• Journal of Biosystems Engineering
• /
• v.20 no.3
• /
• pp.236-244
• /
• 1995

Droplet size is one of the important factors in the deposition and drift of agrichemical application. In this study, droplet size and its distribution of the three different sizes of ceramic hollow cone nozzles being used in the air carrier sprayer for apple production were investigated at the various nozzle pressures and the three air velocities. The Malvern particle size analyzer were used for the measurement of droplet size and its distribution. The important results emerged from th is study can be summarized as follows. 1. Discharged rate was increase with the increase of the nozzle diameter and pressure, amount of the difference was remarkable between the nozzle diameter of 1.0, 1.2 and 1.5 mm, but no difference were found between the diameter of 1.0 and 1.2 mm in the same nozzle pressure. 2. Mass median diameter were varied as 40~160 ${mu}m$ at the air velocity of 0 m/s, 70~140 ${mu}m$ of 15 m/s and 100~160 ${mu}m$ of 20 m/s 3. It appeared that the air velocity range of 15~20 m/s was desirable for both drift and deposition control in the given experimental conditions.

• Journal of Korean Society for Atmospheric Environment
• /
• v.2 no.2
• /
• pp.41-50
• /
• 1986

Urban aerosol concentrations in the size range of $0.01 \sim 1.0 \mum$ have been measured by using an electrical aerosol analyzer from May through October, 1984. The total diurnal variation of the number concentration indicates that a minimum value is observed at 3 hr and a sharp increase is noticed early in the morning with a subsequent slow and continuous increase from around 7 hr until 20 hr. After that it is decreased to reach its minimum by dawn. However, both surface and volume concentrations have shown that their first maxima at 8 hr and their second at about 20 hr simultaneously. It is found that the aerosol number is mainly governed by the particles in the size range of $0.01 \sim 0.1 \mum$, while most volume is in $0.1 \sim 1.0 \mum$ size range. It is known fact that particles of $0.1 \sim 1.0 \mum$ size range affect the visibility reduction in the atmosphere. The monthly variation of aerosol concentration remarks its minimum in summer. The main factors influencing the aerosol concentration are emission of autoexhausts, various processes of production and removal, and meteorological parameters.

• Resources Recycling
• /
• v.9 no.1
• /
• pp.21-26
• /
• 2000

Extraction of manganese was investigated with nitric acid from the dust which was generated in the AOD process producing a medium-low carbon ferromanganese from a high carbon ferromanganese. Content of manganese oxide in the dust was about 90%, and phase of it was confirmed as $Mn_3O_4$, The $Mn_3O_4$ particles was agglomerated as spherical shape, and had a lot of pore and crack inside. Maximum recovery of Mn from the sample in the leaching step was about 67% and residue was the amorphous $MnO_2$. The extraction of Mn increased with increasing temperature, but decreased in proportion to concentration of nitric acid. The extraction rate was in good agreement with the pore diffusion model.

• Journal of the Korean Society for Railway
• /
• v.13 no.1
• /
• pp.78-83
• /
• 2010

On the paved track, the ballast is used as aggregate for the filling layer using the pre-packed concrete technique. The most important condition of aggregate is adhesive strength with mortar. To satisfy this condition, surface of aggregate should be cleaned by water or others. In a paved-track method to be introduced domestically, an environment-friendly dry-washing technology which will replace the water-washing method has been developed. A dry-washing method was designed to blast the crushed weight material with a diameter of 0.3~0.5mm at high pressure to peel the surface of the aggregate. The study was intended to enhance the washing efficiency of dry-blasting technology and to that end, the tests including blasting material, content of fine aggregate depending on time elapsed, content of chloride, LA abrasion rate and compressive strength were conducted to recommend the efficient washing material and the process.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.177-180
• /
• 2009

A Possibility of combustion instability on longitudinal mode has a high level at large scale of L/D. Solid propellant has a metal particle and a grain of control to pressure oscillation. Solid rocket motor in slotted-tube grain controls pressure oscillation of longitudinal mode. If slot length is shot, pressure oscillation of longitudinal mode is amplified by cylinder part after middle phase of total burn time. A study has analyzed pressure oscillation of longitudinal mode at spectrum and acoustic modal analysis at pressure of result on static firing test.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• 2009.05a
• /
• pp.99-102
• /
• 2009

LES(Large eddy simulation) of breakup and atomization of a liquid jet into cross turbulent flow was performed. Two phase flow between a gas phase and a liquid phase was modeled by a mixed numerical scheme of both Eulerian and Lagrangian methods for gas and liquid phases respectively. The first and second breakup of liquid column was observed. The penetration depth in cross flow was comparable with experimental data for several variant of a liquid-gas momentum flux ratio by varying liquid injection velocities. SMD(Sauter Mean Diameter) distribution downstream of jet was analyzed.

