• Elastomers and Composites
• /
• v.46 no.4
• /
• pp.318-323
• /
• 2011

To recycle the waste tire rubber powder, rubber powder composite for waterproof sheet was prepared, and analyzed the effect of the kind of resin and the amount of crosslinking agent on the mechanical property of the composites. The elongation-at-break of the PE composite increased more than 3 times as EPDM was added into rubber composites. As the content of the crosslinking agent increased, the tensile strength of composite increased as well. When recycled polypropylene was used, the increase in composite's tensile strength was more than 3 times. Therefore to use the recycled PP in composite is more effective rather than PP in term mechanical properties.

• Journal of the Korean Wood Science and Technology
• /
• v.33 no.6 s.134
• /
• pp.46-54
• /
• 2005

To make the composite panels of wood particles and recycled plastics, the recycled polypropylene was used. In the composite panels the sizes of wood particles were 1/32", 1/4" and 1/2" mesh, and the composition ratios of the recycled plastics were 10%, 30%, 50% and 70%. The physical and mechanical properties of the composite panels were investigated. As the composition ratio of wood particle increases, the density increases, while it decreases at the same composition ratio because the size of wood particle increases. As the composition ratio of recycled polypropylene increases from 10% to 30%, both thickness swelling and water adsorption significantly decrease. As the composition ratio of recycled polypropylene increases, the modulus of rupture in bending strength increases, but the modulus of elasticity in bending strength decreases. SEM shows that the dissolved recycled polypropylene penetrates into tracheid and pit, and bonds mechanically to other wood particle and matrix to increase the bonding strength and improve the physical and mechanical properties of composite panel.

• Resources Recycling
• /
• v.24 no.2
• /
• pp.36-45
• /
• 2015

In this study, various sizes of waste ground rubber tire (WGRT) were devulcanized by a single screw extruder equipped with a sonicator in front of the die, and waste PP and devulcanized waste ground rubber tire (DWGRT) composites were prepared by an intermeshing co-rotating twin screw extruder. The crosslink density and percent devulcanization of WGRT and DWGRT for 40, 80 and 140 meshes were calculated. The mechanical properties of the composites were compared with each other. The effect of SEBS-g-MA as a compatibilizer was investigated on mechanical properties of both waste PP/WGRT and waste PP/DWGRT composites. The crosslink density was decreased with decreasing the WGRT size. On the other hand, the percent devulcanization was increased by adding the smaller size of WGRT. Also, tensile strength, impact strength and elongation at break of the composite with DWGRT were higher than those with WGRT. Especially, mechanical properties of the composites were significantly increased by adding the smaller size of WGRT and DWGRT. Addition of SEBS-g-MA into both waste PP/(D)WGRT composites exhibited better impact strength and elongation at break than the composites themselves.

• 한국신재생에너지학회:학술대회논문집
• /
• 2005.11a
• /
• pp.405-413
• /
• 2005

본 연구에서는 3톤/일의 플라스틱 투입량을 기준으로 혼합폐플라스틱으로부터 대체연료유를 생산할 수 있는 소용량 중심의 폐플라스틱 유화설비를 설계 제작하였으며 장기간에 걸친 시운전을 통하여 유화설비의 운전성 평가에 대한 실증연구를 수행하였다. 대상 폐플라스틱으로는 플라스틱 재활용 업체에서 분리 선별된 폴리에틸렌과 폴리프로필렌 그리고 이들을 혼합한 폐플라스틱을 각각 적용하였으며 $400\sim420^{\circ}C$의 분해 운전온도에서 폐플라스틱의 종류에 따른 시운전 평가를 하였다. 본 실증연구로부터 폴리에틸렌의 경우에 있어서는 79%의 재생유 회수율을 그리고 폴리프로필렌의 경우에 있어서는 80%의 재생유 회수율을 각각 얻을 수 있었으며 플라스틱 종류별 안정적인 운전조건을 확보할 수 있었다. 또한 폐플라스틱 투입량에 대한 설계용량과 운전용량과의 비교로부터 약 40$\sim$50%의 설계오차가 발생한 것으로 평가되었으며 이는 유화설비의 설계를 위하여 사용된 혼합폐플라스틱의 부정확한 물성 값에 기인한 것으로 판단된다. 따라서 본 연구로부터 얻은 시운전결과를 바탕으로 설계인자들을 확립하는 과정이 반드시 필요할 것으로 판단된다.

