbance, modeling error, estimation noise and so on without changing pole of an Observer.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.19 no.4
• /
• pp.376-382
• /
• 2014

This paper proposes the pulse width modulation (PWM) control strategy for low-speed operation in the three-level neutral-point-clamped (NPC) inverters based on the bootstrap gate drive circuit. As a purpose of the cost reduction, several papers have paid attention to the bootstrap circuit applied to the three-level NPC inverter. However, the bootstrap gate driver IC cannot generate the gate signal to the IGBT for low-speed operation, because the bootstrap capacitor voltage decreases under the threshold level. For low-speed operation, the dipolar and partial-dipolar modulations can be the effective solution. However, these modulations have drawbacks in terms of the switching loss and THD. Therefore, this paper proposes the PWM control strategy to operate the inverter at low-speed and to minimize the switching loss and harmonics. The experimental results are presented to verify the validity on the proposed method.

• Proceedings of the KIEE Conference
• /
• 2005.07b
• /
• pp.1077-1079
• /
• 2005

최근 산업기기의 대형화로 인하여 전기기기 및 전력기기의 고효율 대용량 설계에 대한 관심이 커지고 있다. 그 동안에는 대용량 전동기로 주로 유도전동기와 릴럭턴스 전동기가 사용되어 왔다. 그러나 유도전동기는 저속에서의 효율이 낮으며 회전자의 열손실이 효율과 역률을 저하시키는 단점이 있고, 릴럭턴스 전동기는 구조 및 동작원리 상 큰 맥동토크로 인하여 소음과 진동이 매우 크다. 이에 효율과 역률이 좋고 고속운전이 가능한 영구자석형 전동기에 대한 연구가 많이 진행되었고 최근에는 영구자석 재질(희토류계)의 발달함로 인하여 고속 대용량 자석계자형 BLDC와 영구자석형 동기전동기의 설계가 가능해져 대형기에 많이 이용되고 있다. 그러나 대용량 전기기기의 경우 그 크기와 부피가 매우 크고 대전류 대전압의 전원을 공급하여야 하기 때문에 인버터부를 병렬 연결하여야 하므로 제어부를 포함한 전동기의 설치 공간이 증가해 지는 단점이 있다. 이에 본 연구에서는 인버터를 전동기의 회전자 내부에 배치한 인버터 내부형 5[MW]급 BLDC 전동기를 설계하고자 하였다.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.14 no.2
• /
• pp.592-597
• /
• 2013

The heat generated at the motor and inverter inside the electric compressor of inverter built-in type is mainly cooled by refrigerant and generally, there is not a thermal problem. However, the close relation of heat transfer from the motor and inverter parts to the compression part affects on compressor efficiency. Also, according to the surrounding environment and system operation condition, the increased temperature of the motor and inverter can affect the power density of the motor system, and especially, the inverter may be prevented to operate by the temperature limits. In this study, we performed thermo-flow analysis of electric compressor motor system, and investigated the heat dissipation enhancement of the motor and inverter. The motor part in the operation region of the electric compressor was generally maintained at low temperature and the inverter part at high compressor speed was lower temperature than the temperature limit of $85^{\circ}C$. However, the case of the inverter at low speed harsh condition was in excess of $10^{\circ}C$. Therefore, in order to solve the thermal problem, the heat reduction technology of the motor and inverter is essential as well as the improvement of flow path in the compressor.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.15 no.2
• /
• pp.85-94
• /
• 2016

Lane Designation is defined as reasonable road management to ensure the road safety and enhance road efficiency. While the lane designation system was abolished in 1999, it was redefined because of the increasing number of large vehicles in the passing lane, violent on driving and traffic accidents in 2000. The needs of improvement on operating the lane designation has been increasing more in recent due to the low ratio of compliance with the system and difficulties to keep the right lane due to need of turning and demand of widening of designates lane for two-wheeled vehicles and truck. In this study, we presented the improvement plan through the question survey, simulation analysis, safety evaluation. It found a problem that the low-speed vehicle is to use the upper level roadway, difficulties of supervision, the imbalance in the lane use, imbalance traffic and does not match the international standards. This study suggested five different alternatives through the survey. micro simulation has used in order to examine each alternative by management effectiveness and feasibility. It analyzed the traffic speed, efficiency, traffic balance of alternatives. Also, safety evaluation conducted in terms of the range of field-of-view to ensure the easiness of field of view by various configurational difference between the vehicles. By the analysis results of such indicators, This study presents proposals for improvement in operating designated lane that low-speed-big-sized vehicles keep to the right lane, and high-speed-small sized vehicles keep to the left lane.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.40 no.1
• /
• pp.97-102
• /
• 2016