• Proceedings of the KIEE Conference
• /
• 2009.04a
• /
• pp.27-29
• /
• 2009

본 연구에서는 Titanate Nanotube (TNT)를 LBL-SA (layer-by-layer self-assembling) method을 이용하여 전기변색 (electrochromism device, ECD) 소자에 적용하고자 하였다. TNT 분말은 10M NaOH와 $TiO_2$를 혼합한 후 autoclave에서 130$^{\circ}C$, 48시간 동안 수열합성하여 제조하였다. 주사전자현미경 (SEM)으로 TNT 분말의 형상을 관찰한 결과, 직경 20$\sim$30nm, 길이 500$\sim$600nm의 튜브 형상을 나타내었으며, X-선 회절시험 (XRD) 결과 층상구조로 확인되었다. 코팅 물질의 표면 전하를 이용한 LBL-SA method에 적용시키기 위해 수용액 중에서 TNT 입자 표면 전하를 TBAOH (tetrabutylammonium hydroxide)를 적정하여 제타 전위 값이 -40mV로 최대가 되도록 하였으며, 이때 pH 값은 9로 나타났다. 2전극 시스템을 이용하여 cycle voltammetry를 측정한 결과, -0.5$\sim$-1.5V 영역에서 산화환원전위 피크가 뚜렷하게 나타났으며, 짙은 갈색으로 변색되는 것을 확인하였다. 본 연구 결과로서 TNT 박막은 전기를 인가하였을 때 n-type 반도체 성질을 갖는 것으로 나타났으며, 앞으로 display 연구 분야에 적용할 수 있을 것으로 주목된다.

• Journal of ILASS-Korea
• /
• v.8 no.3
• /
• pp.41-48
• /
• 2003

This work was performed to investigate the distribution of the fuel droplet size around the bluff-body and the combustion characteristics. The bluff-body is used fur the purpose of increasing the combustion efficiency by stabilizing the flame. Diameters of the bluff-body in this experiment are 6, 8, and 10mm and the impingement angles are $30^{\circ},\;60^{\circ}\;and\;90^{\circ}$. The measurement points were at the distances of 20 and 30 mm axially from the nozzle. The geometry of the bluff-body influenced the spray shape and the combustion characteristics. The SMD was acquired by image processing technique (PMAS), and the mean temperatures were measured by thermocouple. In the condition of ${\theta}=60^{\circ}$, the values of SMD are not greatly varied compared to the other conditions. As the angle of bluff-body was increased, the high temperature region was wider along radial direction. When the air-fuel ratio was larger than 5.2, the NOx concentration was decreased, and an increase in the diameter of the bluff-body decreased the NOx of emission.

• Korean journal of applied entomology
• /
• v.18 no.1 s.38
• /
• pp.11-14
• /
• 1979

Spinaches showing dark green mosaic symptoms were used for identification of broad bean wilt virus. In host reaction test, that virus caused local lesions on the inoculated leaves and mosaic symptoms on upper leaves of Chenopodium amaranticolor, Chenopodium quinoa and Vicia faba, and developed mosaic symptoms on Physalis floridana, Spinacia oleracea, Nicotiana tabacum, (White burley, Bright yellow) Nicotiana glutinusa. In agar gel-diffusion test, the virus showed positive reaction with broad bean wilt virus antiserum. Spherical virus particles with size of 25nm in diameter were observed in electron microscope.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.290.1-290.1
• /
• 2014

스핀코팅방법으로 증착된 ZnO 박막의 단계적 후열처리에 따른 구조적, 광학적 특성에 관한 연구를 수행하였다. 일반적으로 ZnO 박막은 한 층을 증착한 후에, 유기물을 제거하기 위하여 전열처리를 수행한다. 본 연구에서는 ZnO 박막을 전열처리와 후열처리를 동시에 단계적으로 수행하였다. X-ray diffractometer, UV-visible spectrometer, photoluminescence를 이용하여 ZnO 박막의 구조적, 광학적 특성을 분석하였다. 모든 시료에서 표면은 직경이 약 20 nm인 둥근 입자들로 이루어져 있었다. X-ray diffraction 패턴은 $31^{\circ}$, $34^{\circ}$, $36^{\circ}$에서 나타났고, 이것은 각각 ZnO의 (100), (002), (101) 방향을 보여준다. 전열처리와 후열처리를 동시에 수행했을 경우, 자유엑시톤 재결합에 의해 3.2 eV에서 좁은 near-band-edge emission 피크가 나타났으며, 투과도 또한 향상되었다.