• 한국자기학회지
• /
• 제26권3호
• /
• pp.86-91
• /
• 2016

BLDC 전동기의 코깅토크는 영구자석과 철심의 상호작용에 의해 발생하고 소음과 진동을 발생시키는 요인이다. 제조 과정에서 조립 공차로 인해 영구자석이 회전자 철심 면에 제대로 붙지 않을 경우 BLDC 전동기의 전자기적 구조가 변할 수 있다. 본 논문에서는 조립 공차로 인해 자석이 회전자 표면과 분리되었을 때 코깅토크에 미치는 영향에 대해 연구했다. 핵심적인 설계 요소들인 회전자와 자석 간 분리, 분리를 가진 자석 수, 이웃한 자석들 간의 여러 배치형태를 고려했다. 코깅토크 해석을 위해 유한요소법을 사용하였고, 소음진동을 발생시키지 않는 조립 공차를 제안했다. 제안된 조립 공차로 제작된 BLDC 전동기의 코깅토크는 감소되었고 소음진동 또한 줄어들 것이라고 판단된다.

• 대한기계학회논문집A
• /
• 제20권5호
• /
• pp.1573-1581
• /
• 1996

This paper present as experimental demonstratio of DSP and a sensory actuator that is used to actively control sound transmission/radiation through a vibrating plate. A plane acoustic wave incident on a clamped, thin circular plate was used as a noise source, and a sensory actuator bounded to the plate was used to control and sense vibration of the plate. The sound transmission reduction problem was tranformed as a structural vibration control problem that actively control the structural vibration modes coupled to acoustic modes. The results show that the first structural vibration mode is controlled with a reduction of 78 percent in the displacement and velocity of the plate. This corresponds to a 13dB reduction in the acoustic response. These experimental results indicate that a sensory actuator bounded to the plate can be employed to attenuate the sound transmitted to radiated from the plate.

• 대한자기공명의과학회:학술대회논문집
• /
• 대한자기공명의과학회 2003년도 제8차 학술대회 초록집
• /
• pp.94-94
• /
• 2003

목적： 기능적 자기공명영상과 확산텐서영상기법을 이용하여 전음성 난청과 감각신경성 난청에서의 뇌활성화 양상 그리고 청신경경로상의 차이점을 비교 연구하고자 하였다. 대상 및 방법： 전음성 난청군 (n=4)과 감각신경성 난청군(n=5) 그리고 정상군(n=5)에서의 기능적 자기 공명영상과 확산텐서영상을 획득하였다. 기능적 자기공명영상의 경우 1.5T Siemens MR scanner에서 BOLD 기법을 이용하여 500 Hz 순음 청각자극에 대한 뇌활성화 영역을 검출하였고 영상촬영시 발생하는 기계적 소음을 차폐하기 위한 청각자극기를 특별히 제작하여 사용하였다. 뇌백질신경로를 영상화하는 확산텐서영상은 3.0T GE whole body MR scanner를 사용하였으며 미세한 확산운동을 검출하기 위해 초고속 영상기법인 EPI 기법을 사용하였다. 영상의 화질을 높이기 위해 공간적으로 25개의 다른 방향으로 확산경사자장을 가하였다. 청신경로의 비등방성 영상, 신경로 방향 영상등을 구현하기 위해 획득한 확산영상들에 대한 영상 후처리과정을 시행하였다.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2009년도 추계학술대회 논문집
• /
• pp.791-791
• /
• 2009

Hybrid air-foil magnetic bearing combines two oil free bearing technologies to take advantage of the strengths of each bearing with minimizing each other weaknesses. This paper presents bending mode vibration control of a flexible shaft supported by the hybrid air-foil magnetic bearing. An experiment set-up of a flexible shaft supported by the hybrid air-foil magnetic bearing is built. In order to verify the effectiveness of the hybrid bearing, unbalance responses of the flexible shaft supported by three different bearings: air-foil, magnetic and hybrid bearings are compared. Effect of load sharing between air-foil and magnetic bearings are investigated through changing control gain and offset displacements of magnetic bearing.

