• Journal of the Korean Recycled Construction Resources Institute
• /
• v.8 no.3
• /
• pp.317-324
• /
• 2020

Plastic wastes generated from domestic waste are separated by mixed discharge with foreign substances, and the cost of the separation and screening process increases, so recycling is relatively low. In this study, as a fundamental study for recycling mixed plastic wastes generated from domestic waste into concrete aggregates, changes in concrete properties according to the plastic waste types and the substitution rate were evaluated experimentally. The mixed plastic waste aggregate(MPWA) was found to have a lower density and a higher absorption rate compared to the coarse aggregate with good particle size distribution. On the other hand, the single plastic waste aggregate(SPWA) was composed of particles of uniform size, and both the density and the absorption rate were lower than that of the fin e aggregate. It was found that the MPWA substitution concrete did not cause a material separation phenomenon due to a relatively good particle size distribution even with the largest amount of plastic waste substitution, and the amount of air flow increased little. The compressive strength and flexural strength of the PWA substitution concrete decreased as the amount of substitution of the PWA increased due to the low strength of the PWA, the suppression of the cement hydration reaction due to hydrophobicity, and the low adhesion between the PWA and the cement paste. It was found that the degree of deterioration in compressive strength and flexural strength of concrete substituted with MPWA having good particle size distribution was relatively small.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.24 no.4
• /
• pp.105-112
• /
• 2016

The drying test was carried on the globular type cow manure pellet for use in solid fuel applications. The globular type cow manure pellet fuel was sorted according to size by rotatory sieves. The three kind of drying methods such as convection hot-air drying method, infrared ray drying method and superheated steam method were used to dry the globular type cow manure pellet. Among the three kind of drying methods, superheated steam method of dry time was the shortest. The apparent specific gravity and low calorific value of dried cow manure pelltes was about $250{\sim}350kg/m^3$ and above 3,000 kcal/kg respectively. The smaller the particle size of cow manure pellets, the less drying time was required. The time was required very less for drying smaller particle size cow manure pellet when compared to larger size. In the case of the same drying condition, it has been found that reducing the particle size of cow manure fuel pellet is an important factor for shortening the drying time of the livestock manure pellet.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.9 no.3
• /
• pp.253-259
• /
• 2021

Plastic wastes generated from household waste are separated by mixed discharge with foreign substances, and recycling is relatively low. In this study, the effect of the ratio and content of mixed plastic waste coarse aggregate(MPWCA)s and mixed plastic waste fine aggregate(MPWFA)s filled with blast furnace slag fine powder on the slump and compressive strength of concrete was evaluated experimentally. The MPWCAs were found to have a similar fineness modulus, but have a single particle size distribution with a smaller particle size compared to coarse aggregates. However, the MPWFAs were found to have a single particle size distribution with a larger fineness modulus and particle size compared to fine aggregates. Meanwhile, the effect of improving the density and filling pores by the blast furnace slag fine power was found to be greater in the MPWFA compared to the MPWCA. As the amount of the mixed plastic waste aggregate(MPWA)s increased, the slump and compressive strength of concrete decreased. In particular, the lower the slump and compressive strength of concrete was found to decrease the greater the amount of MPWFA than MPWCA when the amount of MPWA was the same. This is because of the entrapped air and voids formed under the angular- and ROD-shaped aggregates among the MPWFAs. On the other hand, the addition of the admixture and the increase in the unit amount of cement were found to be effective in improving the compressive strength of the concrete with MPWAs.

• Korean Journal of Food Science and Technology
• /
• v.23 no.4
• /
• pp.478-484
• /
• 1991

As a work on the preparation of spread type product using chungkook-jang, proximate composition and enzyme activity of chungkook-jang were analyzed and extrusion capillary viscometer was made. The effects of moisture content, oil type and content and temperature on the rheological properties of chungkook-jang spread were investigated. As the moisture content of chungkook-jang spread increased from 55% to 65%, apparent viscosity $({\eta}a)$ decreased and spreadibility and L value in Hunter color system increased. On the contrary, as the added oil content of chungkook-jang spread increased from 10% to 30%, rla increased and spreadibility and L value decreased. Specially, in case of palm olefin addition, the rla of chungkook-jang spread was more high than that of soybean oil addition. As the temperature of chungkook-jang spread increased, rla decreased and spreadibility increased. In the same conditions, the ${\eta}a$ of chungkook-jang spread increased in order of B. natto, B. natto and B. subtilis mixture and B. subtilis fermentation.

