• The Journal of the Korea Contents Association
• /
• v.6 no.4
• /
• pp.1-10
• /
• 2006

In this paper, a broadband RF module is designed and tested for 2.4GHz band applications. The RF module is composed of a low noise amplifier (LNA) with a three stage amplifier, a single ended gate mixer, matching circuits, a hairpin line band pass filter and a Chebyshev low pass filter to convert the radio frequency (RF) into the intermediate frequency (IF). The LNA has a high gain and stability, and the single ended gate mixer has a high conversion gain and wide dynamic range. In the analysis of the broadband RF module, the composite harmonic balance technique is used to analyze the operating characteristics of an RF module circuit. The RF module has a 55.2dB conversion gain with a 1.54dB low noise figure, $-120{\sim}-60dBm$ wide RF power dynamic range, -60dBm low harmonic spectrum and a good isolation factor among the RF, IF, and local oscillator (LO) ports.

• Proceedings of the KIEE Conference
• /
• 2002.07c
• /
• pp.1527-1529
• /
• 2002

본 논문은 저손실 소형 대역통과 여파기인 기지국용 RF/Microwave 수동소자의 다중 공진 모드(Multi-Mode)에 관한 연구로 한개의 유전체 공진기(Dielectric Resonator)로 두개의 공진 모드(Dual-Mode)를 형성하고 그의 결합량을 조절하여 대역통과 여파기를 설계 및 제작하고, 기지국용 Dual-Mode 대역통과 여파기의 소형화, 경량화를 50%이상 향상시켜 양질의 Dual-Mode 공진 특성을 관찰하였다.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.19 no.7
• /
• pp.26-31
• /
• 2005

In this paper, a small BPF(band pass filter) is designed using new probe type for wireless communication system. The dielectric resonator is used high Q ceramics for low loss characteristic. In order to provide a band pass filter which can be reduced in dimension, can be reduced in height, and can be surface-mounted. The filter was fabricated using $TE_{01{\delta}}$ mode dielectric resonator. The input/output probes are attached to coner portion of the rectangular metal cavity. Results of the manufactured filter($12{\times}12{\times}8[mm]$) show that the center frequency is 9.95358[GHz], the insertion loss is -1.9[dB], the 3[dB]_bandwidth is 14.9[MHz], and the loaf Q is 664.

• Journal of the Institute of Electronics Engineers of Korea SC
• /
• v.42 no.5 s.305
• /
• pp.43-50
• /
• 2005

This paper describes some IC(integrated circuits) design and implementation techniques of low power multi-band Gm-C bandpass filter for body composition analyzer. Proposed BPF(bandpass filter) can be selected from three bands(20 KHz, 50 KHz, 100 KHz) by control signal. To minimize die area, a simple center frequency tuning scheme is used. And to reduce power consumption, operational transconductance amplifier operated in the sub-threshold region is adopted. The proposed BPF is implemented with 0.35 um 2-poly 3-metal standard CMOS technology Chip area is $626.42um\;{\times}\;475.8um$ and power consumption is 700 nW@100 KHz.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.2
• /
• pp.200-207
• /
• 2009

This paper presents a compact, low insertion loss, sharp rejection and wide band microstrip band pass filter that is composed rectangular loop resonator and Step-Impedance-Open-Stub(SIOS). The SIOS can be reduce length about 30 % more than general 0.25 $\lambda$ open stub. And the stub can the advantage of tuning impedance magnitude. In order to demonstrate agrement of this paper prove, the optimized wide band pass filters are realized and experimented. A transmission line model used to calculate the frequency response of the new filters shows good agreement with measurements. The filter has 3 dB fractional bandwidth of 51.75 %(3.206 GHz), an insertion loss of better than 0.44 dB from 4.587 GHz to 7.793 GHz, and two rejection of greater than 30 dB within 221 MHz($4.326{\sim}4.587\;GHz$) at low frequency band, 181 MHz($7.739{\sim}7.954\;GHz$) at high frequency band. Maximum rejection characteristics of the filter are -61.8 dB at low frequency and -76.3 dB at high frequency.

