• Transactions of the Korean Society for Noise and Vibration Engineering
• /
• v.19 no.6
• /
• pp.583-590
• /
• 2009

An engine is one of the most dominant noise and vibration sources in vehicle systems. Therefore, in order to resolve noise and vibration problems due to engine, various types of engine mounts have been proposed. This work presents a new type of active engine mount system featuring a magneto-rheological (MR) fluid and a piezostack actuator. As a first step, six degrees-of freedom dynamic model of an in-line four-cylinder engine which has three points mounting system is derived by considering the dynamic behaviors of MR mount and piezostack mount. In the configuration of engine mount system, two MR mounts are installed for vibration control of roll mode motion whose energy is very high in low frequency range, while one piezostack mount is installed for vibration control of bounce and pitch mode motion whose energy is relatively high in high frequency range. As a second step, linear quadratic regulator (LQR) controller is synthesized to actively control the imposed vibration. In order to demonstrate the effectiveness of the proposed active engine mount, vibration control performances are evaluated under various engine operating speeds(wide frequency range) and presented in time domain.

• The KSFM Journal of Fluid Machinery
• /
• v.2 no.1 s.2
• /
• pp.7-14
• /
• 1999

This simulation method is developed by using GateCycle code for the performance evaluation of the gas turbine in IGCC(Integrated Gasification Combined Cycle) power plant that uses clean coal gas fuel derived from coal gasification and gas clean-up processes and it is integrated with ASU(Air Separation Unit). In the present simulation method, thermodynamic calculation procedure is incorporated with compressor performance map and expander choking models for considering the off-design effects due to coal gas firing and ASU integration. With the clean coal gases produced through commercially available chemical processes, their compatibility as IGCC gas turbine fuel is investigated in the aspects the overall performance of the gas turbine system. The predictions by the present method show that the reduction of the air extraction from gas turbine to ASU results in a remarkable increase in the efficiency and net power of gas turbines, but it is accompanied with a shift of compressor operation point toward to surge limit. In addition, the present analysis results reveal the influence of compressor performance characteristics of gas turbine have to be carefully examined in designing the ASU integration process and evaluating the overall performance parameters of the gas turbine in IGCC Power plant.

• The KSFM Journal of Fluid Machinery
• /
• v.12 no.4
• /
• pp.30-36
• /
• 2009

Recently, there has been growing interest in the oxyfuel combustion cycle since it enables high-purity $CO_2 capture with high$ efficiency. However, the oxyfuel combustion cycle has some important issues regarding to its performance such as the requirement of water recirculation to decrease a turbine inlet temperature and proper combustion to enhance cycle efficiency. Also, Some of water vapour remain not condensed at condenser outlet because cycle working fluid contains non-condensable gas, i.e., $CO_2$. The purpose of the present study is to analyze performance characteristics of the oxyfuel combustion cycle with different turbine inlet temperatures, combustion pressures and condenser pressure. It is expected that increasing the turbine inlet temperature improves cycle efficiency, on the other hand, the combustion pressure has specific value to display highest cycle efficiency. And increasing condensing pressure improves water vapour condensing rate.

• The KSFM Journal of Fluid Machinery
• /
• v.17 no.1
• /
• pp.12-21
• /
• 2014

An organic Rankine cycle was analyzed to work at the optimal operating point when the heat source is fluctuated. R245fa was adopted as a working fluid, and an axial-type turbine as expander on the cycle was designed to convert the heat energy to the electricity since the turbo-type expander works at off-design points better than the positive displacement-type expander. A supersonic nozzle was designed to increase the spouting velocity because a higher spouting velocity can produce more output power. They were designed by the method of characteristics for the operating fluid of R245fa. Three different cases, such as various spouting velocities, various inlet total temperatures, and various nozzle numbers, were studied. From these results, an optimal operating cycle can be designed with the organic Rankine cycle when the available heat source as renewable energy is low-grade temperature and fluctuated.

