• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.38 no.10
• /
• pp.712-720
• /
• 2001

Algorithms from the research of the layout migration were proposed in the paper. These are automatic recognition algorithm for the VLSI devices from it, graph based construction algorithm to maintain the constraints, dependencies, and design rule between the devices, and high speed compaction algorithm to reduce size of the VLSI area and reuse the design with compacted size for the new technology. Also, this paper describes that why proposed algorithms are essential for the era of the SoC (System on a Chip), design reuse, and IP DB, which are the big concerns in these days. In addition to introduce our algorithms, the benchmark showed that our performance is superior by 27 times faster than that of the commercial one, and has better efficiency by 3 times in disk usage.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.9
• /
• pp.517-524
• /
• 2019

The overdrive hub clutch is attached to a 6-speed automatic transmission to reduce fuel consumption by using the additional power of the engine. This paper proposes a means to minimize the load and roll-over ratio on the punch during the piercing process for the overdrive hub clutch product. Die clearance, shear angle, and friction coefficient, which can affect the load and roll-over ratio of the punch during processing, were set as the design variables. Sensitivity analysis was also conducted to determine the influence of each design variable on the punch load and roll-over ratio. As a result, shear angle, friction coefficient and die clearance were found to be sensitive to load and roll-over ratio. The punch load and roll-over ratio were set as the objective function and the equation of each design variable and objective function was derives using the Response Surface Method. Finally, the optimal value of the design variables was derived using the Response Surface Method. Application of this model to finite element analysis resulted in 22.14% improvement in the roll-over ratio of the punch load and material.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.18 no.6
• /
• pp.854-862
• /
• 1993

All of the CMOS analog and analog-digital systems have composed with several basic circuits, and among them, a important block, the amplifier part can affect the system's performance, Therefore, according to the uses in the system, the amplifier circuit have designed as various architectures (high-gain, low-noise, high-speed circuit, etc...). In this paper, we have proposed a new CMOS differential amplifier circuit. This circuit is differential to single ended input stage comprised of CMOS complementary gain circuits having internally biasing configurations. These architectures can be achieved the high gain and reduced the transistors for biasing. As a results of SPICE simulation with the standard $1.5{\mu}m$ processing parameter, the gain of the proposed circuit have a doubly value of the typical circuit's while maintaining other characteristics(phase margin, offset, etc...). And the proposed circuit is applicated in a simple CMOS comparator which has the settling time in 7nsec(CL=1pF) and the igh output swing $({\pm}4.5V)$.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.12 no.6
• /
• pp.279-283
• /
• 2012

In is paper, we design and implement the low power, high speed touch screen controller that calculates and outputs the coordinate of touch point on the touch screen of mobile devices. The system clock is 10HMz, the number of input channels is 21, standby current is $20{\mu}A$, dynamic range of input is 140pF~400pF and the response time is 0.1ms/frame. It contains the power management unit for low power, automatic impedance calibration unit in order to adapt to humidity, temperature and evaluation board, adjacent key and pattern interference suppression unit, serial interface unit of I2C and SPI. The function and performance is verified by using FPGA and $0.18{\mu}m$ CMOS standard process. The implemented touch screen is designed for using in the double layer ITO(Indium Thin Oxide) module with diamond pattern and single layer ITO module for cost-effective which are applied to mobile phone or smart remote controller.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.8
• /
• pp.1877-1886
• /
• 2010

In this paper, we design a redundancy control circuit for 1T-SRAM repair using electrical fuse programming. We propose a dual port eFuse cell to provide high program power to the eFuse and to reduce the read current of the cell by using an external program supply voltage when the supply power is low. The proposed dual port eFuse cell is designed to store its programmed datum into a D-latch automatically in the power-on read mode. The layout area of an address comparison circuit which compares a memory repair address with a memory access address is reduced approximately 19% by using dynamic pseudo NMOS logic instead of CMOS logic. Also, the layout size of the designed redundancy control circuit for 1T-SRAM repair using electrical fuse programming with Dongbu HiTek's $0.11{\mu}m$ mixed signal process is $249.02 {\times}225.04{\mu}m^{2}$.

