• Journal of the Korean Magnetics Society
• /
• v.9 no.2
• /
• pp.71-77
• /
• 1999

본 연구에서는 이방성 Nd-Fe-B계 자성분말과 바인더로 polypropylene을 사용하여 compound를 제조한 후 사출성형에 의해 이방성 Nd-Fe-B 레진본드자석을 제조하여 자성분말의 함량, 인가자장 및 사출성형 온도에 따른 자기적 특성 및 유변학적 특성을 조사하였다. Torque sensor에 의해 측정한 본 연구에 사용된 이방상 Nd-Fe-B계 자성분말의 최대 분말함량은 70.7vol%이었다. Compound의 자성분말 함량이 증가함에 따라 레진본드자석의 잔류자속밀도와 최대자기에너지적은 증가하여 54vol%에서 최대값을 보인후 다시 감소하였고, 보자력은 변화가 없었다. 54vol% 자성분말 함량 이상에서 잔류자속밀도와 최대자기에너지적이 다시 감소하는 것은 사출성형시 자성분말의 배향도 저하에 기인한다. 이것은 compound의 자성분말 함량이 증가함에 따라 compound의 유동성이 저하되어 사출성형시 자성분말의 이방화를 어렵게 만들기 때문이다. 사출성형 온도가 증가함에 따라 레진본드자석의 자기적 특성은 증가하였다. 이는 성형온도가 증가함에 따라 compound의 유동성이 향상되어 자성분말의 배향도가 증가되었기 때문이다. 따라서 사출성형에 의해 이방성 Nd-Fe-B계 레진본드자석 제조시 자기적 특성을 향상시키기 위해서는 compound의 자성말 함량 뿐만 아니라 compound의 유동성이 중요하게 고려되어야 한다.

• Journal of the Korean Magnetics Society
• /
• v.11 no.4
• /
• pp.157-162
• /
• 2001

Rheological characteristics of Sm-Co type plastic magnet compound for powder injection molding process were investigated with the variation of the magnetic powder size, their relative contents and volume fraction using the mixture of fine and coarse powder. Shear viscosity of Sm-Co type compound was decreased with increasing the size of coarse powder due to the increase of powder packing density. However, the smaller the average size of fine powder resulted in the higher viscosity of compound due to the increase of agglomeration force. In case of mechanically milled Sm-Co type powder, the viscosity of compound with the mixture of coarse powder of 125∼75 ㎛ and fine powder of average size of 4.9 ㎛ greatly depends on their relative contents and shows a minimum value at the 60 % coarse powder fraction. This means that the compound shows a maximum packing density at the 60% coarse powder fraction. Compound viscosities satisfied well the rheological model with the volume fraction of magnetic powder, and maximum volume fraction of magnetic powder in Sm-Co type compound for powder injection molding was about 66%.

• Journal of the Korean Magnetics Society
• /
• v.4 no.3
• /
• pp.219-225
• /
• 1994

The alignment of Sr-ferrite magnetic powders, which is usually related to the fluidity and the applied magnetic field, is investicated in the anisotropic Sr-ferrite / resin-bonded permanent magnets. The magnetic powder alignment is observed to increase with the applied magnetic field and the fluidity which is a function of molding temperature and powder packing ratio. The best magnetic powder alignment is achieved at the following conditions; Sr-ferrite packing ratio of 56vol%, apparent viscosity of about 3000 poise in $1000sec^{-1}$ shear rate, and applied magnetic field of about 5kOe. The degree of preferred orientation of the magnetic powders in the field direction, as determined by the dc hysterisis graphs, is 84~85% (0.84~0.85). This result is in agreement with the value of 0.85 obtained by the X-ray experiments in the $2{\theta}$ range of ${23~40}^0$. The best magnetic properties obtained are:2.2kG of remanent flux density, 2.2MGOe of maximum energy product.

