• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2006.11a
• /
• pp.239-240
• /
• 2006

저손실 고투자율 특성을 가지는 ${\alpha}-Fe$ 나노결정 자심재료를 제조하기 위한 열처리 온도 변화에서, $510^{\circ}C$의 열처리 조건에서 가장 높은 투자율과 신호전송 특성을 나타내었다. 저주파 대역에서의 신호 전송 특성은 자심재료의 자기적 특성에 지배적인 영항을 받으며, 고주파 대역의 신호전송 특성은 임피던스 매칭으로 향상시킬 수 있었다. 그리고 커플러의 출력부에 신호증폭장치를 삽입하여 자기유도에 의해 신호가 커플링될 때 발생하는 삽입손실을 보완하여 커플러의 특성을 향상시킬 수 있었다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.541-545
• /
• 2003

Mn-Zn 페라이트의 자심재료가 전자기 부품용 응용될 때, 소형화와 고효율화를 이루기 위한 공정변수에 따른 전자기적 특성변화를 고찰하였다. ZnO 의 몰비가 11 mole일 때, 가장 우수한 특성을 나타내었으며, $SiO_2$와 CaO는 입계 저항층 형성을 통한 손실을 감소시키고, 이로 인해 성능지수는 증가하여 $100\;kHz\;{\sim}\;200\;kHz$ 범위에서 최대값을 나타내어 전자기적 효율이 극대화되었다. 산소분압의 제어는 승온과정부터 산소분압을 제어시켜주어야만 Zn-loss 현상의 증가와 $Fe^{2+}$ 이온 농도의 감소 및 $Fe^{2+}-\;Fe^{3+}$ 이온간의 호핑(hoping)현상 등에 의한 손실을 최소화할 수 있으며, 높은 투자율을 얻을 수 있었다. 그리고 소결 또는 냉각 중 평형 산소분압이 유지되지 못하면 다량의 결함이 출현하게 되고, 특히 $600^{\circ}C$ 이하에서 스피넬 상의 분해-산화반응이 일어나면서 미세구조 상에 결함으로 남게 되어 전자기적 특성이 저하되었다.

• Korean Chemical Engineering Research
• /
• v.54 no.1
• /
• pp.44-51
• /
• 2016

The powder core, conventionally fabricated from iron particles coated with insulator, showed large eddy current loss under high frequency, because of small specific resistance. To overcome the eddy current loss, the increase in the specific resistance of powder cores was needed. In this study, copper oxide coating onto electrically conductive iron particles was performed using a planetary ball mill to increase the specific resistance. Coating factors were optimized by the Response surface methodology. The independent variables were the CuO mass fraction, mill revolution number, coating time, ball size, ball mass and sample mass. The response variable was the specific resistance. The optimization of six factors by the fractional factorial design indicated that CuO mass fraction, mill revolution number, and coating time were the key factors. The levels of these three factors were selected by the three-factors full factorial design and steepest ascent method. The steepest ascent method was used to approach the optimum range for maximum specific resistance. The Box-Behnken design was finally used to analyze the response surfaces of the screened factors for further optimization. The results of the Box-Behnken design showed that the CuO mass fraction and mill revolution number were the main factors affecting the efficiency of coating process. As the CuO mass fraction increased, the specific resistance increased. In contrast, the specific resistance increased with decreasing mill revolution number. The process optimization results revealed a high agreement between the experimental and the predicted data ($Adj-R^2=0.944$). The optimized CuO mass fraction, mill revolution number, and coating time were 0.4, 200 rpm, and 15 min, respectively. The measured value of the specific resistance of the coated pellet under the optimized conditions of the maximum specific resistance was $530k{\Omega}{\cdot}cm$.

• Resources Recycling
• /
• v.11 no.5
• /
• pp.30-33
• /
• 2002

Recently in the progress of electronic equipment, power transformer was considered an important part. To make power transformer with miniaturization, lightening, low Power, we need a high efficiency core material. In this paper, we added $V_2$$O_{5}$ and $CaCo_3$ to Mn-Zn Ferrite to make a high efficiency, low loss core material. The compositions are MnO : ZnO : $Fe_2$$O_3$=37 : 11 : 52 mol%. They were sintered at 1250 for Three hours. Initial permeability was measured at 0.1 MHz. At 200 mT, Power loss was measured by temperature changing at 25 KHz, 50 KHz, 100 KHz. When we added $V_2$$O_{5}$ and $CaCo_3$, 0.08 wt%, 0.05 wt% respectively, we get 415 ㎾/㎥ at 200 mT, 100 KHz, $60^{\circ}C$. We can reduce eddy current loss as a main loss of high frequency by addition of a little mount of $V_2$$O_{5}$ $CaCo_3$. So we can decrease the power transformer's power loss.

• Journal of Plant Biotechnology
• /
• v.36 no.1
• /
• pp.1-6
• /
• 2009

A study was conducted to investigate in vitro micro propagation of four potato cultivars of Daese, Jasim, Chubaek and Haryeng in MS medium and PM medium (a medium containing half concentration of $NH_4NO_3$ and $KNO_3$, two fold concentration of $CaCl_2$ as compared to MS medium). During $1{\sim}2$ weeks of culture, Daese and Jasim showed better shoot elongation on the solid MS medium than Chubaek and Haryeng whereas Chubaek and Haryeng did better shoot elongation on the solid PM medium. But no difference was observed after 4 weeks of culture. As compared to shoot elongation on the solid medium, it was delayed at early stage of culture in the liquid medium without shaking. Shoot formation ratio of potato (above 4 cm of shoot length) began to increase significantly after 1 week of culture and kept on increasing until 4 weeks. The four cultivars showed the different patterns of shoot growth in bioreactor. The PM medium with a quarter salt strength was effective for the regeneration of axillary buds as well as shoot elongation of Jasim and Chubaek. Daese showed vigorous regeneration of axillary buds in the PM medium with a half salt strength. On the other hand, Haryeng showed slower growth than the other three cultivars.

