• Journal of the Korea Convergence Society
• /
• v.8 no.7
• /
• pp.123-129
• /
• 2017

Morphological and ultrastructural characteristics of human hair medulla was investigated with scanning electron microscopy and transmission electron microscopy. The medulla is located in the central position of hair shaft and appear greatly variable forms which discontinuous shape arranged from hair root to apical portion according to longitudinal axis. The thickness of medulla from a single hair presented as very variable in size. The diameter of cross section of human hair medulla measured as $21{\mu}m$ and longitudinal section showed $27{\mu}m$. It grows up to 1/3 from 1/4 in diameter of human hair shaft. It appears emptied hole during separating of macrofibrils in the keratinocyte. The empty space measured $6.5{\mu}m$ in diameter as maximum size and it was filled with air.

• 한국지구과학회:학술대회논문집
• /
• 2010.04a
• /
• pp.121-121
• /
• 2010

행성상 성운 NGC 7009와 NGC 7027의 모델을 연구하기 위해 1998년 8월 14일부터 16일 까지 3일간의 Keck I HIRES의 분광 관측 자료를 이용하였다. 사용한 파장 영역은 $3250{\AA}{\sim}8725{\AA}$이고, H I, He I, He II, C II, C III, N II, N III, [N II], [O I], [O II], [O III], [S II], [S III], [Cl III], [Cl IV], [Ar III], [Ne III] 등의 방출선을 얻었다. 본 연구에서는 이러한 방출선의 선윤곽(line profile)을 IRAF와 StarLink/Dipso를 이용해 분석하여 성분을 구하였는데 H I, He I, He II, [O III], [C III], [N II] 등 대부분은 2개로 분리되었고, [S II], [Ar III]의 경우에는 3개로 분리되었다. 후자의 경우 구각(shell)의 단순한 팽창뿐만 아니라 다른 제3의 방향으로 팽창하고 있는 성분이 존재함을 의미한다. 비교적 S/N가 양호한 선들의 FWHM(Full Width at Half Maximum)을 측정하여 팽창속도를 구한 후 이 선들이 생성에 기여한 지역의 온도 또는 이온화 에너지 (IP)에 대한 팽창속도의 변화를 조사하였다. 또한 두 행성상 성운의 물리적 특성과 화학 원소 함량을 결정하기위해 광이온 모델 Tlusty Code와 CLOUDY를 사용하여 NGC 7009의 선행연구 Hyung & Aller(1995), Kwitter & Henry(1998)와 비교하였고, NGC 7027은 Zhang & Liu(2005), Middlemass(1990)와 비교하였다. NGC 7009과 NGC 7027의 수소 밀도($N_H$)를 $8,000cm^{-3}$으로 가정했을 때, NGC 7009의 중심별의 온도는 77,000K이고, 구각(shell)의 크기는 0.031~0.044pc이며 장축에 대해서만 결과를 나타내었다. NGC 7027의 경우, 중심별의 온도는 180,000K이고, 구각(shell)의 크기는 0.015~0.02pc으로 판단된다.

• Journal of the Microelectronics and Packaging Society
• /
• v.26 no.4
• /
• pp.95-100
• /
• 2019

Nanoindentation has been widely used for evaluating mechanical properties of nano-devices, from MEMS to packaging modules. Residual stress is also estimated from indentation tests, especially the Knoop indenter which is used for the determination of residual stress directionality. According to previous researches, the ratio of the two stress conversion factors of Knoop indentation is a constant at approximately 0.34. However, the ratio is supported by insufficient quantitative analyses, and only a few experimental results with indentation depth variation. Hence, a barrier for in-field application exists. In this research, the ratio of two conversion factors with variation in indentation depth using finite elements method has been attempted at. The magnitudes of each conversion factors were computed at uniaxial stress state from the modelled theoretical Knoop indenter and specimen. A model to estimate two stress conversion factor of the long and short axis of Knoop indenter at various indentation depths is proposed and analyzed.