• Polymer(Korea)
• /
• v.25 no.2
• /
• pp.240-245
• /
• 2001

The effect of additives on the orientation of magnetic Sr-ferrite powders has been studied during powder injection molding under applied magnetic field for fabricating multi-pole anisotropic sintered Sr-ferrite magnets. The orientation of the Sr-ferrite powders depends sensitively on the fluidity of powder-binder mixture, related to the binder additives and the injection molding temperature, and the magnetic field intensity. The orientation of Sr-ferrite powders is good for the compacts with stearic acid added in the binder system of paraffin wax/carnauba wax/HDPE, but it is poor for the compacts with silane coupling agent added. The orientation of Sr-ferrites higher than 80% is achieved at the following useful conditions; apparent viscosity lower than 2500 poise in 1000 sec$^{-1}$ shear rate and applied magnetic field higher than 4 kOe.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2015.11a
• /
• pp.263-263
• /
• 2015

절연층이 코팅된 연자성복합체(Soft magnetic composites) 분말 성형 시 발생하는 밀도와 강도 저하의 문제를 개선하기 위해 금속산화물 전구체로 표면 개질된 자성분말을 성형 후 경화시키는 방법으로 분말 자심을 제조하였다. 이를 통해 공정이 단순화 되면서 자심의 물리적 내구성을 향상시킬 수 있음을 확인하였다.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2002.12a
• /
• pp.238-239
• /
• 2002

현대의 영구자석들은 Alnico 주조자석을 제외하고는 모두 자성분말을 이용한 분말야금학적인 소결자석 또는 본드자석 형태로 제조된다. 따라서 자성분말의 형상, 크기, 입도, 순도, 조성 등이 자석의 자기적 특성을 우선적으로 결정하며, 이러한 구조적, 화학적 인자들은 영구자석의 고성능화를 위해 자성분말 또는 결정립이 초미세화 함에 따라 자기 특성을 결정하는 더욱 중요한 요소로 작용하고 있다. 그러므로 이들 인자와 자기적 특성간의 상관관계를 정확히 규명하고 보다 잘 이해하는 것이 극대화된 자기 특성을 갖는 자성체를 개발하는데 절대적으로 필요하다. (중략)

• Journal of the Korean Magnetics Society
• /
• v.18 no.5
• /
• pp.195-199
• /
• 2008

Composites of $Fe_{93.5}Si_{6.5}$ powder and epoxy were prepared using a thermal curing process. Scanning electron microscope (SEM), vibrating sample magnetometer (VSM) and network analyzer were used to analyze the structure, electromagnetic properties and microwave absorption of the composites. Results show that the saturation magnetization depends on the fraction of the $Fe_{93.5}Si_{6.5}$ powder in the composite, which affects initial permeability. It is believed that the eddy current loss is a dominant factor over 1 GHz and that the resonance frequency of the composite decreases with increasing fractions of $Fe_{93.5}Si_{6.5}$ powder. Finally, reflection loss was calculated from the permeability and permittivity of these composites. Composite with 50 wt.% $Fe_{93.5}Si_{6.5}$ powder fractions and 5 mm thickness showed reflection loss below -20 dB from 3.66 GHz to 4.16 GHz. Therefore, it is believed that thin Fe-Si/epoxy composites may be a good candidate for microwave absorption application.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2000.11a
• /
• pp.37-38
• /
• 2000

• Proceedings of the Korean Magnestics Society Conference
• /
• 2014.05a
• /
• pp.96-96
• /
• 2014

• Journal of the Korean Magnetics Society
• /
• v.21 no.2
• /
• pp.77-82
• /
• 2011

The use of soft magnetic materials have been increasing in the various industrial fields according to the increasing demand for high performance, automatic, miniaturing equipments in the recent our life. In this study, we investigated the effect of factors on the core loss and magnetic properties of electrical steel and soft magnetic composites. Furthermore, we reviewed the major efforts to reduce the core loss and improve the soft magnetic properties in the two main soft magnetic materials. Domain purification which results from reduced density of defects in cleaner electrical steels is combined with large grains to reduce hysteresis loss. The reduced thickness and the high electrical conductivity reduce the eddy current component of loss. Furthermore, the coating applied to the surface of electrical steel and texture control lead to improve high permeability and low core loss. There is an increasing interest in soft magnetic composite materials because of the demand for miniaturization of cores for power electronic applications. The SMC materials have a broad range of potential applications due to the possibility of true 3-D electromagnetic design and higher frequency operation. Grain size, sintering temperature, and the degree of porosity need to be carefully controlled in order to optimize structure-sensitive properties such as maximum permeability and low coercive force. The insulating coating on the powder particles in SMCs eliminates particle-to-particle eddy current paths hence minimizing eddy current losses, but it reduces the permeability and to a small extent the saturation magnetization. The combination of new chemical composition with optimum powder manufacturing processes will be able to result in improving the magnetic properties in soft magnetic composite materials, too.