• Journal of Korea Society of Industrial Information Systems
• /
• v.21 no.1
• /
• pp.61-70
• /
• 2016

This paper describes a new PMU(parametric measurement unit) design technique for automatic test equipment(ATE). Only one DDA(differential difference amplifier) is used to force the test signals to DUT(device under test), while conventional design uses two or more amplifiers to force test signals. Since the proposed technique does not need extra amplifiers in feedback path, the proposed PMU inherently guarantees stable operation. Moreover, to measure the response signals from DUT, proposed technique also adopted only one DDA amplifier as an IA(instrument amplifier), while conventional IA uses 3 amplifiers and several resistors. The DDA adopted two rail-to-rail differential input stages to handle full-range differential signals. Gain enhancement technique is used in folded-cascode type DDA to get open loop gain of 100 dB. Proposed PMU design enables accurate and stable operation with smaller hardware and lower power consumption. This PMU is implemented with 0.18 um CMOS process and supply voltage is 1.8 V. Input ranges for each force mode are 0.25~1.55 V at voltage force and 0.9~0.935 V at current force mode.

• Journal of Korea Society of Industrial Information Systems
• /
• v.19 no.4
• /
• pp.17-24
• /
• 2014

In this paper, we propose a CMOS FM RX front-end structure with an automatic tunable input matching network and implement it using a 65nm CMOS technology. The proposed FM RX front-end is designed to change the resonance frequency of the input matching network at the low noise amplifier (LNA) according to the channel frequency selected by a phase-locked loop (PLL) for maintaining almost constant sensitivity level when an embedded antenna type with high frequency selectivity characteristic is used for FM receiver. The simulation results of implemented FM front-end show about 38dB of voltage gain, below 2.5dB of noise figure, and -15.5dBm of input referred intercept point (IIP3) respectively, while drawing only 3.5mA from 1.8V supply voltage including an LO buffer.

• Composites Research
• /
• v.28 no.4
• /
• pp.226-231
• /
• 2015

Various characteristics(thermal expansion, microstructure, etc.) and mechanical properties of CNT-aluminum nano composites manufactured by volume production system were evaluated. Also, formability and durability were evaluated for potential applications in automotive parts, via compared with high-elasticity material (A390) and the current commercial product. As a result, this composite has excellent mechanical properties and formability, therefore, to verity its potential for application as light and high strength materials in automobile part.

• Journal of Korea Society of Industrial Information Systems
• /
• v.20 no.6
• /
• pp.29-36
• /
• 2015

This paper presents an LED backlight driver IC consisting of three linear current regulators and an output-voltage regulation loop with a self-adjustable reference voltage. In the proposed LED driver, the output voltage is controlled by dual feedback loops. The first loop senses and controls the output voltage, and the second loop senses the voltage drop of the linear current regulator and adjusts the reference voltage. With these feedback loops, the voltage drop of the linear current regulator is maintained at a minimum value, at which the driver efficiency is maximized. The output of the driver is a three-channel LED setup with four LEDs in each channel. The luminance is adjusted by the PWM dimming signal. The proposed driver is designed by a $0.35-{\mu}m$ 60-V high-voltage process, resulting in an experimental maximum efficiency of approximately 85%.

• Journal of the Institute of Electronics Engineers of Korea SD
• /
• v.46 no.9
• /
• pp.74-80
• /
• 2009

This paper describes a $2{\sim}6GHz$ CMOS frequency synthesizer that employs only one LC-tank voltage controlled oscillator (VCO). For wide-band operation, optimized LO signal generator is used. The LC-tank VCO oscillating in $6{\sim}8GHz$ provides the required LO frequency by dividing and mixing the VCO output clocks appropriately. The frequency synthesizer is based on a fractional-N phase locked loop (PLL) employing third-order 1-1-1 MASH type sigma-delta modulator. Implemented in a $0.18{\mu}m$ CMOS technology, the frequency synthesizer occupies the area of $0.92mm^2$ with of-chip loop filter and consumes 36mW from a 1.8V supply. The PLL is completed in less than $8{\mu}s$. The phase noise is -110dBC/Hz at 1MHz offset from the carrier.