• The Bulletin of The Korean Astronomical Society
• /
• v.36 no.1
• /
• pp.61.1-61.1
• /
• 2011

NGC5929는 북동방향으로 0.5' 떨어진 NGC5930의 기조력 영향을 받는 활동성은하이다. 우리는 NGC5930이 NGC5929와의 상호작용에 따라 NGC5929의 활동성을 어떻게 유발하는지 수치실험을 알아보고자 한다. NGC5929의 적경, 적위는 (15h 26m, $41^{\circ}$40')이고, 크기는 $1'.14{\times}$ 0'.89이다. 지구로부터 거리는 36.5Mpc(적색편이는 $0.00836{\pm}0.00007km/s$)이다. 관측 자료에서 보인 NGC5929는 원반 모양의 은하 오른쪽 위쪽의 가스는 접근성, 왼쪽 아래 부분은 멀어지는 운동학적 특성이 보인다. 호스트 은하 원반이 기울어져 장축 방향이 $PA=85^{\circ}$, 단축이 $PA=45^{\circ}$ 은하의 구조임을 알 수 있다. 이 연구를 위해 우리는 하와이 CFHT 3.6m의 OASIS로 관측한 NGC5929의 중심부를 MR1, MR2로 관측한 영상을 참고하여, 이 영상에서 보이는 활동성 즉, 15*12 arcsec의 OASIS field 영역의 관측 자료에 나타난 $H{\beta}$영상이나, [O III]에 나타난 제트 형태와 방출방향에 대해 조사하였다. CFHT OASIS의 분석으로 우리는 continuum, [O III], $H{\beta}$ 선을 통한 영상을 조사하였고, 특히 [O III]영상에서 에서 강한 활동은하의 성격이 보인다. 이 방출선의 특성이 별의 UV, 행성상 성운 주변, 블랙홀 주위, 충격파 중 어느 영향이 가장 강한지 조사하였고, [O III]이미지에서 보인 제트의 형성조건에 동반은하 NGC5930의 영향이 어떠한 역할을 하였는지 조사하고, $H{\beta}$영상에 나타난 starburs지역도 살펴보고자 한다. 우리는 관측 자료에서 보인 활동성의 근원을 알기 위해 Gadget, Magalie를 사용하여 두 은하의 운동학적 및 은하의 구조에 대해 조사하려고 한다.

• Applied Biological Chemistry
• /
• v.35 no.5
• /
• pp.382-388
• /
• 1992

Mycelial growth inhibition activity of forty-one N-substituted phenyl 5-chloro-1,3-dimethylpyrazole-4-carboxamides against Rhizoctonia solani was analysed quantitatively by multiple regression analysis using physicochemical parameters of substituents as independent variables and $pEC_{50}$ as dependent variable. As a result, a quantitative structure-activity relationship was formulated using eight physicochemical parameters, which explains 83% of variance of the fungicidal activity. The most important parameter for the biological activity was log k', as related to the penetration and transport processes in the biological system. The activity also correlated with other hydrophobic parameters$({\pi}_2,\;{\pi}_3)$, an electronic parameter$({\Sigma}{\sigma})$, and steric parameters$(STERIMOL\;parameters\;L_3,\;L_4)$.

• Tunnel and Underground Space
• /
• v.26 no.6
• /
• pp.493-507
• /
• 2016

Scaled model tests were performed to investigate the stability of a foundation located above limestone cavities. Cavity shape was assumed to be an ellipse having 1/3 for the ratio of minor to major axis lengths. 12 different test models which have various depths, locations, inclinations, sizes and numbers of cavity were experimented and they were classified into 5 different groups. Crack initiation pressure, maximum pressure, deformation behaviors, failure modes and subsidence profiles of test models were obtained, and then the influences of those parameters on the foundation stability were investigated. No cavity model showed a general shear failure, whereas the models including various cavities showed the complicated three different failure modes which were only punching failure, both punching and shear failures, and double shear failure. The stability of foundation was found to be decreased as the cavity was located at shallower depth, the size and number of cavity were increased. Differential settlements appeared when the cavity was located under the biased part of foundation. Furthermore, subsidence profiles were found to depend on the distribution of underground cavities.