• Membrane Journal
• /
• v.26 no.6
• /
• pp.421-431
• /
• 2016

Novel membrane technologies that harness ordered nanostructures have recently received much attention because they allow for high permeability due to their reduced flow resistance while also maintaining high selectivity due to their isoporous characteristics. In particular, the opaline structure (made from the self-assembly of colloidal particles) and its inverted form (inverse-opal) have shown strong potential for membrane applications on account of several advantages in processing and the resulting membrane properties. These include controllability over the pore size and surface functional moieties, which enable a wide range of applications ranging from size-exclusive separation to catalytically-reactive membranes. Furthermore, when combined with multiscale architecturing strategies, inverse-opal-structured membranes can be designed to have specific pores or channel structures. These materials are anticipated to be utilized for next-generation, high-performance, and high-value-added functional membranes. In this review article, various types of inverse-opal-structured membranes are reviewed and their functionalization through hierarchical structuring will be comprehensively investigated and discussed.

• Journal of Nuclear Fuel Cycle and Waste Technology(JNFCWT)
• /
• v.14 no.4
• /
• pp.321-329
• /
• 2016

Based on the results of groundwater flow system modeling for a hypothetical deep geological repository site, quantitative and spatial distributions of groundwater flow rates at the positions of deposition holes, groundwater travel length and time from the positions to the surface environment were analyzed and used to suggest a method for determining locations of deposition holes. The hydraulic head values at the depth of the deposition holes and a particle tracking method were used to calculate the ground-water flow rates and groundwater travel length and time, respectively. From the results, an approach to designing a layout of deposition holes was suggested by selecting relatively favorable positions for maintaining performance of the disposal facility and screening some positions of deposition holes that did not comply with specific constraints for the groundwater flow rates, travel length and time. In addition, a method for determining a geometrical direction for extension of the disposal facility was discussed. Designing the layout of deposition holes with the information of groundwater flow at the disposal depth can contribute to secure performance and safety of the disposal facility.

• Journal of the Korean Society of Visualization
• /
• v.20 no.3
• /
• pp.136-145
• /
• 2022

Later flow immunoassay (LFIA) is a protein analytical method based on immunoreaction. On the LFIA based protein analytical method, bioreceptor molecule plays a key role, and so a system that evaluates and manages the binding affinity of bioreceptor is needed to secure detection reliability. In this study, Lateral Flow Immunoassay based rapid Bioreceptor Screening Method (rBSM) is presented that provide a simple and quick evaluating method for the binding affinity to the target protein of the antibody as model bioreceptor. To verify this evaluation method, Virus-like particles (VLP) and anti-VLP antibodies are selected as a model norovirus, which is target protein, and the candidate bioreceptors respectively. Among the 5 different candidate antibodies, appropriate antibody could be sorted out within 30 minutes through rBSM. In addition, selected antibodies were applied to two representative LFIA based techniques, sandwich assay and competitive assay. Among these methods, sandwich assay showed more effective VLP detection method. Through applying selected antibodies and techniques to the commercialized mass production lines, an VLP detecting LFIA kit was developed with a detection limit of 10¹² copies/g of VLPs in real samples. Since this proposed method in this study could be easily transformable into other combinations with bioreceptors, it is expected that this technique would be applied to LFIA kit development system and bioreceptor quality management.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2021.06a
• /
• pp.66-66
• /
• 2021