• Proceedings of the KIEE Conference
• /
• 2001.11a
• /
• pp.35-37
• /
• 2001

다층 인쇄 회로 기판에 Combline 구조를 가진 스트립 라인 또는 마이크로 스트립 라인 대역통과 필터를 구현하였다. 저 비용 구현과 이동성과 휴대성을 강조하기 위해 기존의 세라믹 대신 FR4 와 에폭시를 기반으로 하는 다층 회로 기판의 도체 층에 집적화하였다. Combline 각 끝단에 커패시터를 부하 함으로써 전기적 길이를 화장하였고 전체적인 크기를 감소시킴으로서 적당한 필터 특성을 얻을 수 있었다. 구현된 필터는 마이크로파 대역에서 사용 가능하며 특히 Bluetooth나 Wireless LAN 과 같은 ISM 대역을 사용하는 무선통신소자로서 사용 가능하다.

• Journal of IKEEE
• /
• v.12 no.4
• /
• pp.225-233
• /
• 2008

This paper presents a compact, low insertion loss, sharp rejection and wide band microstrip band pass filter that is composed rectangular loop resonator and step-impedance-open-stub(SIOS) for wireless data communication. The SIOS can be reduce length about 30% more than general 0.25${\lambda}$ stub. And stubs can have the advantage of tuning impedance magnitude. In order to demonstrate agrement of this paper prove, the optimized wide band pass filters are realized and experimented. A transmission line model used to calculate the frequency response of the new filters shows good agreement with measurements. The filter with perturbation stubs has four poles at rejection band, the poles are excited 3.610GHz, 4.265GHz at low frequency band, 8.494GHz, 9.056GHz at high frequency band. And the filter has 3dB fractional bandwidth of 57%(3.695GHz), an insertion loss of better than 0.37dB from 4.549GHz to 8.244GHz, and two rejection of greater than 30dB within 237MHz(4.312GHz${\sim}$ 4.549GHz) at low frequency band, 234MHz(8.244GHz-8.491GHz) at high frequency band.

• 전자공학회논문지 IE
• /
• v.47 no.2
• /
• pp.60-65
• /
• 2010

In this paper, we propose a dual-band filtering method optimized to DBO-CSS systems which are alternatively transmitted in low and high bands. The conventional channel filter which passes entire signal bandwidth causes a problem that excessive noise in neighboring sub-band is added while one of signals in two sub-bands is received. The dual-band filtering proposed in this paper can overcome the performance degradation in the conventional filtering method without increase of hardware complexity. The proposed method is based on two filters to be matched with DBO-CSS signals receiving alternatively and can exclude the undesired noise in neighboring sub-band. Simulation results for the proposed method show better performance about 2.5dB than the conventional one.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.17 no.3
• /
• pp.678-684
• /
• 2013

This paper describes a low-power baseband circuit for SAW-less LTE-Advanced transmitters. The proposed transmitter baseband circuit consists of a 2nd-order Tow-Thomas type active RC-LPF and a 1st-order passive RC LPF. It can provide a 7 multi-channel cut-off frequencies and wide gain control range of -41 dB ~ 0 dB with a 1-dB step. The proposed 2nd-order active RC-LPF adopts an op-amp in which three other sub-op amps are in parallel connected to reduce DC current for different cutoff frequency. In addition, each sub-op amp adopts both Miller and feed-forward phase compensation method to achieve an UGBW of more than 1-GHz with a small DC power consumption. The proposed baseband circuit is implemented in 65-nm CMOS technology, consuming DC power from 6.3 mW to 24.1 mW from a 1.2V supply voltage for each different cut-off frequency.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.20 no.4
• /
• pp.323-332
• /
• 2009

In this paper, we introduce a modified short-circuited stub bandpass filter suitable for ultra-wideband(UWB) applications utilizing low temperature co-fired ceramic(LTCC) technology. By modifying the conventional short-circuited stub bandpass filter structure with stubs and connecting lines of lower characteristic impedances, the number of stubs has been reduced from 5 to 2 on a high dielectric constant substrate($\varepsilon_r$ = 40). A wireless local area network (WLAN) stopband in the frequency range of 5.15 to 5.825 GHz has been inserted into the filter characteristic using three short-circuited coupled lines. The filter has been measured with an insertion loss less than 1.0 dB and return loss better than 10 dB in the pass bands. A bandwidth ratio of 109.49 % has been achieved. Measurement results agree well with simulation results. The dimensions of the filter are $4{\times}8{\times}0.57\;mm^3$.