• Journal of the Society of Naval Architects of Korea
• /
• v.29 no.3
• /
• pp.90-101
• /
• 1992

Some practical methods have already been proposed for predicting the characteristics of ship manoeuvring motions at relatively high advance speed. However, these methods can hardly be applied to motions of ships in starting, stoppint, backing and slow steaming conditions, even though such extensive motions are of vital importance from a safety point of view particularly in harbour areas. The method presented here aims at predicting the characteristics of ship manoeuvring at low advance speed, which covers starting, stopping, backing and slow steaming conditions. The force mathematical models at large angles of incidence to the hull as well as under the tilde range of propeller operations are formulated. Simulations of various manoeuvres at low advance speed are carried out for two types of merchant ship, i.e. a LNGC and a VLCC. Comparisons between simulations and corresponding full-scale measurements or free-running model tests provide a first verification of the proposed mathematical models.

• 유체기계공업학회:학술대회논문집
• /
• 2003.12a
• /
• pp.568-572
• /
• 2003

The height of valve body is limited to 30mm in the cook-top style gas valves for the domestic gas ranges. But the all the safety specifications of KS should be fulfilled and the magnetic power unit(MPU) should be installed in the valve body for the safety reason. The length of MPU body is longer than the 30mm that it should be located in the square direction of the knob shaft and therefore the implementation of the lever mechanism to transmit the press motion of the knob to the MPU valve is very difficult. In this paper, the hinged lever with inclined plate is used to transmit the press motion of the knob to the MPU valve. The analysis of the gas flow with using the commercial software of FLOW-3D shows that the gas flow capacity is fit for the domestic gas range. The performance and responsibility of the valve is tested for the mass production and the test results shows that the valve can be installed in the commercial gas range.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.46 no.9
• /
• pp.703-711
• /
• 2018

A preliminary design tool of a hypersonic Ludwieg tube facility which simulates real-flight environment was developed and its performance was verified by CFD(Computation Fluid Dynamics) calculations. The operating theory of Ludwieg tube was studied to develop the preliminary design tool. Using the preliminary design tool, Ludwieg tube specifications were determined to satisfy target performance. The Ludwieg tube which produces high speed flows(the Mach number ranging 4 to 10) was designed. Especially altitude simulation at Mach 4 flow could be performed.

• Journal of the Korean Institute of Navigation
• /
• v.14 no.4
• /
• pp.41-52
• /
• 1990

Due to the constantly varying sea-state with which any wave energy conversion device must contend in order to extract energy efficiently , the ability to control the device's position relative to the incident waves is critical in achieving the creation of a truly functional and economical wave energy device. In this paper, the authors will propose methodology based on the theory of a variable structure system to utilize a three dimensional source distribution as a model to estimate anticipated surge, sway and yaw of a wave energy conversion device relative to varying angles and characteristics of incident waves and there from derive a feedback to a sliding mode controller which would reposition the device so as to maximize its ability to extract energy from waves in constantly varying ocean conditions.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.34 no.1
• /
• pp.35-43
• /
• 2010

In this study, an ideal water-recirculated oxy-fuel power generation system is proposed. The results of parametric studies of the performance characteristics of the system are discussed. For a given choice of the turbine inlet temperature, the turbine, which produces power, can be either a gas or a steam turbine. For maximum efficiency, the turbine inlet temperature is selected as the level of state-of-the-art gas turbines and the reheat cycle may be adopted not only to enhance the turbine power but also to maintain dryness of the water with a turbine exhaust temperature that is as high as possible. To obtain a low condensation temperature for a high purity of $CO_2$, a relatively low pressure expansion process may be added. Finally, the performance of the water-recirculated oxy-fuel power generation system is discussed with reference to various operating parameters and system configurations. The optimal operating conditions for high performance and a high purity of $CO_2$ are proposed.

• Journal of Sensor Science and Technology
• /
• v.6 no.1
• /
• pp.72-80
• /
• 1997

One of the concerns in micro fluidic valve designs is that of reverse direction leakage. This paper designs and fabricates a new fluidic valve to achieve zero leakage. The design uses flapper and nozzle elements. In the forward direction the working fluid pushes the flapper upward to allow flow. In the reverse direction, the flapper pushes against the orifice seat, and thus, no flow can be generated, unless the flapper or nozzle element breaks. The nozzle element fabrication involves fabricating an orifice by wet etching of (100) wafer, The flapper element fabrication involves $20{\mu}m$ deep patterning of the negative image of the flapper, followed by wet etching from backside. Flow experiments were conducted with DI water as the working fluid, and the results are compared to analytical predictions. The results show that the developed flapper-nozzle valve achieves a true diodic flow characteristic.