• Polymer(Korea)
• /
• v.29 no.1
• /
• pp.54-58
• /
• 2005

The hydrolytic behavior of microbial poly[(R)-3-hydroxybutyrate]](P(3HB)) has been studied by using two model systems, Langmuir monolayer and solution-grown single crystals (SCs), for elucidating the mechanism for both alkaline and enzymatic degradations. An initial degradation of SCs of P(3HB) leads to breakup lamellae parallel to their short axis (b-axis). Similarly, ridge formation on the lamellar surface appears along the b-axis at lower quenching temperature than melting temperature. Both results support that the lamellar crystals contain less-ordered and more thermally sensitive regions along the b-axis. Although the enzymatic hydrolysis of P(3HB) monolayers was similar to its alkaline one, the enzymatic degradation of P(3HB) monolayers occurred at higher constant surface pressure than the alkaline degradation. This behavior might be attributed to the size of enzymes which is much larger than that of alkaline ions; that is, the enzymes need larger contact area with monolayers to be activated.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.5
• /
• pp.935-943
• /
• 1988

The forming limit diagram is assessed as a means of estimating the forming characteristics of sheet metal and is usually determined experimentally. The strain rates used in the determination are likely to be low. However, often in practice, the strain rates are much higher, so if forming limit diagram is determined at low rates, it may not be appropriate. This paper reconsiders the forming limit diagram for mild steel and aluminum sheet up to variation in strain rate from 10$^{-2}$ sec to 20/sec where its forming has been carried out under oil pressure using a hydraulic bulge test with circular and elliptical dies. To obtain higher strain rate, an impact bulge test had been employed with the same die sets as those used for a hydraulic bulge test. The results obtained are as follows: (1) As the strain rate increases, the fracture pressure increases and the polar height at fracture decreases. (2) Experiment has shown that, in the positive quadrant of the forming limit diagram, the diagram is lowered with increasing strain rate and the effect of strain rate changes according to strain paths and materials..

• The Korean Journal of Health Service Management
• /
• v.13 no.4
• /
• pp.133-144
• /
• 2019

Objectives: To analyze the radiologic results of patients treated with bone defects treated with beta-tricalcium phostphate (β-TCP) in orthopedic surgery. Methods: Medical records of 49 patients, consisting of 24 (49.0%) men and 25 (51.0%) women were retrospectively reviewed. Graft incorporation was evaluated based on Irwin's radiologic staging. Results: The explanatory power of the total regression equation in Irwin's stage at 3 months postoperatively according to three explanatory variables, namely graft tightness, age at diagnosis, and lesion volume, was 65.6%; the explanatory power of Irwin's stage at 6 months postoperatively according to two variables, namely lesion volume and graft tightness, was 32.9%; and the explanatory power of Irwin's stage at 9 months postoperatively for two variables, namely longitudinal lesion length and graft tightness in the total regression, was 30.8%. Conclusions: Graft tightness, lesion volume, age at diagnosis, and longitudinal lesion length are the common factors affecting graft incorporation.

• Journal of the Korean Society of Fisheries and Ocean Technology
• /
• v.19 no.1
• /
• pp.51-56
• /
• 1983

In the stability problem of the U-grooved plate, it has a circular hole, the site of the hole determines some different deformation mode when it was loaded. To determine the optimal position of the circular hole-center which not to get large distortion of the hole itself, in this paper, we studied the distributions of stresses in the neck area between hole and U-groove and the distortion mode of the deformed hole by B.E.M(Boundary Element Method) and compared with experimental results in four cases. For a distributed load, according to the center of the hole moves closer to the U-groove center (c.-c. line), the shape of the circular hole was transformed to the elliptical one(it's major axis perpendicular to the c.-c. line). In this problem, the results by Boundary Element Method was well accorded with Experiments.