• Journal of Energy Engineering
• /
• v.24 no.3
• /
• pp.48-54
• /
• 2015

In a centralized cooling plant, precise mechanical design and control strategy are required for peak and partial cooling load management. Otherwise, it will lead to low efficiency of cooling system and energy loss due to low partial load efficiency. The purpose of this paper is to enhance energy performance of the centralized cooling plant by controlling flow system in an industrial building using measured data and energy performance simulation program. The simulation results show that the proposed flow control can cut down annual electric power consumption by about 17% compared with the conventional cooling system.

• The KIPS Transactions:PartA
• /
• v.10A no.1
• /
• pp.49-58
• /
• 2003

In a sender-initiated load balancing algorithm, a sender (overloaded processor) continues to send unnecessary request messages for load transfer until a receiver (underloaded processor) is found while the system load is heavy. Therefore, it yields many problems such as low cpu utilization and system throughput because of inefficient inter-processor communications until the sender receives an accept message from the receiver in this environment. This paper presents an approach based on genetic algorithm (GA) for dynamic load balancing in heterogeneous distributed systems. In this scheme the processors to which the requests are sent off are determined by the proposed GA to decrease unnecessary request messages.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.18 no.4
• /
• pp.927-933
• /
• 2014

Ship Power Management System(SPMS) based on Communication Network(CN) is one of the most significant factor for a safe voyage. Therefore, most of the vessels are using greater capacity generator than necessary to prevent pulsating load for safety purposes. However, It provokes low-load damage and reduces generator efficiency that using large capacity generator. Accordingly, in this paper propose hybrid power system for prevent damage of pulse load. Simulation using NI's LabVIEW was conducted for the design of the power system based on actual navigation data of the ship. Also, propose applying methods for hybrid power system in connection with the auxiliary power system for safe navigation.

• Journal of Chest Surgery
• /
• v.35 no.2
• /
• pp.157-160
• /
• 2002

Recently, video-assisted surgical approaches for achalasia have been adopted by many surgeons. Many reports showed that the minimal invasive video-assisted operations for Ihe achalasia revealed such good results as the conventional operations via thoracotomy. In some studies, among the minimal invasive video assisted surgeries for achalasia, the laparascopic assisted operations have some advantages mainly in respect to patient satisfaction over the thoracoscopic assisted surgeries. In this case, the patient had not responded to repeated balloon dilatation, and we made 5 small incisions over the abdominal wall and performed an esophageal myotomy and partial anterior fundoplication by laparascopic guide. The patient's symptoms were almost relieved, and the postoperative radiologic findings were satisfactory.

• Journal of the korean Society of Automotive Engineers
• /
• v.9 no.2
• /
• pp.1-4
• /
• 1987

내연기관 연구에 전념하는 모든 사람들의 한결같은 3대 염원은 연비향상, 비출력증대 및 유해 배기가스 성분 감소이다. 이중 비과급 가솔린 기관의 경우 비출력 증대를 위한 4-stroke cycle 엔진에서의 여구는 현지까지 헤아릴 수 없이 많은 연구가 진행되어 발전의 한계에 도달한 느낌 이다. 따라서 이의 실질적인 증대는 시각을 달리하여 2-stroke cycle로의 전환으로서만 가능하리 라 본다. 2-stroke 엔진은 원래 이목적으로 고안된 것이라는 것은 주지의 사실이다. 그러나 이 장치가 비출력면에서 효과적인 가솔린엔진의 경우에서도 현재까지 별로 각광을 받지 못한 것은 다음과 같은 몇가지 두드러진 이유 때문이라고 본다. 첫째 흡입연료의 일부가 소기(scavenging) 과정에서 배기공으로 곧바로 유출됨으로 배기 공해성분을 증가시키고 연료손실에 따른 연비저감 을 초래하는 것이다. 둘째로 crankcase 소기를 이용하는 소형가솔린 2-stroke 엔진에서는 새 공 기의 흡입이 충분치 못하여 일방적으로 높지 않은 소기효율을 고려한 최종 흡입 체적효율은 상당 히 낮아지게 됨으로써 목적하는바의 비출력 증대의 득을 별로 얻지 못함은 물론 잔류가스율이 높아 저부하, 저속도에서 엔진의 구동이 손조롭지 못ㅎ하고 시동이 어려워지는 특성을 나타나게 된다. 따라서 이러한 바람직하지 못한 결과를 감수할 수 있는 경우에는 소형원동기에 주로 2-stroke 가솔린 엔진이 이용되어 왔다. 요사이 이러한 약점들을 타개할 수 있는 고안들이 미국 SAE지에 소개되어 관심을 끌고 있어 이에 대해 요저먹으로 소개하고자 한다.