• 한국소음진동공학회논문집
• /
• 제21권12호
• /
• pp.1091-1097
• /
• 2011

In the present study, TMD(tuned mass damper) with eddy current damping is proposed to suppress the vibration of a cantilever beam effectively. The advantages of TMD are that it is simple and its performance are excellent at any particular frequency. However, TMD may have the low performance at other frequency. To solve this problem and improve its performance, this study applies the eddy current damping to TMD. This TMD with ECD is named as MTMD(magnetically tuned mass damper). MTMD is designed for the vibration suppression of a cantilever beam. The mathematical modeling, simulation, and experiments of the cantilever beam with MTMD are performed. From analytic and experimental results, it can be concluded that the vibration suppression performance of MTMD are excellent.

• 한국소음진동공학회논문집
• /
• 제15권1호
• /
• pp.81-86
• /
• 2005

In this work, we propose a new ultrasonic damage inspection method in plate structures. The proposed method employs an OPMT(orientation-adjustable patch-type magnetostrictive transducer) in order to make the ultrasonic waves directed to a specific target point. For experiments, virtual grid points were set up at every 50 mm in an aluminum plate and two OPMTs were used for inspection. If there exists a crack in a plate, the reflected Lamb wave from the crack is measured in addition to the direct waves from the transmitting transducer to the receiving transducer.

• 소음진동
• /
• 제6권3호
• /
• pp.357-362
• /
• 1996

The magnetic levitation system has great advantages, such as little friction, no lubrication, no noise and so on. But the magnetic levitation system need a stabilizing controller because it is a unstable, system in natural and it need a sensor for displacement measurement to control the system. In this paper, we proposed a sensorless method to measure the gap between the magnetic pole and the levitated object with application the inductance characteristic which vary according to gap. We made a driving circuit which supply simultaneously the control input PWM(Pulse Width Modulation) signal and the carrier PWM signal to estimate the gap. Because the inductance is a function of gap, and the current of the carrier signal is a function of the inductance, we could estimate the gap from the measurement of the current of the carrier signal. Finally, we investigated the validity of the proposed method through the experimental results.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2005년도 춘계학술대회논문집
• /
• pp.504-507
• /
• 2005

This paper presents a self-levelling system for a mass, which undergoes a severe acceleration, with integrated displacement feedback control. After a general description of such a system, theoretical analysis is investigated to design an active control device. That is, the self levelling system is used to reduce the 'static' deflections while isolating the 'dynamic' vibration. A computer simulation model of 45 kg with two air spring mounts is considered to predict the performance of the control system. The results showed the controller can reduce the mass's displacement to the level of 1/3-1/5. Thus the self-levelling system can be applied usefully to reduce the dispalcement of a mass which experiences a high g dynamics.

• 소음진동
• /
• 제10권2호
• /
• pp.331-337
• /
• 2000

The necessity of diagnosis of the rotating machinery which is widely used in the industry is increasing. Many research has been conducted to manipulate field vibration signal data for diagnosing the fault of designated machinery. As the pattern recognition tool of that signal, neural network which use usually back-propagation algorithm was used in the diagnosis of rotating machinery. In this paper, self-organizing feature map(SOFM) which is unsupervised learning algorithm is used in the abnormal defect diagnosis of rotating machinery and then learning vector quantization(LVQ) which is supervised learning algorithm is used to improve the quality of the classifier decision regions.

• 한국소음진동공학회논문집
• /
• 제13권4호
• /
• pp.308-316
• /
• 2003

Terfenol-D is one of magnetostrictive materials which have the property of converting the energy in magnetic fields into mechanical movement and vice versa. We designed and fabricated a linear magnetostrictive actuator using Terfenol-D. It has 25 mm diameter and 100 mm long. To grasp the characteristics of it, a series of tests were performed in the range of 50 Hz below. Induced-strain actuation displacements of the actuator measured by test and predicted by magnetic analysis agreed well. And blocked forces according to the input currents were estimated from the testing results. Modelling method representing the exerting force of a linear magnetostrictive actuator was confirmed through some testing results.