• Journal of the Korea Concrete Institute
• /
• v.19 no.3
• /
• pp.333-339
• /
• 2007

The purpose of this study was to enhance bond performance between recycled PET (polyethylene telephthalat) fiber and cement composites through hydrophilic treatment using maleic anhydride grafted polypropylene(mPP). The mPP with various concentration of 0%, 5%, 10%, 15% and 20% to determine effect on bond behavior of recycled PET fiber were applied as experimental variables. Dog bone shaped specimens according to JCI SF-8 was applied to evaluate the bond strength and pullout energy. The results showed increased bond strength and pullout energy as concentration of mPP. Concentration of 15% mPP showed the most effective results while 20% showed reduced performance results. Because 15% mPP ensures perfect coating while 20% makes thick coating area that resulted in crack propagation and consequent separation of PET fiber and coated area during pullout load occurred. Enhancement mechanism of bond performance of recycled PET fiber and cement composites with each concentration of mPP could be conformed through investigation of microstructure of fiber surface.

• Resources Recycling
• /
• v.23 no.1
• /
• pp.70-79
• /
• 2014

In this study, waste polypropylene and waste ground rubber tire(WGRT) composites were prepared by using a modular intermeshing co-rotating twin screw extruder. The effect of three main factors such as WGRT contents, particle size, compatibilizers on the properties of waste PP/WGRT composites was extensively investigated. Tensile strength of the composites was decreased with an increase in WGRT contents, whereas elongation at break and impact strength were increased. The tensile strength, elongation at break and impact strength of the composites with the smaller size of the WGRT were more enhanced. Addition of PP-g-MA into waste PP/WGRT composites exhibited better tensile strength. However, elongation at break and impact strength were slightly decreased with increasing of PP-g-MA. On the other hand, tensile strength, impact strength and elongation at break of the composites were increased by adding the EPDM-g-MA and SEBS-g-MA. Especially, elongation at break was significantly increased compared to the composite with PP-g-MA.

• Polymer(Korea)
• /
• v.24 no.6
• /
• pp.777-786
• /
• 2000

Fire resistance and thermal stability of polypropylene composite systems were investigated by using several halogenated fire-retardants such as decabromodiphenyl oxide (DBDPO) and chlorinated paraffin wax (CPW). The fire resistance of composite systems was thoroughly examined by measuring limited oxygen index (LOI, ASTM D2863, ISO 4589) and characteristic properties of cone calorimetry(ASTM E1354, ISO 5660) heat release rates (HRR), time to ignition (TTI), total heat release (THR), effective heat of combustion (EHC), mass loss rates, etc. Comparing the cone calorimetry experimental results of the halogen flame retardants, DBDPO exhibited twice higher efficiency than CPW in polypropylene systems, and the LOI also showed similar trends to cone calorimetry. The thermo-oxidative stability of the composite systems was increased about 30-5$0^{\circ}C$ in thermogravimetry analysis.Collectively, the combustion, extinction and thermally-stable characteristics of flame retardants were identified in this study.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.10a
• /
• pp.419-424
• /
• 2000

The primary objectives of this study are to investigate the properties of strength and durability of recycled aggregate concrete was added polypropylene as variables and to fabricate fine concrete in some conditions. The variables are substitution ratios of recycled aggregate(0, 30, 50, 100%) and additions of polypropylene(0, 0.2, 0.5, 1.0%). Compressive strength test to investigate strength properties and freeze-thawing test and drying shrinkage test to durability properties were done. As the result of this study, When variables are substitution ratio(30%) of recycled aggregated and addition(0.5%) of polypropylene, fine concrete was fabricated.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.10a
• /
• pp.655-660
• /
• 2000

This study was performed to verify the properties of concrete used recycled aggregate(0, 30%, 50%). Also, to improve the brittle fracture, energy absorption and apparent ductility of concrete, we added polypropylene fibers(0, 0.1, 0.2, 0.5, 1.0% by volume of concrete). As the experimental results, adding 30% recycled aggregates and 0.5% polypropylene fibers to concrete mixes enhances the properties of both compressive strength and toughness.

• Journal of the Korean Geosynthetics Society
• /
• v.2 no.3
• /
• pp.25-38
• /
• 2003

Geotextile composites to improve the resistance to the application environment were manufactured of recycled polyester geotextile with carbon black as ultraviolet stabilizer and polypropylene geotextile by needle-punching method. Mechanical properties, ultraviolet resistance and chemical stability were evaluated. Retention ratio of tensile properties of polypropylene geotextiles were decreased about 50% with the exposed condition by ultraviolet but those of geotextile composites showed the slightly decrease. Geotextile composites which have larger weights of recycled polyester geotextile were more stable against ultraviolet. For chemical stability, the changes of tensile strength values of geotextile composites were in the range of -20~+10% at the various chemical conditions.