Since vibrations in rotating machinery is a direct cause of performance degradation and failures, it is very important to predict the level of vibrations as well as have a method to lower the vibrations to an acceptable level. However, the changes in balancing during installation and the vibrational modes of the support structure are difficult to predict. This paper presents a method for predicting the unbalanced response of a turbo-compressor supported by active magnetic bearings (AMBs). Transfer functions of the rotor are obtained through system identification using AMBs. These transfer functions contain not only the dynamics of the rotor but also the vibrational modes of the support structure. Using these transfer functions, the unbalanced response is calculated and compared with the run-up data obtained from a compressor prototype. The predictions revealed the effects of the support structure, validating the efficacy of the method.

• Journal of Advanced Marine Engineering and Technology
• /
• v.40 no.3
• /
• pp.217-222
• /
• 2016

This study investigates the design, analysis, and implementation of the square-root extended Kalman filter by using an algorithm derived by combining the Potter or Carlson algorithm with the modified Gram-Schmidt algorithm, for sensorless speed control of a permanent-magnet synchronous motor. The sensitivity of the Kalman filter to round-off errors is a well-known problem. A possible way to address this limitation is by combining the square-root concept and Kalman filter that can improve the numerical performance and solve instability-related problems such as divergence. This paper presents the design and analysis of the implementation of such a square-root extended Kalman filter. To demonstrate the performance of the proposed filter, experimental results under several operating conditions, such as high and low speeds, reversal rotation, detuned parameters and load test, have been analyzed. Further, code sizes and operation times have been compared. Experimental results establish the performance of the proposed square-root extended Kalman filter-based estimation technique for sensorless speed control of a permanent-magnet synchronous motor.

• Proceedings of KOSOMES biannual meeting
• /
• 2006.05a
• /
• pp.207-212
• /
• 2006

The noise levels on board ship recognized at Europe in the early 1970s and the noise regulations on board ship began to put in a statutory form. After that, in 1982 "International Code on Noise Levels on Board Ships" adopted by IMO and it became standard to the newly built ship and remain so to this day. Especially, the ship engine room, which have huge main engine and various kinds of subsidiary machines, is under an extremely loud condition and so the worker who works in it is easy to lose his hearing. Recently, each nation regulates the allowable noise exposure time by law to protect the industrial employee from the occupational hardness of hearing. In our country, the allowable noise exposure time is regulated by the labor standard law but the international provisions regulated by IMO have been applied in case of the ship engine room. In this paper, the cabin's noise levels of cargo-passenger ships plies south-west coast line were investigated.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.9 no.6
• /
• pp.612-619
• /
• 2004

Servo motor systems with ball-screw and timing-belt are widely used in NC, robot, FA and industrial applications. However, the nonlinear friction torque and damping effect in machine elements reduce the control performance. Especially tracking errors in trajectory control and very low velocity control range are serious due to the break-away friction and Stribeck effects. In this paper, a new double speed controller is proposed for compensation of the nonlinear friction torque. The proposed double speed controller has outer speed controller and inner friction torque compensator. The proposed friction torque compensator compensates the nonlinear friction torque with actual speed and speed error information. Due to the actual information for friction torque compensator without parameters and mathematical model of motor, proposed compensator is very simple structure and the stability is very high. The proposed compensator is verified by simulation and experimental results.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.40 no.11
• /
• pp.940-947
• /
• 2012

The target system is a middle size UAV, which is a low-speed long-endurance UAV with a weight of 18 kg and wingspan of 6.4 m. Three electric power sources, i.e. solar cells, a fuel cell, and a battery, are considered. The optimal takeoff time is determined to maximize the endurance because the generated solar cell's energy is heavily dependent on it. Each power source is modeled in Matlab/Simulink, and the component models are verified with the component test data. The component models are integrated into a power system which is used for power simulations. When takeoff time is at 6 pm and 2 am, it can supply the power during 37.5 hrs and 27.6 hrs, respectively. In addition, the thermostat control simulation for fuel cell demonstrates that it yields more power supply and efficient power distribution.