• Journal of Power System Engineering
• /
• v.11 no.1
• /
• pp.5-15
• /
• 2007

In the recently released accident-investigation report on blade failure, almost 70% of blade failures was found at low pressure turbine blades, and it is well known that main cause is due to the vibration modes. This paper describes the systematic approach on the root cause of the blade failure at L 0 stage, 30MW single flow industrial steam turbine which had tripped by high vibration after ten-month commercial operation. A fracture was found at the only one damping wire hole of 59 blades, and crack was detected at three damping wire holes by NDT. According to the analysis result for the crack fracture surface and the chain of the sequential operational events, we come to the conclusion that a typical high cycle fatigue is the most dominant factor caused to the blade failure, the resonance frequency margin was narrowed by the cut damping wire and the high cycle vibration was amplified, and then the blade was broken at once by the centrifugal force when the crack reached the critical size.

• Journal of the Korean GEO-environmental Society
• /
• v.18 no.11
• /
• pp.19-26
• /
• 2017

When narrowly excavated in the urban area, the wall of backfill space is not only symmetrical but also asymmetrical. In this case, the horizontal stress induced by backfilling depends mostly on the wall asymmetry and the wall friction angle. Therefore, in this study, the model test in the laboratory was conducted to investigate horizontal earth pressure with depth considering various boundary conditions such as base width, wall friction, relative density of backfill, and wall angle. As the wall is smoother and wall angle is lower from the bottom, the results showed higher the horizontal stresses due to the increase of vertical stresses.

• Clean Technology
• /
• v.2 no.2
• /
• pp.165-175
• /
• 1996

Cutting fluids in machining process are one of the parameters which have serious effects on the environment. A simple method to accomplish the environmentally clean process is to evaluate the effects of cutting fluids and select one which has the least environmental load. In this research, a process planning to select the best cutting fluid is suggested considering both machinability and environmental effects. The selection criteria and evaluation method named AHP are introduced. The planning process is illustrated with drilling characterized as a heavy-duty and low-speed process. Five standard fluids are compared with respect to five environmental attributes. Compounded cutting oils are superior to water-soluble oils in both machinability and environmental effects.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.28 no.4B
• /
• pp.361-368
• /
• 2003

An SNMP manager requests a value in MIB of a designated object to an agent by management policy defined in the SNMP, and then the agent responds to this manager. So, it causes a lot of networks traffic between them, Specially, repetitious occurrence of sending-receiving information related to the same object is very inefficient when the trend analysis of traffic is performed. In this paper, an efficient SNMP is proposed to add new PDUs to the existing SNMP in order to accept time function. Utilizing this PDU, it minimizes unnecessary sending-receiving information and collects information on trend management appropriately. The implemented SNMP is tested for compatibility with the existing SNMP and decreases the amount of network traffic greatly.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.22 no.12
• /
• pp.2635-2643
• /
• 1997

In this paepr, a routing algorithm is proposed in order to reduce average end-to-end delay and congesting in the high speed network. The algorithm proposed here uses the existing one which adaptively modifies routes and the amount of traffic allocated to each link as user traffic partterns flutuate. This algorithm is ELB(Equitable Load Balancing). Also, the new algorithm considers the proportional to the distance between source and destination. It reduces congestion from the ELB and average end-to-end delay from the propagation dealy concepts respectively. Through the simulation, it shows that the algorithm proposed here reduces average end-to-end delay over low load to high load, and it also guarantees the congestion control.