• 동력기계공학회지
• /
• 제15권5호
• /
• pp.67-71
• /
• 2011

Fine blanking is a specialized form of blanking where there is no fracture zone when shearing. This is achieved by compressing the whole part and then an upper and lower punch extract the blank. This allows the process to hold very tight tolerances, and perhaps eliminate secondary operations. In the present study, tensile test and numerical simulation has been performed to investigate distribution of deformation and stress of car seat recliner. The commercial ABAQUS/Explicit software was applied for analyzing the stress and strain of the recliner. In analysis, three lock gear has reached the maximum moment on rotational degree of 2.27. This is more than two times than maximum moment of same size recliner, and can be used safely. Therefore, these can use as criterion of actual structural design.

• 한국산학기술학회:학술대회논문집
• /
• 한국산학기술학회 2011년도 춘계학술논문집 2부
• /
• pp.824-827
• /
• 2011

본 논문에서는 자동차 시트 리클라이너 기어의 파인 블랭킹 성형 실험을 통하여 V-링 설치 위치에 따른 기어의 다이 롤 높이 변화를 검토하였다. 3 종류의 다이 편과 가이드 플레이트 편을 설계하여 파인 블랭킹 금형을 제작하였으며 650 ton 파인블랭킹 프레스에서 성형 실험을 수행하였다. 실험으로부터 제품을 취출하여 다이 롤 높이를 측정하여 분석한 결과 기어 모듈과 관계없이 V-링 설치 위치가 가이드 플레이트에서 멀어짐에 따라 다이 롤 높이가 증가함을 파악할 수 있었다. 이와 같은 결과는 향후 파인 블랭킹 금형의 V-링을 설계할 때 다이 롤 높이를 최소화하기 위하여 유용하게 활용될 수 있을 것이다.

• 한국자동차공학회논문집
• /
• 제17권1호
• /
• pp.64-71
• /
• 2009

The development of more safe recliners is an important issue in the automotive industry. However, the development of new recliners is costly and take much time because it is typically based on experimental evaluation using prototypes. This study presents the evaluation of rear crashworthiness for round recliner using finite element method. That reduces the number of repeating test and gives an information about stiffness. To evaluate rear crashworthiness, the FMVSS 301 simulation and pendulum impact simulation were performed. The load path on two simulations was observed and compared each other in this paper. Also stress, strain and internal energy was compared. It is attempted the tooth strength simulation using a substructure option on PAM-CRASH.

• 한국정밀공학회지
• /
• 제25권7호
• /
• pp.64-71
• /
• 2008

Burr generated on plate holder should be removed through additional process, because it has an influence on the function of automotive seat recliner. The process layout to perform simultaneously embossing and half blanking of plate holder has been developed in this study in order to minimize the influence of burr formation. The optimal process condition to satisfy the required dimensional accuracy of plate holder has been determined using Taguchi method and finite element analysis. It has been shown from experimental results that the proposed method is decidedly superior to the previous FCF method from the aspect of sheared surface, roll-over, flatness and burr height.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2012년도 춘계학술대회 논문집
• /
• pp.125-126
• /
• 2012

• Tribology and Lubricants
• /
• 제35권3호
• /
• pp.183-189
• /
• 2019

The driver seat of an automobile is in direct contact with the driver and provides the driver with a safe and comfortable ride. The seat consists of a frame, a rail, and many recliners. In recent years, strength and operating force measurement testing of the recliner have become vital for designing car seats. However, performance evaluation requires expensive testing equipment, numerous seat products, and considerable time. Therefore, the trend is to reduce experimentation through interpretation. This study examines the lubrication of solid lubricant for automotive seat recliners and confirms the friction and wear performance. In this study, the lubrication behavior of solid lubricants for car seat recliners is investigated to ascertain the friction and wear performance and to provide accurate values for the strength analysis. The friction material consists of a pin and a plate made from steel, which is widely used in recliners. The friction and wear under lubrication conditions are measured by a reciprocating friction wear tester. The friction coefficient is obtained according to the load and speed. Based on the obtained results, it is possible to achieve a reduction in the error of the test value and the analysis by providing the friction coefficient and wear of the lubricant. The results can be applied to the analysis of automobile seat design.

• 한국정밀공학회지
• /
• 제25권7호
• /
• pp.55-63
• /
• 2008

Fine blanking is a process of press shearing which makes it possible to produce the thick sheet metal of the finished surface and the close dimensional accuracy over the whole material thickness in the single blanking operation. In this paper, a plate holder of automotive seat recliner is manufactured by FCF(Flow Control Forming) method using the conventional mechanical press instead of the fine blanking press. Main processes for manufacturing of the plate holder by FCF method are embossing, half blanking and trimming processes. Optimal clearance, stripper force and counter force to increase the dimensional accuracy of the plate holder have been investigated by FE-analysis. As a result of FE-analysis, the clearance for both embossing and half blanking processes was -2%t and the forces of stripper and counter were 25ton and 15ton, respectively. After manufacturing the plate holder by FCF method, the measured dimensional characteristics have been compared with the required specifications as the final product. Although the dimensional accuracy of the plate holder manufactured by FCF method was a little inferior to that by fine blanking process, it was satisfactory in a general sense.

• 한국자동차공학회논문집
• /
• 제11권6호
• /
• pp.205-212
• /
• 2003

This paper may provide a basic design data for the safer car seat mechanism and the quality of the material used by finding out the passenger's dynamic behavior when protected by seat belt during collision. A computer simulation with finite element method is used to accomplish this objective. At first, a detailed geometric model of the seat is constructed using CAD program. The formation of a finite element from a geometric data of the seat is carried out using Hyper-Mesh that is the commercial software for mesh generation and post processing. In addition to seat modeling, the finite element model of seat belt and dummy is formed using the same software. Rear impact analysis is accomplished using Pam-Crash with crash pulse. The part of the recliner and right frame is under big stress in rear crash analysis because the acceleration force is exerted on the back of the seat by dummy. The stress condition of the part of the bracket is checked as well because it is considered as an important variable on the seat design. Front impact model which including dummy and seal belt is analyzed. A Part of anchor buckle of seat frame has high stress distribution because of retraction force due to forward motion of dummy at the moment of collision. On the basis of the analysis result, remodeling and reanalysis works had been repeatedly done until a satisfactory result is obtained.