2011년에 일본 도호쿠 지방 태평양 해역에서 규모 9.0의 지진이 발생하여 거대한 쓰나미가 일본 본토 해안을 침수시켰다. 이로 인해, 정확한 피해규모가 파악되기 어려울 정도로 막대한 인명과 재산피해를 입게 되었다. 센다이지역의 경우 쓰나미로 인해 해안에 위치한 약 3.8 평방킬로미터의 방풍림이 모두 전복되었고 일부는 유목이 되어 쓰나미와 함께 내륙으로 흘러들어가 곳곳에 퇴적되어 농지를 훼손하고 가옥에 피해를 주었다. 따라서, 본 연구는 유목의 발생과 흐름에 따른 거동을 수치적으로 분석하여, 폭우나 쓰나미와 같은 거대흐름과 산지와 방풍림 등에서 발생하는 유목의 발생과 거동과정을 예측하고, 흐름과 유목 거동에 따른 피해지역을 선별할 수 있는 방법을 구축하기 위한 초기단계로서, 이를 위해 유목의 발생과정의 역학적 모델링을 수치모듈에 적용하였고 이를 활용하여 수치모의를 수행하였다. 흐름분석을 위해 쓰인 모형은 홍수범람 모형인 Nays2D Flood 이며 천수방정식을 기본으로 한다. 쓰나미의 흐름은 해안가의 방풍림지역을 상류단 경계조건으로 하여 발생 당시 관측된 수심변화를 본 모형의 상류단 경계조건으로 입력하였다. 상류단 경계조건에서 쓰나미의 유속은 수심에 따른 파속으로 계산하였다. 본 연구에서는 또한 유목의 발생과 흐름거동을 기존에 개발된 입자법 기반의 유목동역학모형을 활용하여 수치적으로 모델링 하였다. 유목은 유연성이 없는 원주형 강체로 가정하였고 초기설정으로는, 방풍림지역에 30만개의 유목이 하상의 수직방향으로 배치되어있는 것으로 가정하였다. 여기서, 본 연구에서는 쓰나미가 발생하면 흐름에 따른 항력으로 인해 수직방향으로 배치된 유목이 부러지며, 흐름과 함께 흘러가는 현상을 모델링하였다. 본 연구는 폭우나 쓰나미와 같은 거대흐름으로 인해 발생할 수 있는 유송잡물과 유목의 거동을 예측분석하는 기초연구자료로 활용될 수 있으며, 더 나아가 유목의 발생과정까지 수치적으로 재현하는 모델링을 수행하였기 추후에, 산지와 하천에서 발생할 수 있는 유송잡물의 발생과 연행 과정을 보다 세부적으로 예측할 수 있는 기초방법론으로 쓰일 수 있을 것으로 판단된다.

• Journal of the Computational Structural Engineering Institute of Korea
• /
• v.37 no.2
• /
• pp.143-149
• /
• 2024

Segmentation of material phases through image analysis is essential for analyzing the microstructure of materials. Micro-CT images exhibit variations in grayscale values depending on the phases constituting the material. Phase segmentation is generally achieved by comparing the grayscale values in the images. In the case of waste concrete used as a recycled aggregate, it is challenging to distinguish between hydrated cement paste and natural aggregates, as these components exhibit similar grayscale values in micro-CT images. In this study, we propose a method for automatically separating the aggregates in concrete, in micro-CT images. Utilizing the Unet-VGG16 deep-learning network, we introduce a technique for segmenting the 2D aggregate images and stacking them to obtain 3D aggregate images. Image filtering is employed to separate aggregate particles from the selected 3D aggregate images. The performance of aggregate segmentation is validated through accuracy, precision, recall, and F1-score assessments.

• The Korean Journal of Nuclear Medicine Technology
• /
• v.14 no.1
• /
• pp.35-39
• /
• 2010

Purpose: The aim of this study was to investigate distribution of particle size in phytate kit and compare filtered method with non-filtered method using 200 nm filter for sentinel lymphoscintigraphy (SLS). Materials and Methods: Five phytate kit of having the same available period was measured by particle size analyzer. For in-vivo experiment, $^{99m}Tc$-phytate was injected intradermally at both foot to perform lymphoscintigraphy. Imaging was acquired at 1hour after injection. Region of interest (ROI) was drawn in inguinal and background area for analysis. RAW 264.7 cells (Murine macrophage cell) were prepared for measurement of celluar uptake as a representative of macrophages. Paired t-test was performed using SPSS (SPSS Inc, USA) for statistical analysis. Results: The size of most particle in Techne phytate kit was distributed in 130~650 nm(90.5 %). In-vivo study, the ROI analysis showed similar result between filtered and non-filtered sample, and the numerical value of count/pixel were $58.3{\pm}5.97$ and $60.2{\pm}4.88$. In-vitro study, cellular uptake study also showed no difference between filtered and non-filtered sample by gamma counting. Conclusion: The present study demonstrates that there was no meaning of 200 nm filtered method for SLS using $^{99m}Tc$-phytate.