• Journal of the Korean Magnetics Society
• /
• v.15 no.3
• /
• pp.191-197
• /
• 2005

In the fabrication process of Fe-based amorphous alloy powder cores by pulverization of the melt-spun ribbons and cold compaction, the effects of powder preparation method on the magnetic & electric properties, powder shapes and microstructure of cores have been investigated. The powder cores made by using rotor mill showed low effective permeability as compared to the cores prepared by ball milling. However the frequency dependence and quality factor properties were superior in the case of rotor-milling. Further the powders prepared by rotor mill had homogeneous and round shapes through strong shearing in the sieve ring, while the ball milled powders were inhomogeneous and relatively small. The lower permeability of the powder cores fabricated with rotor mill was considered to be due to the high internal stress occurred by very intensive shearing. Moreover the powder cores produced by rotor-milling showed lower core loss and good frequency dependence of effective permeability possibly due to the higher electrical insulation between magnetic particles. The dc bias property of the powder cores made by rotor-milling was better than the one by ball-milling.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.11a
• /
• pp.95-98
• /
• 2002

전력선 통신 blocking filter용 자심 재료를 개발하기 위해서 MnO 24 mol%, ZnO 25 mol% and $Fe_{2}O_{3}$ 51 mol% 의 기본조성에 $MoO_{3}$, $SiO_{2}$, CaO를 첨가하여 $1350^{\circ}C$에서 대기압 상수 A를 7.8롤 고정하고 소결하여 미세구조를 제어하였으며 기본 조성에 $MoO_{3}$ 400 ppm, $SiO_{2}$ 100 ppm and CaO 200 ppm을 첨가한 경우 평균 입경 $25{\mu}m$ 의 균일한 결정립으로 구성된 미세구조를 얻었고 기공의 감소에 의한 치밀화로 $4.98g/cm^{2}$의 고밀도화가 이루어 졌다. 또한 소결체의 균일한 미세구조와 고밀도화로 인해서 8221(${25^{\circ}C}$, 1 KHz) 의 가장 높은 투자율 특성을 나타냈다. 시편의 온도가 증가함에 따라 투자율이 증가되어 ${110^{\circ}C}$에서 13904의 거대 투자융이 측정되었고, 코일의 인가주파수가 1 KHz에서 1 MHz까지 증가됨에 따라 최고 ${102^{\circ}C}$까지 시편 온도가 상승하였다. 가장 높은 투자율 특성을 나타낸 ferrite 코어를 사용하여 단상 및 3상용 블로킹 필터의 감쇄율을 측정한 결과 현재 국내의 전력선 통신용 주파수 대역으로 규정되어 있는 10 KHz ~ 450 KHz 대역에서 각각 -46.46 dB와 -73.9 dB의 최고 값을 얻었다.

• Journal of the Korean Magnetics Society
• /
• v.17 no.6
• /
• pp.226-231
• /
• 2007

High frequency loss property of nanocrystalline amorphous ribbon with a high resistivity insulation layer of $TiO_2$ and $SiO_2$ was studied. The insulation layer was fabricated by sol-gel method using dip-coating. The optimum composition ratio of metal alkoxide and slurry for fabrication of insulation layer was established and insulation layer with high adhesion was coated on the nanocrystalline amorphous ribbon. Frequency loss of magnetic core material manufactured on nanocrystalline amorphous ribbon with the surface insulation layer decreased over 40 % compared with that of magnetic core material without surface insulation layer. The insertion loss of an inductive coupler, which was prepared by using magnetic core material coated insulation layer, decreased due to reduction of frequency loss for magnetic core material and insertion loss decreased in proportion to frequency.

• Journal of the Korean Magnetics Society
• /
• v.8 no.4
• /
• pp.185-191
• /
• 1998

Magnetic domain structure and static magnetic properties were investigated in the ultra thin 3%Si-Fe strip wound cores when the strips were wound and annealed to relief the stress. The elastic and plastic deformation due to the radius of curvature was also investigated for the cores. At the as-wound state, the maze pattern domain structure was generated on the concave surface of the core and 180$^{\circ}$ domain wall was recovered by annealing 600 $^{\circ}C$$\times$30 min. After annealed by 900 $^{\circ}C$$\times$30 min, Hc of strip-wound cores was not reached to the $H_c$ of the strip even at the cores of elastic deformation region. It is necessary to relief the local stress remained in the core when the cores were manufactured for the application of ultra-thin 3%Si-Fe strip.

• Microbiology and Biotechnology Letters
• /
• v.46 no.4
• /
• pp.372-376
• /
• 2018

To investigate the bio-activities of lotus (Nelumbo nucifera Gaertner), ethanol extracts were prepared from different parts of lotus, including lotus root, node of root (NR), leaf, pod of seed (PS), seed (S), and embryo of seed (ES), respectively. Anti-thrombosis activities were evaluated. NR, S, and PS extracts displayed strong anti-coagulation activities, as evidenced by the inhibition of thrombin, prothrombin, and coagulation factors, respectively. NR, leaf, S, and PS extracts displayed strong platelet aggregation inhibitory activities. The aggregation inhibition of S and PS extract was comparable to that of aspirin. The extracts of NR, S, and PS did not show hemolysis activity up to 1.0 mg/ml.