• Journal of the Earthquake Engineering Society of Korea
• /
• v.6 no.4
• /
• pp.39-49
• /
• 2002

In this paper, the characteristics of RB(rubber bearing) were studied by various prototype tests on RB with low hardness rubber. The characteristics of RB were tested on displacements, repeated cycles, frequencies, vertical pressures, temperature, vertical stiffness and the capability of shear deformation. The prototype test showed that the displacement and vertical pressures were the most governing factors influencing on characteristics of RB. The effective stiffness and equivalent damping of RB showed small increment in high frequency range. After the repeated cyclic test with 50's cycles, the effective stiffness and equivalent damping of RB were almost constant compared with those of the 1st cycles due to low hysteretic damping. The shear modulus of RB was reduced after large deformation, and this value of RB was partly recovered after 40 days. Finally, the shear failure test of RB was conducted, the prototype was failed over 490% of shear strain, and real size RB was failed over 430% of shear strain.

• Journal of Adhesion and Interface
• /
• v.3 no.3
• /
• pp.1-6
• /
• 2002

We invested which is major one in rubber materials design factors affecting on noise and showed the design guide for low noise tire development in this study. Tire noise and impact noise for rubber sheets were tested at anechoic room. Hardness, tensile and dynamic mechanical properties were also measured using the rubber sheets. A major design factor of rubber materials affecting on the tire noise was hardness or 300% modulus. There was also positive correlation between two properties. Therefore, designing rubber materials to have low hardness or 300% modulus can reduce noise.

• Journal of the Earthquake Engineering Society of Korea
• /
• v.12 no.3
• /
• pp.11-20
• /
• 2008

In this paper, the characteristics of low hardness high damping rubber bearings(HDRB) were studied through various prototype tests. The low hardness HDRB were tested to evaluate vertical stiffness, shear stiffness, equivalent damping ratio, various dependencies of shear properties, ultimate shear properties and other factors. The prototype test was performed according to the specifications of ISO 22762-1, and evaluated according to the specifications of ISO 22762-3. The results of the prototype test showed that shear strain and temperature were the factors that most greatly influenced shear stiffness, and that compressive stress was the factor that most greatly influenced the equivalent damping ratio. The frequency dependence test of shear properties showed that two general tendencies of frequency dependence could be observed. At frequencies over 0.1Hz, the changes in shear properties were small. However, at frequencies under 0.1Hz, the changes in shear properties rapidly decreased. The creep test and the ultimate shear test were also performed, and both of them satisfied the requirements of ISO 22762-3.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2017.05a
• /
• pp.160-162
• /
• 2017

When rubber elastomer has contact with fuel, since the component and additive having low molecular weight can flow out, the physical properties of both elastomer and fuel could be hindered. In order to predict the life of the rubber elastomer, this study is to determine the change of weight, thickness, hardness, strain, and compression set as mechanical properties of the sealant rubber O-ring, which was dependent on volume, temperature, and storage time of the contacted fuel. We also determined purity of fuel via GC analysis and measured gross heat of combution. The results could be used as a reference to evaluate the life of the rubber elastomer.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.25 no.6
• /
• pp.533-540
• /
• 2012

Rubber laminated bearings with lead core are highly affected by changes in temperature because key materials which are rubber and lead have temperature dependencies. In this study, two full scale LRB(D800, S=5) are manufactured and temperature dependency tests on shear properties are accomplished. The shear properties at the 3rd cycle are used at $-10^{\circ}C$, $0^{\circ}C$, $10^{\circ}C$, $20^{\circ}C$, $30^{\circ}C$, $40^{\circ}C$ respectively. The double shear configuration, simultaneously testing two pieces, is applied for compression shear test in order to minimize the friction effects due to the test machine, described in ISO 22762-1:2010. Characteristic strength, post-yield stiffness, effective stiffness, equivalent damping ratio are estimated and presented coefficient due to the temperature changes.

• Elastomers and Composites
• /
• v.34 no.2
• /
• pp.121-127
• /
• 1999

Characteristics of high molecular weight styrene-butadiene rubber(HM-SBR)/low molecular weight styrene-butadiene rubber(LM-SBR) mixtures were studied to investigate how to modify the processability and the mechanical properties of styrene-butadiene rubber (SBR). Mooney viscosity of the HM-SBR/LM-SBR mixtures and torque increase due to the vulcanization decreased by increasing the LM-SBR content of the mixtures. Shore A hardness and rebound properties were decreased by increasing the LM-SBR content of the mixtures. It was found that the value of tan ${\delta}$ of the mixtures in rubbery state was increased, while glass transition temperatures of the vulcanized blends were constant by increasing the LM-SBR content of the mixtures. It was postulated that the decrease of Mooney viscosity by increasing the LM-SBR content of the blends was due to plasticizing effects of the LM-SBR and the increased polydispersity of the mixtures. Change of mechanical properties of the vulcanized HM-SBR/LM-SBR mixtures was attributed to the decreased crosslink densities of the mixtures by increasing the LM-SBR content of the mixtures.

• Journal of the Society of Cosmetic Scientists of Korea
• /
• v.43 no.1
• /
• pp.27-33
• /
• 2017

Up to now, better convenience and portability were important factors in the development of the cosmetics and achieved by immersing low viscosity makeup water-in-oil (W/O) emulsion into the impregnation material. Conventionally, polyurethane sponges having porous network structures and hard textures have been dominantly used. It has an advantage of easy to manufacture because of its good impregnation property due to its structural characteristics. However, it releases emulsion too much at first use, and shows unexpected dramatic decline during the period of usage. In this study, we studied on makeup W/O emulsion with various features and developed the new foaming sponge, which showed excellent formability and proper absorption and discharge ability of cosmetic composition through the combination of natural rubber (NR) and styrene butadiene rubber (SBR). This impregnation material is characterized by the softness of elasticity like a rubber, high elongation and uniform output. We confirmed that this material can be used to develop makeup products using various oils depending on polarity and controlling the viscosity of the makeup W/O emulsion. Thus, it is concluded that these results provide valuable information in developing new cosmetics impregnation materials.